I want to connect my S6 with Rj45 to otg cable. I have connected several time with Ethernet cable with not working.
How to enable this option in S6.
OTG cable is based on USB protocol whereas, RJ45 has MAC controller and the communication protocol used is called ethernet. So what you are saying won't work unless you interoperability these two physical mediums and protocols, connect something like this:
Related
I'm working on a project where I need two raspberry pis to communicate and the ethernet port is not free, I'm not allowed to make any changes to the GPIO pins, and I'm forced to use the USB port due to hardware considerations. Is it possible for them to communicate using a direct USB cable, or perhaps using two USB-RS232 cables?
Thanks!
Siddharth
I would use the TTL serial pins on the GIO header. See https://elinux.org/images/1/13/Adafruit-connection.jpg
You could create your own simple null modem serial cable - consisting of 3 jumper cables.
Connect pins
6 <--> 6
8 <--> 10
10 <--> 8
If you can't use the GPIO header - you can do a USB to USB connection using USBNET. http://www.linux-usb.org/usbnet/
Is it possible for them to communicate using a direct USB cable, or perhaps using two USB-RS232 cables?
You fail to mention exactly which Raspberry Pi version(s) you are using.
Only the Raspberry PI Zero can be used as a USB Gadget.
Since USB is a master-slave(s) interface & protocol, you cannot simply connect two Raspberry PI 1/2/3 boards together using USB, because that would be a master-to-master connection.
If you look hard enough for a (passive) USB Type A (male) to Type A (male) cable, you can find them, but it's a bogus connection that will not work.
There are active USB host-to-host cables (which contain a shared gadget), but support can be an issue.
You could connect a Raspberry PI 1/2/3 to a Raspberry PI Zero by USB, so long as the Zero's USB port was configured as a USB ACM CDC gadget.
However one simple solution is your alternative of installing USB-to-RS232 adapters to each board. A null-modem cable of three wires would suffice unless you needed hardware flow-control.
An alternative solution is installing USB-to-Ethernet adapters to each board (with static IP addresses, i.e. an ad-hoc connection). This approach provides a much faster connection than an RS-232 link, and is easily utilized by applications.
I have install OS in SD card and after installation OS is boot successfully but display below message every time:
http://prntscr.com/fbhj3j
I did not connect LAN cable raspberry board.
If this issue is because I cannot connect internet using wifi? If yes, how?
You need to continue to follow the instructions here: https://developer.android.com/things/hardware/raspberrypi.html
A Raspberry Pi will not connect to the Wifi if you have not first connected to an ethernet lan cable first. (Once you are connected via ethernet you then can configure the wifi and finally remove the ethernet cable).
So you are up to this step:
Connect an Ethernet cable to your local network.
When this is connected, your screen will show the IP address of the Raspberyy Pi on your local network
We have a shared PC in our LAB, connected to a Vector Network Analyzer (VNA). The PC communicates with the VNA through GPIB port, using Matlab functions. For my work, i need to acquire real-time data from the VNA into my own PC, which is few meters away from the VNA PC. I dont want to have wireless solutions due to the interference that might happen. I intend to buy a USB data transfer cable to connect the Matlab. But i couldn't find in google any similar idea to do so. I was wondering is such a solution practical? Does anybody has the same experience? And will be any problem regarding the drivers?
in USB bus systems there can only be one USB host all other devices are in USB device mode.in most cases the USB controllers of PCs are not capable of USB device mode, they all want to be USB host. in other bus systems like I2C this is called master-slave architecture
if you are lucky one of your PCs can be set to device mode and in this case this will work but your chances are very slim (because of the problem with the USB host and USB device mode)
https://unix.stackexchange.com/questions/195765/is-usb-to-usb-data-transfer-between-two-linux-oses-possible
a better solution would be to use ethernet
there are also modules in MATLAB for real-time communication over ethernet (Real-Time Transmit and Receive over Ethernet)
if your pcs have unused ethernet ports use an ethernet crossover cable (http://en.wikipedia.org/wiki/Ethernet_crossover_cable) and connect the pcs (i.e. http://www.ccm.net/faq/6340-connect-pcs-using-a-crossover-ethernet-cable)
else use an ethernet switch (or hub) to establish the ethernet communication between the pcs
beside MATLAB for communication you can use i.e. ssh or install a vnc server on one of the machines and remote-control it with a vnc client on the other,...
USB
with USB-to-ethernet adapters (ebay,...) you can use ethernet over usb when connecting the usb-to-ethernet adapters via a ethernet crossover cable
another possibility is to use two USB-to-serial adapters and connect them with a RS-232 crossover cable and then use RS-232 protocol for communication (putty,...)
Can I plug a cisco SPA303 ip phone directly into the ethernet port of a raspberry pi running raspbx?
I have got raspbx setup and running using a wifi dongle to connect to the router. The system works with the Cisco phone plugged into the router. However, the router is on the other-side of my house and ideally, as the raspbx is wifi, I would like to plug the phone directly into the pi and have it as one unit I can have anywhere in the house.
I have spent a painful amount of hours trying to set this up and I am sure there is a simple fix I am overlooking. Any ideas would be greatly appreciated.
Yes, you can. But you should setup static ip on phone or setup dhcpd server on RPi
Also some cisco phones have double ports(internal simpler switch inside). If so, you can connect one-by-one upto 8 phones.
There are several layers to take into consideration:
Link layer MDI/MDI-X detection of crossover/patch ethernet cable detection.
Static IP address for Raspberry Pi and a DHCP server for the IP phone
TFTP server to provisionize the IP phone
A peer in asterisk for the IP phone
I bought a new Arduino Ethernet Shield and hooked it to the Arduino Uno.
I am trying to set the IP address of the device to 192.168.1.177 tried File-> Examples -> Ethernet-> Webserver.
When I upload this - I get a "server is a 0.0.0.0'message in serial monitor !
My IP is set to 192.168.1.177 and setup a mac address of 0xB8, 0x27, 0xEB, 0x98, 0x46, 0x61 in the webserver code.
Appreciate any help in setting this IP address. ( I tried other combinations as well )
The Arduino Ethernet shield is mounted on the Arduino Uno, and connections are lined up .
i fix this problem by pressing firmly the shield to the board
This can manifest from many different causes. I ran into this and figured out that in my case, my the USB port + cable were not allowing sufficient power to the Ethernet chip.
I have 3 cables, 6in, 3ft, and 6ft. Only the 6" one had sufficiently low voltage drop to power the shield.
I honestly couldn't believe it, but there was a 0.1V drop between the 6in and the 6ft cables. When plugged into A USB 3.0 port with the Arduino loaded, I measured ~4.5V for the working 6in cable vs ~4.4V for the non-working 6ft cable.
I have 3 types of USB ports: 1.1, 2.0, and 3.0. Only the USB 3.0 ports provided enough power to power the shield. Thus for my case, I had to use the shortest USB cable on the 3.0 port.
When the Arduino's 5V rail was sufficiently sagging, the 3.3 Linear Regulator entered dropout mode and on all the non-working configurations I saw ~3.1V on the Ethernet shield's 3.3V rail, which is apparently sufficient to cause this symptom.