I need a good tutorial that will explain on how to setup a ssh connection via a direct ethernet connection to a Raspberry Pi with a static IP running Arch Linux. I have tried a few but all seem to fail. Any Suggestions?
What kind of ethernet connection? Do you have a crossover cable? If yes you can connect it directly to your computer and assign it an IP address. If not, you can connect your Pi to the same router as your computer is connected to, and install nmap on your machine. You can run the following command to identify your raspberry pi's IP address (assuming your router assigns IP addresses in 192.168.1.x space):
nmap -sn 192.168.1.1/24
The Raspberry Pi will show up with its ethernet MAC address and most likely also that the address belongs to RPI foundation. You can then ssh into it.
Related
I have the following setup:
Ubuntu 18.04 PC connected with an ethernet cable to a raspberry pi 3+.
What I want:
I am using ssh to connect to the Pi. I would like that the Pi can get internet access through the ethernet. Meaning, that the Pi is using the internet of the PC.
It would be nice if you could help me with a guide and tell me what I have to change in order to make it work.
What I tried:
I have a static IP on my PC as well as on the Pi.
In the network manager (nm-connection-editor), I set the IPv4 method to 'Shared to other computers'.
How do I now tell the Pi to use this network?
Thanks for your help
I have a raspberry pi 3 connected to my PC (Windows 7) via ethernet using DHCP server and VNC viewer and it works perfectly.
The pc is connected to a WIFI.
I want to access to internet from my raspberry pi, I tried the ICS sharing but it didn't work:
I shared the wifi connection:here
changed the ip address: here
after sharing the wifi connection, I am unable to access internet from both the pc and rasp even though they are in the same ip address.
On PC,On the Rasp
Can you please help me to find a solution?
Thank you.
You have to create a network bridge.
Select the two networks, right click and select bridge connections.
I'd use static IP address on your PI and your PC's ethernet
I have install OS in SD card and after installation OS is boot successfully but display below message every time:
http://prntscr.com/fbhj3j
I did not connect LAN cable raspberry board.
If this issue is because I cannot connect internet using wifi? If yes, how?
You need to continue to follow the instructions here: https://developer.android.com/things/hardware/raspberrypi.html
A Raspberry Pi will not connect to the Wifi if you have not first connected to an ethernet lan cable first. (Once you are connected via ethernet you then can configure the wifi and finally remove the ethernet cable).
So you are up to this step:
Connect an Ethernet cable to your local network.
When this is connected, your screen will show the IP address of the Raspberyy Pi on your local network
I want to install MATLAB and Simulink support package for Raspberry Pi. I follow this link to do . I directly connect my laptop with Raspberry Pi using Ethernat cable.
But i didn't get output.
while installing i got error - "Could not detect a Raspberry Pi board on "Local Area Connection". Check your Ethernet connection to Raspberry Pi.
The FDX/LNK/100 LEDs on the Raspberry Pi board should be illuminated.
For network trouble-shooting instructions see http://www.mathworks.com">The MathWorks Web Site"
Can anyone help to solve this problem?
I have also experienced your same issue but after proceeding in this way I solved it.
Before you put the SD card on the Raspberry Pi you need:
power off the Pi
connect the Ethernet cable to the host computer
finally power on the Pi
In addition you may take a look at this troubleshooting guide.
Try the following steps.
1. Open cmd and execute 'ipconfig'
check for a network interface with '169.x.x.x' ip address
If there is one, you could access your Pi via IP 169.254.0.2
If there is none, check if your Ethernet port is enabled and no static IP is configured.
The above steps make sure that your Ethernet port is in proper state.
Repeat the hardware setup with direct connection in the network settings.
I have just installed Raspbian on my Raspberry Pi and I booted it up with it attached to a monitor, keyboard, and ethernet. I can successfully log in, but when I run ifconfig, it only shows the lo interface (eth0 does not show up at all). It is plugged into the router via ethernet and the lights by the ethernet outlets are on for both the router and the raspberry pi. It also does not show up as a connected device on the router admin screen.
Since this is a new Pi, I'm not sure if the problem is hardware or software, do I need to do anything special to connect it to ethernet?
ifconfig -a
should return all the interface available in your system( generally speaking), you will see eth0 which is down, to bring it up:
ifconfig eth0 up
then you can configure eth0 either manually or using dhcp.