I am trying to compare the FFT of exp(-t^2) to the function's analytical fourier transform, exp(-(w^2)/4)/sqrt(2), over the frequency range -3 to 3.
I have written the following matlab code and have iterated on it MANY times now with no success.
fs = 100; %sampling frequency
dt = 1/fs;
t = 0:dt:10-dt; %time vector
L = length(t); %number of sample points
%N = 2^nextpow2(L); %necessary?
y = exp(-(t.^2));
Y=dt*ifftshift(abs(fft(y)));
freq = (-L/2:L/2-1)*fs/L; %freq vector
F = (exp(-(freq.^2)/4))/sqrt(2); %analytical solution
%Y_valid_pts = Y(W>=-3 & W<=3); %compare for freq = -3 to 3
%npts = length(Y_valid_pts);
% w = linspace(-3,3,npts);
% Fe = (exp(-(w.^2)/4))/sqrt(2);
error = norm(Y - F) %L2 Norm for error
hold on;
plot(freq,Y,'r');
plot(freq,F,'b');
xlabel('Frequency, w');
legend('numerical','analytic');
hold off;
You can see that right now, I am simply trying to get the two plots to look similar. Eventually, I would like to find a way to do two things:
1) find the minimum sampling rate,
2) find the minimum number of samples,
to reach an error (defined as the L2 norm of the difference between the two solutions) of 10^-4.
I feel that this is pretty simple, but I can't seem to even get the two graphs visually agree.
If someone could let me know where I'm going wrong and how I can tackle the two points above (minimum sampling frequency and minimum number of samples) I would be very appreciative.
Thanks
A first thing to note is that the Fourier transform pair for the function exp(-t^2) over the +/- infinity range, as can be derived from tables of Fourier transforms is actually:
Finally, as you are generating the function exp(-t^2), you are limiting the range of t to positive values (instead of taking the whole +/- infinity range).
For the relationship to hold, you would thus have to generate exp(-t^2) with something such as:
t = 0:dt:10-dt; %time vector
t = t - 0.5*max(t); %center around t=0
y = exp(-(t.^2));
Then, the variable w represents angular frequency in radians which is related to the normalized frequency freq through:
w = 2*pi*freq;
Thus,
F = (exp(-((2*pi*freq).^2)/4))*sqrt(pi); %analytical solution
Related
I'm studying the IFFT in Matlab by applying it to a Gaussian. According to Wikipedia tables, the Fourier transform pair would be
F(w) = sqrt(pi/a) * exp(-w^2/(4a))
in frequency, and
f(t) = exp(-at^2)
in time. I modified the code in a previous question plus Cris Luengo's answer to perform this IFFT.
a = 0.333;
ts = 1e4; % time sampling
L = 1000*ts; % no. sample points
ds = 1/ts;
f = -floor(L/2):floor((L-1)/2); % freq vector
f = f/ts;
w = 2*pi*f; % angular freq
Y = sqrt(pi/a)*exp(-w.^2/(4*a));
y = ts*ifftshift(ifft(fftshift(Y)));
t = (-L/2:L/2-1)*ts/L; % time vector
f = exp(-a*t.^2); % analytical solution
figure; subplot(1,2,1); hold on
plot(t,real(y),'.--')
plot(t,real(f),'-')
xlabel('time, t')
title('real')
legend('numerical','analytic')
xlim([-5,5])
subplot(1,2,2); hold on
plot(w,imag(y),'.--')
plot(w,imag(f),'-')
xlabel('time, t')
title('imag')
legend('numerical','analytic')
xlim([-5,5])
When I compare the result of IFFT with the analytical expression, they don't seem to agree:
I'm not sure where the mistake is. Have I scaled the IFFT properly? Is there an error in how I define the linear/angular frequency?
Edit: For some reason, when I define L=ts^2 the analytical and numerical solutions seem to agree (L = no. sampling points, ts = time sample).
Starting from the analytical solution, let's rephrase things a bit. You have a sampling of the function f(t) = exp(-a*t^2), and the way you've constructed the analytical answer you're collecting L=1000*ts=1e7 samples at a sampling rate of Ts=ts/L=1e-3. This means that your sampling frequency is Fs=1/Ts=1e3.
Since you want to compare against results obtained with fft/ifft, you should be considering digital or discrete frequencies, meaning the values you define for your transform will correspond to the digital frequencies
frd = (-L/2:L/2-1)/L;
Mapping this to angular frequencies, we have:
w = 2*pi*frd;
But when you're trying to compute the values, you also need to keep in mind that these frequencies should represent samples of the continuous time spectrum you're expecting. So you scale these values by your sampling frequency:
Y = sqrt(pi/a)*exp(-(Fs*w).^2/(4*a));
y = Fs*ifftshift(ifft(fftshift(Y)));
When you compare the analytical and computed answers, they now match.
The short answer to your question, given this, is that you are scaling y incorrectly at the end. You're scaling it by ts, which is 1e4, but you need to be scaling it by the sampling frequency which is Fs=1e3. That's why you end up off by a factor of 10.
I have adapted the code in Comparing FFT of Function to Analytical FT Solution in Matlab for this question. I am trying to do FFTs and comparing the result with analytical expressions in the Wikipedia tables.
My code is:
a = 1.223;
fs = 1e5; %sampling frequency
dt = 1/fs;
t = 0:dt:30-dt; %time vector
L = length(t); % no. sample points
t = t - 0.5*max(t); %center around t=0
y = ; % original function in time
Y = dt*fftshift(abs(fft(y))); %numerical soln
freq = (-L/2:L/2-1)*fs/L; %freq vector
w = 2*pi*freq; % angular freq
F = ; %analytical solution
figure; subplot(1,2,1); hold on
plot(w,real(Y),'.')
plot(w,real(F),'-')
xlabel('Frequency, w')
title('real')
legend('numerical','analytic')
xlim([-5,5])
subplot(1,2,2); hold on;
plot(w,imag(Y),'.')
plot(w,imag(F),'-')
xlabel('Frequency, w')
title('imag')
legend('numerical','analytic')
xlim([-5,5])
If I study the Gaussian function and let
y = exp(-a*t.^2); % original function in time
F = exp(-w.^2/(4*a))*sqrt(pi/a); %analytical solution
in the above code, looks like there is good agreement when the real and imaginary parts of the function are plotted:
But if I study a decaying exponential multiplied with a Heaviside function:
H = #(x)1*(x>0); % Heaviside function
y = exp(-a*t).*H(t);
F = 1./(a+1j*w); %analytical solution
then
Why is there a discrepancy? I suspect it's related to the line Y = but I'm not sure why or how.
Edit: I changed the ifftshift to fftshift in Y = dt*fftshift(abs(fft(y)));. Then I also removed the abs. The second graph now looks like:
What is the mathematical reason behind the 'mirrored' graph and how can I remove it?
The plots at the bottom of the question are not mirrored. If you plot those using lines instead of dots you'll see the numeric results have very high frequencies. The absolute component matches, but the phase doesn't. When this happens, it's almost certainly a case of a shift in the time domain.
And indeed, you define the time domain function with the origin in the middle. The FFT expects the origin to be at the first (leftmost) sample. This is what ifftshift is for:
Y = dt*fftshift(fft(ifftshift(y)));
ifftshift moves the origin to the first sample, in preparation for the fft call, and fftshift moves the origin of the result to the middle, for display.
Edit
Your t does not have a 0:
>> t(L/2+(-1:2))
ans =
-1.5000e-05 -5.0000e-06 5.0000e-06 1.5000e-05
The sample at t(floor(L/2)+1) needs to be 0. That is the sample that ifftshift moves to the leftmost sample. (I use floor there in case L is odd in size, not the case here.)
To generate a correct t do as follows:
fs = 1e5; % sampling frequency
L = 30 * fs;
t = -floor(L/2):floor((L-1)/2);
t = t / fs;
I first generate an integer t axis of the right length, with 0 at the correct location (t(floor(L/2)+1)==0). Then I convert that to seconds by dividing by the sampling frequency.
With this t, the Y as I suggest above, and the rest of your code as-is, I see this for the Gaussian example:
>> max(abs(F-Y))
ans = 4.5254e-16
For the other function I see larger differences, in the order of 6e-6. This is due to the inability to sample the Heaviside function. You need t=0 in your sampled function, but H doesn't have a value at 0. I noticed that the real component has an offset of similar magnitude, which is caused by the sample at t=0.
Typically, the sampled Heaviside function is set to 0.5 for t=0. If I do that, the offset is removed completely, and max difference for the real component is reduced by 3 orders of magnitude (largest errors happen for values very close to 0, where I see a zig-zag pattern). For the imaginary component, the max error is reduced to 3e-6, still quite large, and is maximal at high frequencies. I attribute these errors to the difference between the ideal and sampled Heaviside functions.
You should probably limit yourself to band-limited functions (or nearly-band-limited ones such as the Gaussian). You might want to try to replace the Heaviside function with an error function (integral of Gaussian) with a small sigma (sigma = 0.8 * fs is the smallest sigma I would consider for proper sampling). Its Fourier transform is known.
I have an instrument which produces roughly sinusoidal data, but with frequency varying slightly in time. I am using MATLAB to prototype some code to characterize the time dependence, but I'm running into some issues.
I am generating an idealized approximation of my data, I(t) = sin(2 pi f(t) t), with f(t) variable but currently tested as linear or quadratic. I then implement a sliding Hamming window (of width w) to generate a set of Fourier transforms F[I(t), t'] corresponding to the data points in I(t), and each F[I(t), t'] is fit with a Gaussian to more precisely determine the peak location.
My current MATLAB code is:
fs = 1000; %Sample frequency (Hz)
tlim = [0,1];
t = (tlim(1)/fs:1/fs:tlim(2)-1/fs)'; %Sample domain (t)
N = numel(t);
f = #(t) 100-30*(t-0.5).^2; %Frequency function (Hz)
I = sin(2*pi*f(t).*t); %Sample function
w = 201; %window width
ww=floor(w/2); %window half-width
for i=0:2:N-w
%Take the FFT of a portion of I, convolved with a Hamming window
II = 1/(fs*N)*abs(fft(I((1:w)+i).*hamming(w))).^2;
II = II(1:floor(numel(II)/2));
p = (0:fs/w:(fs/2-fs/w))';
%Find approximate FFT maximum
[~,maxIx] = max(II);
maxLoc = p(maxIx);
%Fit the resulting FFT with a Gaussian function
gauss = #(c,x) c(1)*exp(-(x-c(2)).^2/(2*c(3)^2));
op = optimset('Display','off');
mdl = lsqcurvefit(gauss,[max(II),maxLoc,10],p,II,[],[],op);
%Generate diagnostic plots
subplot(3,1,1);plot(p,II,p,gauss(mdl,p))
line(f(t(i+ww))*[1,1],ylim,'color','r');
subplot(3,1,2);plot(t,I);
line(t(1+i)*[1,1],ylim,'color','r');line(t(w+i)*[1,1],ylim,'color','r')
subplot(3,1,3);plot(t(i+ww),f(t(i+ww)),'b.',t(i+ww),mdl(2),'r.');
hold on
xlim([0,max(t)])
drawnow
end
hold off
My thought process is that the peak location in each F[I(t), t'] should be a close approximation of the frequency at the center of the window which was used to produce it. However, this does not seem to be the case, experimentally.
I have had some success using discrete Fourier analysis for engineering problems in the past, but I've only done coursework on continuous Fourier transforms--so there may be something obvious that I'm missing. Also, this is my first question on StackExchange, so constructive criticism is welcome.
So it turns out that my problem was a poor understanding of the mathematics of the sine function. I had assumed that the frequency of the wave was equal to whatever was multiplied by the time variable (e.g. the f in sin(ft)). However, it turns out that the frequency is actually defined by the derivative of the entire argument of the sine function--the rate of change of the phase.
For constant f the two definitions are equal, since d(ft)/dt = f. But for, say, f(t) = sin(t):
d(f(t)t)/dt = d(sin(t) t)/dt = t cos(t) + sin(t)
The frequency varies as a function very different from f(t). Changing the function definition to the following fixed my problem:
f = #(t) 100-30*(t-0.5).^2; %Frequency function (Hz)
G = cumsum(f(t))/fs; %Phase function (Hz)
I = sin(2*pi*G); %Sampling function
I have a series of 2D measurements (time on x-axis) that plot to a non-smooth (but pretty good) sawtooth wave. In an ideal world the data points would form a perfect sawtooth wave (with partial amplitude data points at either end). Is there a way of calculating the (average) period of the wave, using OCTAVE/MATLAB? I tried using the formula for a sawtooth from Wikipedia (Sawtooth_wave):
P = mean(time.*pi./acot(tan(y./4))), -pi < y < +pi
also tried:
P = mean(abs(time.*pi./acot(tan(y./4))))
but it didn't work, or at least it gave me an answer I know is out.
An example of the plotted data:
I've also tried the following method - should work - but it's NOT giving me what I know is close to the right answer. Probably something simple and wrong with my code. What?
slopes = diff(y)./diff(x); % form vector of slopes for each two adjacent points
for n = 1:length(diff(y)) % delete slope of any two points that form the 'cliff'
if abs(diff(y(n,1))) > pi
slopes(n,:) = [];
end
end
P = median((2*pi)./slopes); % Amplitude is 2*pi
Old post, but thought I'd offer my two-cent's worth. I think there are two reasonable ways to do this:
Perform a Fourier transform and calculate the fundamental
Do a curve-fitting of the phase, period, amplitude, and offset to an ideal square-wave.
Given curve-fitting will likely be difficult because of discontinuities in saw-wave, so I'd recommend Fourier transform. Self-contained example below:
f_s = 10; # Sampling freq. in Hz
record_length = 1000; # length of recording in sec.
% Create noisy saw-tooth wave, with known period and phase
saw_period = 50;
saw_phase = 10;
t = (1/f_s):(1/f_s):record_length;
saw_function = #(t) mod((t-saw_phase)*(2*pi/saw_period), 2*pi) - pi;
noise_lvl = 2.0;
saw_wave = saw_function(t) + noise_lvl*randn(size(t));
num_tsteps = length(t);
% Plot time-series data
figure();
plot(t, saw_wave, '*r', t, saw_function(t));
xlabel('Time [s]');
ylabel('Measurement');
legend('measurements', 'ideal');
% Perform fast-Fourier transform (and plot it)
dft = fft(saw_wave);
freq = 0:(f_s/length(saw_wave)):(f_s/2);
dft = dft(1:(length(saw_wave)/2+1));
figure();
plot(freq, abs(dft));
xlabel('Freqency [Hz]');
ylabel('FFT of Measurement');
% Estimate fundamental frequency:
[~, idx] = max(abs(dft));
peak_f = abs(freq(idx));
peak_period = 1/peak_f;
disp(strcat('Estimated period [s]: ', num2str(peak_period)))
Which outputs a couple of graphs, and also the estimated period of the saw-tooth wave. You can play around with the amount of noise and see that it correctly gets a period of 50 seconds till very high levels of noise.
Estimated period [s]: 50
I'm trying to find the peak frequency for two signals 'CA1' and 'PFC', within a specified range (25-140Hz).
In Matlab, so far I have plotted an FFT for each of these signals (see pictures below). These FFTs suggest that the peak frequency between 25-140Hz is different for each signal, but I would like to quantify this (e.g. CA1 peaks at 80Hz, whereas PFC peaks at 55Hz). However, I think the FFT is not smooth enough, so when I try and extract the peak frequencies it doesn't make sense as my code pulls out loads of values. I was only expecting a few values - one each time the FFT peaks (around 2Hz, 5Hz and ~60Hz).
I want to know, between 25-140Hz, what is the peak frequency in 'CA1' compared with 'PFC'. 'CA1' and 'PFC' are both 152401 x 7 matrices of EEG data, recorded
from 7 separate individuals. I want the MEAN peak frequency for each data set (i.e. averaged across the 7 test subjects for CA1 and PFC).
My code so far (based on Matlab help files and code I've scrabbled together online):
Fs = 508;
%notch filter
[b50,a50] = iirnotch(50/(Fs/2), (50/(Fs/2))/70);
CA1 = filtfilt(b50,a50,CA1);
PFC = filtfilt(b50,a50,PFC);
%FFT
L = length(CA1);
NFFT = 2^nextpow2(L);
%FFT for each of the 7 subjects
for i = 1:size(CA1,2);
CA1_FFT(:,i) = fft(CA1(:,i),NFFT)/L;
PFC_FFT(:,i) = fft(PFC(:,i),NFFT)/L;
end
%Average FFT across all 7 subjects - CA1
Mean_CA1_FFT = mean(CA1_FFT,2);
% Mean_CA1_FFT_abs = 2*abs(Mean_CA1_FFT(1:NFFT/2+1));
%Average FFT across all 7 subjects - PFC
Mean_PFC_FFT = mean(PFC_FFT,2);
% Mean_PFC_FFT_abs = 2*abs(Mean_PFC_FFT(1:NFFT/2+1));
f = Fs/2*linspace(0,1,NFFT/2+1);
%LEFT HAND SIDE FIGURE
plot(f,2*abs(Mean_CA1_FFT(1:NFFT/2+1)),'r');
set(gca,'ylim', [0 2]);
set(gca,'xlim', [0 200]);
[C,cInd] = sort(2*abs(Mean_CA1_FFT(1:NFFT/2+1)));
CFloor = 0.1; %CFloor is the minimum amplitude value (ignore small values)
Amplitudes_CA1 = C(C>=CFloor); %find all amplitudes above the CFloor
Frequencies_CA1 = f(cInd(1+end-numel(Amplitudes_CA1):end)); %frequency of the peaks
%RIGHT HAND SIDE FIGURE
figure;plot(f,2*abs(Mean_PFC_FFT(1:NFFT/2+1)),'r');
set(gca,'ylim', [0 2]);
set(gca,'xlim', [0 200]);
[P,pInd] = sort(2*abs(Mean_PFC_FFT(1:NFFT/2+1)));
PFloor = 0.1; %PFloor is the minimum amplitude value (ignore small values)
Amplitudes_PFC = P(P>=PFloor); %find all amplitudes above the PFloor
Frequencies_PFC = f(pInd(1+end-numel(Amplitudes_PFC):end)); %frequency of the peaks
Please help!! How do I calculate the 'major' peak frequencies from an FFT, and ignore all the 'minor' peaks (because the FFT is not smoothed).
FFTs assume that the signal has no trend (this is called a stationary signal), if it does then this will give a dominant frequency component at 0Hz as you have here. Try using the MATLAB function detrend, you may find this solves your problem.
Something along the lines of:
x = x - mean(x)
y = detrend(x, 'constant')