I've worked a tad with IOT on Raspberry pi before, but as a student I ran into a problem and was hoping someone could answer my question. So I need to run Windows IOT Core on the Raspberry Pi 3 (if it was up to me I'd use raspbian or some other flavor of linux, but it's not up to me) and I need to run it at a school who's network I don't have access to. Is there any way of running IOT on raspberry Pi without an internet connection. I had read somewhere that I could buy a router (and even though there was no internet connected to it) I could run ethernet from the router to my laptop and another from the router to the raspberry pi and ssh into the pi from my laptop. Is this true? and how would I go about ssh-ing into the pi? OR is there a better/alternative solution to running IOT with no internet?
You can directly connect Raspberry Pi to your laptop with the network cable. Then the Raspberry Pi will get an IP address. With this IP address, you can either debug app with Visual Studio or connect to the Raspberry Pi via SSH. There are some tools like IoT Dashboard or Device Portal you may need.
For more information about connecting Windows 10 IoT Core, you can reference Windows 10 IoT documentation->Connect your device.
Related
I have the following setup:
Ubuntu 18.04 PC connected with an ethernet cable to a raspberry pi 3+.
What I want:
I am using ssh to connect to the Pi. I would like that the Pi can get internet access through the ethernet. Meaning, that the Pi is using the internet of the PC.
It would be nice if you could help me with a guide and tell me what I have to change in order to make it work.
What I tried:
I have a static IP on my PC as well as on the Pi.
In the network manager (nm-connection-editor), I set the IPv4 method to 'Shared to other computers'.
How do I now tell the Pi to use this network?
Thanks for your help
I am new to Home Assistant and I currently have a disc image of the software installed on a Raspberry Pi 3b. I have managed to get this up and running successfully by connecting my PI to an internet connection via an ethernet cable and connecting my laptop to the same network wirelessly. The problem I am facing is that I wish to run this locally without an internet connection and simply connecting my laptop to the PI with the Ethernet cable does not seem to be working. I have tried looking around for support but I cannot seem to find much on the matter.
Home Assistant's default port is 8123 not 8023.
If there is a direct connection between your laptop and the Raspberry Pi then the chance is high that mDNS won't not work. Thus, homeassistant.local is not reachable.
Add a static IP address for your Home Assistant host and your laptop.
I want to install MATLAB and Simulink support package for Raspberry Pi. I follow this link to do . I directly connect my laptop with Raspberry Pi using Ethernat cable.
But i didn't get output.
while installing i got error - "Could not detect a Raspberry Pi board on "Local Area Connection". Check your Ethernet connection to Raspberry Pi.
The FDX/LNK/100 LEDs on the Raspberry Pi board should be illuminated.
For network trouble-shooting instructions see http://www.mathworks.com">The MathWorks Web Site"
Can anyone help to solve this problem?
I have also experienced your same issue but after proceeding in this way I solved it.
Before you put the SD card on the Raspberry Pi you need:
power off the Pi
connect the Ethernet cable to the host computer
finally power on the Pi
In addition you may take a look at this troubleshooting guide.
Try the following steps.
1. Open cmd and execute 'ipconfig'
check for a network interface with '169.x.x.x' ip address
If there is one, you could access your Pi via IP 169.254.0.2
If there is none, check if your Ethernet port is enabled and no static IP is configured.
The above steps make sure that your Ethernet port is in proper state.
Repeat the hardware setup with direct connection in the network settings.
Got a Raspberry Pi 2 running Raspbian which shares its PPPoE Ethernet connection via Wi-Fi (basically, serves as a geeky home access point).
Is it possible to obtain this setup using Windows 10 IoT?
I heard you can do it with the right Wifi adapter (Windows 10 Iot drivers are limited):
http://mtaulty.com/CommunityServer/blogs/mike_taultys_blog/archive/2015/08/22/windows-10-iot-core-on-raspberry-pi-2-using-an-internet-shared-connection.aspx
I'm on a network where I need my Raspberry Pi to be windows authenticated in order to reach out of the network or to connect to any intranet sites. Due to this I can't even test my WebView component properly other than sending html directly to WebView.NavigateToString().
My question is how do I set up Windows Authentication in Windows 10 IoT for Raspberry Pi?