I know how to show expanded macro in C.
However, I am interested in how to show a calculated value of a macro.
Precompiler definitely calculates macro values in order to do #if(a>b) statement:
#define STRINGIFY(s) XSTRINGIFY(s)
#define XSTRINGIFY(s) #s
#define ONE_BYTE_Tx_Time 11
#define NUM_OF_BYTES 16
#define BUSY_TIME 132
#define TOTAL_TIME 300
#define AVAIL_TIME (TOTAL_TIME-BUSY_TIME)
#define RESP_TIME (ONE_BYTE_Tx_Time * NUM_OF_BYTES)
#pragma message ("AVAIL_TIME =" STRINGIFY(AVAIL_TIME))
#pragma message ("RESP_TIME =" STRINGIFY(RESP_TIME))
#if (AVAIL_TIME <= RESP_TIME)
#error "not enough time"
#endif
The output during compilation is:
AVAIL_TIME =(300-132)
RESP_TIME =(11 * 16)
fatal error C1189: #error : "not enough time"
So, precompiler had calculated two integers, compared them and outputted an error.
My question is:
how to show actual RESULT of macro calculation during compilation?, i.e.
AVAIL_TIME = 168 // which is (300-132)
RESP_TIME = 176 // which is (11 * 16)
The formulas expansion can be rather complicated, so it is useful to see result during compilation, without running of the code:
AVAIL_TIME_in_SysTicks =(((75000000/1000000) * (1000000/2500)) - 2 * ((((75000000/1000000) * ((1000000000/900000) + 1)*(10 + 0x00000000/0x00000008) + 2)/1000) * 16))
Thanks, Igor
Related
Judging by this Print numeric value of a define that's based on other macros via pragma message? , what I want is likely not possible; then again, I'm not doing arithmetic here - so here is my example:
#include <stdio.h>
enum my_sizes { SIZE_BITS_8 = 0, SIZE_BITS_16 = 1, SIZE_BITS_32 = 2 };
#define XSTR(x) STR(x)
#define STR(x) #x
#define CHOSEN_SIZE_BITS SIZE_BITS_32
#define CHOSEN_SIZE_BYTES \
( CHOSEN_SIZE_BITS==SIZE_BITS_8 ? 1 \
: CHOSEN_SIZE_BITS==SIZE_BITS_16 ? 2 \
: CHOSEN_SIZE_BITS==SIZE_BITS_32 ? 4 \
: 0 )
#pragma message( "CHOSEN_SIZE_BITS " XSTR(CHOSEN_SIZE_BITS) " CHOSEN_SIZE_BYTES " XSTR(CHOSEN_SIZE_BYTES) )
int main() {
printf("Hello, world! bytes: %d!\r\n", CHOSEN_SIZE_BYTES);
return 0;
}
In https://replit.com/languages/c, this produces:
> clang-7 -pthread -lm -o main main.c
main.c:14:9: warning: CHOSEN_SIZE_BITS SIZE_BITS_32
CHOSEN_SIZE_BYTES ( SIZE_BITS_32==SIZE_BITS_8 ? 1 :
SIZE_BITS_32==SIZE_BITS_16 ? 2 :
SIZE_BITS_32==SIZE_BITS_32 ? 4 : 0 )
[-W#pragma-messages]
#pragma message( "CHOSEN_SIZE_BITS " XSTR(CHOSEN_SIZE_...
^
1 warning generated.
> ./main
Hello, world! bytes: 4!
>
What I wanted instead, was the printout of pragma message to be:
main.c:14:9: warning: CHOSEN_SIZE_BITS 2 CHOSEN_SIZE_BYTES 4
Note that XSTR would have expanded CHOSEN_SIZE_BITS to a number, in case it was defined via #define CHOSEN_SIZE_BITS 2, but it seemingly doesn't if an enum value is used in the define; and of course, the whole ternary expression is included in the pragma message printout - even if the C printout (via printf) confirms that the CHOSEN_SIZE_BYTES does indeed end up with the expected value 4.
So, is it somehow possible to get the printout that I want from the above macros - and if so, how?
To calculate something in preprocessor you have to calculate it in preprocessor. Ternary is evaluated at runtime. In preprocessor you have macro expansions and ## operator and then some more macro expansions and ## operator. Nothing more.
The following code:
#define SIZE_BITS_8 0
#define SIZE_BITS_16 1
#define SIZE_BITS_32 2
#define XSTR(x) STR(x)
#define STR(x) #x
#define BITS_TO_BYTE_0() 1
#define BITS_TO_BYTE_1() 2
#define BITS_TO_BYTE_2() 4
#define BITS_TO_BYTE_IN(SIZE_BITS) \
BITS_TO_BYTE_##SIZE_BITS()
#define BITS_TO_BYTE(SIZE_BITS) \
BITS_TO_BYTE_IN(SIZE_BITS)
#define CHOSEN_SIZE_BITS SIZE_BITS_32
#define CHOSEN_SIZE_BYTES BITS_TO_BYTE(CHOSEN_SIZE_BITS)
#pragma message( "CHOSEN_SIZE_BITS " XSTR(CHOSEN_SIZE_BITS) " CHOSEN_SIZE_BYTES " XSTR(CHOSEN_SIZE_BYTES) )
Outputs the following diagnostic on GCC:
<source>:22:9: note: '#pragma message: CHOSEN_SIZE_BITS 2 CHOSEN_SIZE_BYTES 4'
22 | #pragma message( "CHOSEN_SIZE_BITS " XSTR(CHOSEN_SIZE_BITS) " CHOSEN_SIZE_BYTES " XSTR(CHOSEN_SIZE_BYTES) )
I'm having quite a trouble finding the reason for my current hardfault.
I'm using freertos with static memory allocation (no malloc ever used) I use new with pre-allocated buffers (new (&buffer).
I have made sure that all threads are aligned(4).
whenever I use a form of printf, my application jumps to the hardfault from the freertos call "start the first task".
I write "embedded C++" code, what is basically C89 with namespaces and classes, so nothing other than is included from c++. each includes from c files (.h) are wrapped with extern "C" so there is never ever a linkage issue.
I have tested with newlib, newlib nano and the tinyprintf from spare time libs. no difference.
also, I have never an assert failure on the malloc calls, so I am "quite" sure no newlib function accesses malloc (am I right here?)
the internet suggests its either a dynamic memory allocation issue or a stack issue. how can I prove what is causing the hardfault? I believe the hint my stack gets corrupted because of my printf calls isn't that wrong. how can I prove this? (i have never debugged stacks and would need some help debugging the stack pointer).
any other ideas?
thank you very much
example:
(void) vsnprintf( _log_buffer, C_LOG_BUFFER_SIZE, format, args ); // hardfault
(void) sprintf( _log_buffer, "huhu" ); // no hardfault
dynamic allocation overwrites:
__ATL_LINK_EXTERN_C void *malloc( size_t size )
{
(void) size;
atl::os::assert::failed((char*)__FILE__,__LINE__);
return NULL;
}
__ATL_LINK_EXTERN_C void * calloc(size_t size1, size_t size2)
{
(void) size1;
(void) size2;
atl::os::assert::failed((char*)__FILE__,__LINE__);
return NULL;
}
__ATL_LINK_EXTERN_C void *realloc(void * ptr, size_t size)
{
(void) ptr;
(void) size;
atl::os::assert::failed((char*)__FILE__,__LINE__);
return NULL;
}
__ATL_LINK_EXTERN_C void free( void * ptr )
{
(void) ptr;
atl::os::assert::failed((char*)__FILE__,__LINE__);
}
freertos config:
/*
FreeRTOS V9.0.0 - Copyright (C) 2016 Real Time Engineers Ltd.
All rights reserved
VISIT http://www.FreeRTOS.org TO ENSURE YOU ARE USING THE LATEST VERSION.
This file is part of the FreeRTOS distribution.
FreeRTOS is free software; you can redistribute it and/or modify it under
the terms of the GNU General Public License (version 2) as published by the
Free Software Foundation >>!AND MODIFIED BY!<< the FreeRTOS exception.
***************************************************************************
>>! NOTE: The modification to the GPL is included to allow you to !<<
>>! distribute a combined work that includes FreeRTOS without being !<<
>>! obliged to provide the source code for proprietary components !<<
>>! outside of the FreeRTOS kernel. !<<
***************************************************************************
FreeRTOS is distributed in the hope that it will be useful, but WITHOUT ANY
WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS
FOR A PARTICULAR PURPOSE. Full license text is available on the following
link: http://www.freertos.org/a00114.html
***************************************************************************
* *
* FreeRTOS provides completely free yet professionally developed, *
* robust, strictly quality controlled, supported, and cross *
* platform software that is more than just the market leader, it *
* is the industry's de facto standard. *
* *
* Help yourself get started quickly while simultaneously helping *
* to support the FreeRTOS project by purchasing a FreeRTOS *
* tutorial book, reference manual, or both: *
* http://www.FreeRTOS.org/Documentation *
* *
***************************************************************************
http://www.FreeRTOS.org/FAQHelp.html - Having a problem? Start by reading
the FAQ page "My application does not run, what could be wrong?". Have you
defined configASSERT()?
http://www.FreeRTOS.org/support - In return for receiving this top quality
embedded software for free we request you assist our global community by
participating in the support forum.
http://www.FreeRTOS.org/training - Investing in training allows your team to
be as productive as possible as early as possible. Now you can receive
FreeRTOS training directly from Richard Barry, CEO of Real Time Engineers
Ltd, and the world's leading authority on the world's leading RTOS.
http://www.FreeRTOS.org/plus - A selection of FreeRTOS ecosystem products,
including FreeRTOS+Trace - an indispensable productivity tool, a DOS
compatible FAT file system, and our tiny thread aware UDP/IP stack.
http://www.FreeRTOS.org/labs - Where new FreeRTOS products go to incubate.
Come and try FreeRTOS+TCP, our new open source TCP/IP stack for FreeRTOS.
http://www.OpenRTOS.com - Real Time Engineers ltd. license FreeRTOS to High
Integrity Systems ltd. to sell under the OpenRTOS brand. Low cost OpenRTOS
licenses offer ticketed support, indemnification and commercial middleware.
http://www.SafeRTOS.com - High Integrity Systems also provide a safety
engineered and independently SIL3 certified version for use in safety and
mission critical applications that require provable dependability.
1 tab == 4 spaces!
*/
#ifndef FREERTOS_CONFIG_H
#define FREERTOS_CONFIG_H
/*-----------------------------------------------------------
* Application specific definitions.
*
* These definitions should be adjusted for your particular hardware and
* application requirements.
*
* THESE PARAMETERS ARE DESCRIBED WITHIN THE 'CONFIGURATION' SECTION OF THE
* FreeRTOS API DOCUMENTATION AVAILABLE ON THE FreeRTOS.org WEB SITE.
*
* See http://www.freertos.org/a00110.html.
*----------------------------------------------------------*/
/* USER CODE BEGIN Includes */
/* Section where include file can be added */
/* USER CODE END Includes */
/* Ensure stdint is only used by the compiler, and not the assembler. */
#if defined(__ICCARM__) || defined(__CC_ARM) || defined(__GNUC__)
#include <stdint.h>
extern uint32_t SystemCoreClock;
/* USER CODE BEGIN 0 */
extern void configureTimerForRunTimeStats(void);
extern unsigned long getRunTimeCounterValue(void);
/* USER CODE END 0 */
#endif
#define configUSE_PREEMPTION 1
#define configSUPPORT_STATIC_ALLOCATION 1
#define configSUPPORT_DYNAMIC_ALLOCATION 0
#define configUSE_IDLE_HOOK 1
#define configUSE_TICK_HOOK 1
#define configCPU_CLOCK_HZ ( SystemCoreClock )
#define configTICK_RATE_HZ ((TickType_t)1000)
#define configMAX_PRIORITIES ( 7 )
#define configMINIMAL_STACK_SIZE ((uint16_t)32) // MOD was 128
#define configMAX_TASK_NAME_LEN ( 32 ) // mod was 16
#define configGENERATE_RUN_TIME_STATS 1
#define configUSE_TRACE_FACILITY 1
#define configUSE_STATS_FORMATTING_FUNCTIONS 1
#define configUSE_16_BIT_TICKS 0
#define configUSE_MUTEXES 1
#define configQUEUE_REGISTRY_SIZE 8
#define configCHECK_FOR_STACK_OVERFLOW 1
#define configUSE_MALLOC_FAILED_HOOK 1
#define configUSE_DAEMON_TASK_STARTUP_HOOK 1
#define configUSE_PORT_OPTIMISED_TASK_SELECTION 1
/* Co-routine definitions. */
#define configUSE_CO_ROUTINES 0
#define configMAX_CO_ROUTINE_PRIORITIES ( 2 )
/* Software timer definitions. */
#define configUSE_TIMERS 1
#define configTIMER_TASK_PRIORITY ( 2 )
#define configTIMER_QUEUE_LENGTH 10
#define configTIMER_TASK_STACK_DEPTH 256
/* Set the following definitions to 1 to include the API function, or zero
to exclude the API function. */
#define INCLUDE_vTaskPrioritySet 1
#define INCLUDE_uxTaskPriorityGet 1
#define INCLUDE_vTaskDelete 1
#define INCLUDE_vTaskCleanUpResources 1
#define INCLUDE_vTaskSuspend 1
#define INCLUDE_vTaskDelayUntil 1
#define INCLUDE_vTaskDelay 1
#define INCLUDE_xTaskGetSchedulerState 1
#define INCLUDE_xTimerPendFunctionCall 1
#define INCLUDE_xQueueGetMutexHolder 1
#define INCLUDE_xSemaphoreGetMutexHolder 1
#define INCLUDE_pcTaskGetTaskName 1
#define INCLUDE_uxTaskGetStackHighWaterMark 1
#define INCLUDE_xTaskGetCurrentTaskHandle 1
#define INCLUDE_eTaskGetState 1
#define INCLUDE_xTaskAbortDelay 1
#define INCLUDE_xTaskGetHandle 1
/* Cortex-M specific definitions. */
#ifdef __NVIC_PRIO_BITS
/* __BVIC_PRIO_BITS will be specified when CMSIS is being used. */
#define configPRIO_BITS __NVIC_PRIO_BITS
#else
#define configPRIO_BITS 4
#endif
/* The lowest interrupt priority that can be used in a call to a "set priority"
function. */
#define configLIBRARY_LOWEST_INTERRUPT_PRIORITY 15
/* The highest interrupt priority that can be used by any interrupt service
routine that makes calls to interrupt safe FreeRTOS API functions. DO NOT CALL
INTERRUPT SAFE FREERTOS API FUNCTIONS FROM ANY INTERRUPT THAT HAS A HIGHER
PRIORITY THAN THIS! (higher priorities are lower numeric values. */
#define configLIBRARY_MAX_SYSCALL_INTERRUPT_PRIORITY 5
/* Interrupt priorities used by the kernel port layer itself. These are generic
to all Cortex-M ports, and do not rely on any particular library functions. */
#define configKERNEL_INTERRUPT_PRIORITY ( configLIBRARY_LOWEST_INTERRUPT_PRIORITY << (8 - configPRIO_BITS) )
/* !!!! configMAX_SYSCALL_INTERRUPT_PRIORITY must not be set to zero !!!!
See http://www.FreeRTOS.org/RTOS-Cortex-M3-M4.html. */
#define configMAX_SYSCALL_INTERRUPT_PRIORITY ( configLIBRARY_MAX_SYSCALL_INTERRUPT_PRIORITY << (8 - configPRIO_BITS) )
/* Normal assert() semantics without relying on the provision of an assert.h
header file. */
/* USER CODE BEGIN 1 */
#define configASSERT( x ) if ((x) == 0) {taskDISABLE_INTERRUPTS(); for( ;; );}
/* USER CODE END 1 */
/* Definitions that map the FreeRTOS port interrupt handlers to their CMSIS
standard names. */
#define vPortSVCHandler SVC_Handler
#define xPortPendSVHandler PendSV_Handler
/* IMPORTANT: This define MUST be commented when used with STM32Cube firmware,
to prevent overwriting SysTick_Handler defined within STM32Cube HAL */
/* #define xPortSysTickHandler SysTick_Handler */
/* USER CODE BEGIN 2 */
/* Definitions needed when configGENERATE_RUN_TIME_STATS is on */
#define portCONFIGURE_TIMER_FOR_RUN_TIME_STATS configureTimerForRunTimeStats
#define portGET_RUN_TIME_COUNTER_VALUE getRunTimeCounterValue
/* USER CODE END 2 */
/* USER CODE BEGIN Defines */
/* Section where parameter definitions can be added (for instance, to override default ones in FreeRTOS.h) */
/* USER CODE END Defines */
#endif /* FREERTOS_CONFIG_H */
And what does your debugger say? Did you check what is the actual HF, and where it occured? Do you have one handler for all possible HF? It makes debugging much more complicated - and write the proper ones, google "how to get stored register values from the stack when HF occurs" (http://www.freertos.org/Debugging-Hard-Faults-On-Cortex-M-Microcontrollers.html). When you have it all done you can start investigate it proper way.
Unfortunately the HF-s are difficult to diagnose the "lazy way". Some code writing is absolutely necessary .
I am trying to use &let in the beginning of my script to define a new macro variable... it should consist of equation from variables from dataset. The equation looks something like this, but SAS always gives me error like this (Runtime error was encountered, please see the log...).
The equation:
%let var_bad = (receivable_actual * 0.5) -
(EM_EVENTPROBABILITY * 0.02 * receivable_actual) +
((1 - EM_EVENTPROBABILITY) * 0.5 * (receivable_actual - amt_instalment));
Can you guys help me fix it?
Thanks,
Adam
#Jetzler: These are the errors it shows me in log.
ERROR 214-322: Variable name ( is not valid.
ERROR 22-7: Invalid option name -.
ERROR 23-7: Invalid value for the KEEP option.
---
23
1 ! (receivable_actual * 0.5) - (EM_EVENTPROBABILITY * 0.02 * receivable_actual) + ((1 - EM_EVENTPROBABILITY) * 0.5 * (receivable_actual - amt_instalment))
- -
214 22
ERROR 214-322: Variable name * is not valid.
ERROR 22-7: Invalid option name +.
1 ! (receivable_actual * 0.5) - (EM_EVENTPROBABILITY * 0.02 * receivable_actual) + ((1 - EM_EVENTPROBABILITY) * 0.5 * (receivable_actual - amt_instalment))
--- -
214 22
14338 + rename=(em_eventprobability = score_no_call));
-------
22 22
201 76
ERROR 214-322: Variable name 0.5 is not valid.
ERROR 22-7: Invalid option name *.
ERROR 22-322: Syntax error, expecting one of the following: a name, a quoted string, (, -, :, ;, END, INDSNAME, KEY, KEYS, NOBS, OPEN, POINT, DATA, LAST, NULL.
ERROR 201-322: The option is not recognized and will be ignored.
ERROR 76-322: Syntax error, statement will be ignored.
Why don't you just calculate the variable in the dataset and then select it into a macro variable?
Is there a way to check the type of variable by preprocessor ?
Actually I want to do something like this :
//test.c
int main(void)
{
TYPE a=6;
#if TYPE==int
printf("%d\n",a);
#elif TYPE==float
printf("%f\n",a);
#endif
}
Now I use it as :
gcc -o test -D TYPE=float test.c
But it is not working. TYPE is always matching with int and giving result according to %d.
Please help me to solve this problem.
Using a combination of techniques from the following links:
https://github.com/pfultz2/Cloak/wiki/C-Preprocessor-tricks,-tips,-and-idioms
http://jhnet.co.uk/articles/cpp_magic
#define CAT(a, ...) a ## __VA_ARGS__
#define SECOND(a, b, ...) b
#define IS_PROBE(...) SECOND(__VA_ARGS__, 0)
#define PROBE() ~, 1
#define NOT(x) IS_PROBE(CAT(_NOT_, x))
#define _NOT_0 PROBE()
#define BOOL(x) NOT(NOT(x))
#define IF(c) _IF(BOOL(c))
#define _IF(c) CAT(_IF_,c)
#define _IF_0(...)
#define _IF_1(...) __VA_ARGS__
#define IS_PAREN(x) IS_PROBE(IS_PAREN_PROBE x)
#define IS_PAREN_PROBE(...) PROBE()
#define IS_INT(t) IS_PAREN( CAT(_IS_INT_,t) (()) )
#define _IS_INT_int(x) x
#define IS_FLOAT(t) IS_PAREN( CAT(_IS_FLOAT_,t) (()) )
#define _IS_FLOAT_float(x) x
#define TYPE float
int main(void)
{
TYPE a=6;
IF(IS_INT(TYPE))(
printf("%d\n",a);
)
IF(IS_FLOAT(TYPE))(
printf("%f\n",a);
)
}
You can even test it out at https://godbolt.org/ with the -E compiler option.
The preprocessor can't compare strings like that. See this FAQ. The way to do it is by #defining the options, and there is an example there to help you.
I'm trying to get a third party audio library (STK) working inside Xcode. Along with the standard .h files, many of the implementation files include a file called SKINI.msg. SKINI.msg is in the same directory as all of the header files. The header files are getting included fine, but the compiler complains that it can't find SKINI.msg. What do I need to do to get Xcode to happily include SKINI.msg?
Edit: Here's the contents of SKINI.msg:
/*********************************************************/
/*
Definition of SKINI Message Types and Special Symbols
Synthesis toolKit Instrument Network Interface
These symbols should have the form:
\c __SK_<name>_
where <name> is the string used in the SKINI stream.
by Perry R. Cook, 1995 - 2010.
*/
/*********************************************************/
namespace stk {
#define NOPE -32767
#define YEP 1
#define SK_DBL -32766
#define SK_INT -32765
#define SK_STR -32764
#define __SK_Exit_ 999
/***** MIDI COMPATIBLE MESSAGES *****/
/*** (Status bytes for channel=0) ***/
#define __SK_NoteOff_ 128
#define __SK_NoteOn_ 144
#define __SK_PolyPressure_ 160
#define __SK_ControlChange_ 176
#define __SK_ProgramChange_ 192
#define __SK_AfterTouch_ 208
#define __SK_ChannelPressure_ __SK_AfterTouch_
#define __SK_PitchWheel_ 224
#define __SK_PitchBend_ __SK_PitchWheel_
#define __SK_PitchChange_ 49
#define __SK_Clock_ 248
#define __SK_SongStart_ 250
#define __SK_Continue_ 251
#define __SK_SongStop_ 252
#define __SK_ActiveSensing_ 254
#define __SK_SystemReset_ 255
#define __SK_Volume_ 7
#define __SK_ModWheel_ 1
#define __SK_Modulation_ __SK_ModWheel_
#define __SK_Breath_ 2
#define __SK_FootControl_ 4
#define __SK_Portamento_ 65
#define __SK_Balance_ 8
#define __SK_Pan_ 10
#define __SK_Sustain_ 64
#define __SK_Damper_ __SK_Sustain_
#define __SK_Expression_ 11
#define __SK_AfterTouch_Cont_ 128
#define __SK_ModFrequency_ __SK_Expression_
#define __SK_ProphesyRibbon_ 16
#define __SK_ProphesyWheelUp_ 2
#define __SK_ProphesyWheelDown_ 3
#define __SK_ProphesyPedal_ 18
#define __SK_ProphesyKnob1_ 21
#define __SK_ProphesyKnob2_ 22
/*** Instrument Family Specific ***/
#define __SK_NoiseLevel_ __SK_FootControl_
#define __SK_PickPosition_ __SK_FootControl_
#define __SK_StringDamping_ __SK_Expression_
#define __SK_StringDetune_ __SK_ModWheel_
#define __SK_BodySize_ __SK_Breath_
#define __SK_BowPressure_ __SK_Breath_
#define __SK_BowPosition_ __SK_PickPosition_
#define __SK_BowBeta_ __SK_BowPosition_
#define __SK_ReedStiffness_ __SK_Breath_
#define __SK_ReedRestPos_ __SK_FootControl_
#define __SK_FluteEmbouchure_ __SK_Breath_
#define __SK_JetDelay_ __SK_FluteEmbouchure_
#define __SK_LipTension_ __SK_Breath_
#define __SK_SlideLength_ __SK_FootControl_
#define __SK_StrikePosition_ __SK_PickPosition_
#define __SK_StickHardness_ __SK_Breath_
#define __SK_TrillDepth_ 1051
#define __SK_TrillSpeed_ 1052
#define __SK_StrumSpeed_ __SK_TrillSpeed_
#define __SK_RollSpeed_ __SK_TrillSpeed_
#define __SK_FilterQ_ __SK_Breath_
#define __SK_FilterFreq_ 1062
#define __SK_FilterSweepRate_ __SK_FootControl_
#define __SK_ShakerInst_ 1071
#define __SK_ShakerEnergy_ __SK_Breath_
#define __SK_ShakerDamping_ __SK_ModFrequency_
#define __SK_ShakerNumObjects_ __SK_FootControl_
#define __SK_Strumming_ 1090
#define __SK_NotStrumming_ 1091
#define __SK_Trilling_ 1092
#define __SK_NotTrilling_ 1093
#define __SK_Rolling_ __SK_Strumming_
#define __SK_NotRolling_ __SK_NotStrumming_
#define __SK_PlayerSkill_ 2001
#define __SK_Chord_ 2002
#define __SK_ChordOff_ 2003
#define __SK_SINGER_FilePath_ 3000
#define __SK_SINGER_Frequency_ 3001
#define __SK_SINGER_NoteName_ 3002
#define __SK_SINGER_Shape_ 3003
#define __SK_SINGER_Glot_ 3004
#define __SK_SINGER_VoicedUnVoiced_ 3005
#define __SK_SINGER_Synthesize_ 3006
#define __SK_SINGER_Silence_ 3007
#define __SK_SINGER_VibratoAmt_ __SK_ModWheel_
#define __SK_SINGER_RndVibAmt_ 3008
#define __SK_SINGER_VibFreq_ __SK_Expression_
} // stk namespace
And here's what the compiler said:
CompileC build/StkCompile.build/Debug-iphonesimulator/StkCompile.build/Objects-normal/i386/BandedWG.o "../../../Data/study/iPhone class/stk-4.4.2/src/BandedWG.cpp" normal i386 c++ com.apple.compilers.gcc.4_2
cd /Users/morganpackard/Desktop/trashme/StkCompile
setenv LANG en_US.US-ASCII
setenv PATH "/Developer/Platforms/iPhoneSimulator.platform/Developer/usr/bin:/Developer/usr/bin:/usr/bin:/bin:/usr/sbin:/sbin"
/Developer/Platforms/iPhoneSimulator.platform/Developer/usr/bin/gcc-4.2 -x c++ -arch i386 -fmessage-length=0 -pipe -Wno-trigraphs -fpascal-strings -fasm-blocks -O0 -Wreturn-type -Wunused-variable -D__IPHONE_OS_VERSION_MIN_REQUIRED=30000 -isysroot /Developer/Platforms/iPhoneSimulator.platform/Developer/SDKs/iPhoneSimulator3.1.2.sdk -fvisibility=hidden -fvisibility-inlines-hidden -mmacosx-version-min=10.5 -gdwarf-2 -iquote /Users/morganpackard/Desktop/trashme/StkCompile/build/StkCompile.build/Debug-iphonesimulator/StkCompile.build/StkCompile-generated-files.hmap -I/Users/morganpackard/Desktop/trashme/StkCompile/build/StkCompile.build/Debug-iphonesimulator/StkCompile.build/StkCompile-own-target-headers.hmap -I/Users/morganpackard/Desktop/trashme/StkCompile/build/StkCompile.build/Debug-iphonesimulator/StkCompile.build/StkCompile-all-target-headers.hmap -iquote /Users/morganpackard/Desktop/trashme/StkCompile/build/StkCompile.build/Debug-iphonesimulator/StkCompile.build/StkCompile-project-headers.hmap -F/Users/morganpackard/Desktop/trashme/StkCompile/build/Debug-iphonesimulator -I/Users/morganpackard/Desktop/trashme/StkCompile/build/Debug-iphonesimulator/include -I/Users/morganpackard/Desktop/trashme/StkCompile/build/StkCompile.build/Debug-iphonesimulator/StkCompile.build/DerivedSources/i386 -I/Users/morganpackard/Desktop/trashme/StkCompile/build/StkCompile.build/Debug-iphonesimulator/StkCompile.build/DerivedSources -include /var/folders/dx/dxSUSyOJFv0MBEh9qC1oJ++++TI/-Caches-/com.apple.Xcode.501/SharedPrecompiledHeaders/StkCompile_Prefix-bopqzvwpuyqltrdumgtjtfrjvtzb/StkCompile_Prefix.pch -c "/Users/morganpackard/Desktop/trashme/StkCompile/../../../Data/study/iPhone class/stk-4.4.2/src/BandedWG.cpp" -o /Users/morganpackard/Desktop/trashme/StkCompile/build/StkCompile.build/Debug-iphonesimulator/StkCompile.build/Objects-normal/i386/BandedWG.o
/Users/morganpackard/Desktop/trashme/StkCompile/../../../Data/study/iPhone class/stk-4.4.2/src/BandedWG.cpp:33:21: error: SKINI.msg: No such file or directory
/Users/morganpackard/Desktop/trashme/StkCompile/../../../Data/study/iPhone class/stk-4.4.2/src/BandedWG.cpp: In member function 'virtual void stk::BandedWG::controlChange(int, stk::StkFloat)':
/Users/morganpackard/Desktop/trashme/StkCompile/../../../Data/study/iPhone class/stk-4.4.2/src/BandedWG.cpp:326: error: '__SK_BowPressure_' was not declared in this scope
/Users/morganpackard/Desktop/trashme/StkCompile/../../../Data/study/iPhone class/stk-4.4.2/src/BandedWG.cpp:342: error: '__SK_AfterTouch_Cont_' was not declared in this scope
/Users/morganpackard/Desktop/trashme/StkCompile/../../../Data/study/iPhone class/stk-4.4.2/src/BandedWG.cpp:349: error: '__SK_ModWheel_' was not declared in this scope
/Users/morganpackard/Desktop/trashme/StkCompile/../../../Data/study/iPhone class/stk-4.4.2/src/BandedWG.cpp:357: error: '__SK_ModFrequency_' was not declared in this scope
/Users/morganpackard/Desktop/trashme/StkCompile/../../../Data/study/iPhone class/stk-4.4.2/src/BandedWG.cpp:359: error: '__SK_Sustain_' was not declared in this scope
/Users/morganpackard/Desktop/trashme/StkCompile/../../../Data/study/iPhone class/stk-4.4.2/src/BandedWG.cpp:363: error: '__SK_Portamento_' was not declared in this scope
/Users/morganpackard/Desktop/trashme/StkCompile/../../../Data/study/iPhone class/stk-4.4.2/src/BandedWG.cpp:367: error: '__SK_ProphesyRibbon_' was not declared in this scope
try:
using stk;
after includes
It is doubtful the compiler knows what to do with the files as the standard for the msg extension is Microsoft Outlook files.
Your problem might be that you have added them to the project when they don't need to be. For example, they might be readme files or some other form of human readable notes.
According to the Sythesis Toolkit site, the Skini.msg file:
The other important file used by SKINI
is SKINI.msg, which is a set of
defines to make C code more readable,
and to allow reasonably quick
re-mapping of control numbers, etc..
All of these defined symbols are
assigned integer values. For Java, the
defines could be replaced by
declaration and assignment statements,
preserving the look and behavior of
the rest of the code.
Usually such a file would be header (.h) in all versions of C. Try removing the .msg files from the project and see if it compiles. I'd check with their mail list to see how the files are usually handled. You might have to add a custom build script for them.
Could you post the text of the #includes, and the compiler invocation and error (just by dragging and dropping the "Compiling" and "Error" lines from the build log). You ought to be able to #include arbitrary files in C source.