For a fast ADC sampling USB device, I am using the USB 2.0 High Speed capable STM32F733 with the embedded USB-HS PHY. In USBView, I can see that the device is enumerated, the libusb code opens the device and claims interface, but when I try to receive data with libusb_bulk_transfer, the operation times out (return code -12). Things I have tried: I have confirmed than when I request data with libusb_bulk_transfer, the device is interrupted. Note: I have DMA enabled in my class configuration C file and it is not clear to me how that is triggered. I have verified that the transfersize and packet count registers are being set correctly by the LL library function, and that when I request data from
Any tips on debugging such problems will be much appreciated - this board is my undergrad thesis due in under two months!
Desktop sequence:
libusb_get_device_list, libusb_get_device_descriptor, libusb_open, libusb_get_string_descriptor_ascii, libusb_free_device_list, libusb_bulk_transfer(devh, fat_EPIN_ADDR, inframe, fat_EPIN_SIZE, &gotBytes, 100). Where gotBytes is integer, and inframe is a large array.
Device firmware:
MX_USB_DEVICE_Init();
uint8_t txBuffer[10*fat_EPIN_SIZE];
while (1)
{
USBD_LL_Transmit(&hUsbDeviceHS, Custom_fat_EPIN_ADDR, txBuffer, Custom_fat_EPIN_SIZE);
HAL_Delay(1);
}
Custom_fat_EPIN_SIZE is 0x200 and the endpoint address is 0x81 (EP IN 1)
Installed driver for device is WinUSB (verified in Device Manger to be winusb.sys), and I am linking libusb-1.0 into my desktop program. You can find my source code at https://gitlab.com/tywonemi-school-stuff/silicon-radar-fun, the firmware is My SW/v1 and the desktop software is a Qt Creator project in My SW/Viewer, of note is usb.cpp. You can also compare with testing project/HIDTest, which is code that I tested with STM32F303 nucleo dev board where I was able to read an array through IN bulk endpoint with the Viewer application. However, F3 has the USB peripheral, while F7 has OTG_USB, and I am now attempting USB 2.0 compliant HS so there may be more protocol-based pitfalls. You can also find the output of the device descriptor etc from USBView in my SW/USBView_broken.txt
EDIT 1: I have found finally some concrete error in the STM32 behavior. The DMAADDR is set for EPIN 0x81, and never increments, despite the DMA being enabled. I have went through literally every occurrence of the word "DMA" in the USB_OTG periphery.
I thought it might be that my linker script makes my array be stored in DTCM or similar, and the OTG DMA can't access it, but the address of txBuffer is 0x2003EBEC which is in SRAM2. The AHB matrix in the reference manual clearly shows, that the USB OTG HS DMA is master for a bus that SRAM2 is a slave of. And DTCM is connected too. I will look for application notes for USB OTG HS DMA - it just seems to be refusing to copy data!
I have fixed my issue by disabling the DMA setting. I have re-read the relevant portions of the reference manual and still don't know how exactly the values propagate into the Tx FIFOs. It is possible that DMA-less operation will be a major bottleneck in my project, I might return to this later.
Related
I am writing an operating system for the raspberry pi.
I have a problem with the sdcard driver for the custom sdhost controller (emmc2)
of the raspberry-pi 4 (Cortex-A72, ARMv8-A, bcm2711 chipset).
Without using sdma everything works. With sdma, read works, but after writing sectors, the data on the sdcard sometimes contains invalid data.
For the sdma data transfer, I use a transfer buffer with a device type memory attribute (nGnRnE). When I use a fresh data buffer for the dma write transfer, the data on the sdcard is correct. But when I reuse the same buffer for the next write, then the sector on the sdcard partially contains data from the previous buffer content.
Maybe this is a cache coherency problem. I have enabled all caches (I and D). In the ARM manuals there is a talk of the SCU (snoop control unit) and I don't know whether I have do bother about the SCU.
My questions are:
Is it necessary to enable the SCU on a Cortex-A72 and how can this be done ?
What other things have to be kept in mind when using dma for device access ?
I found the solution for my problem:
On the raspberry pi 4 (bcm2711 chip), the physical addresses that are written into the registers of a dma engine must be legacy master addresses. The legacy master addresses are in the range 0xC0000000-0xFFFFFFFF. So I have to add 0xC0000000 to the values of the physical addresses that are written into the registers of the sdhci controller.
The documentation can be found here:
https://datasheets.raspberrypi.org/bcm2711/bcm2711-peripherals.pdf
1.2. Address map
1.2.4. Legacy master addresses
The answer to the other SCU question is: it is not necessary to enable the SCU on the Raspberry Pi 4 when the caches are enabled.
I am having troubles using an I2C sensor with the Beagle Bone Black (BBB). The BBB is running a newly flashed 18.04 Ubuntu image specifically for the BBB.
I wired the sensor (VIN, GND, SCL, SDA) to the corresponding I2C2 pins (4, 2, 19, 20) on the BBB using the below pinout.
The sensor is supposed to be using address 0x40, but scanning I2C2 (using i2cdetect -r 2) does not show the sensor.
I have tested this with two separate sensors as I thought at first I may have fried the original sensor somehow, but the results are the same. In fact, running the I2C2 scan command yields the exact same results when nothing is connected at all.
I have read in many places that I2C2 may not be enabled by default, but I assume it is enabled in my case as I can scan I2C2 without getting an error. Is this assumption incorrect? Again, this is a freshly flashed BBB, and I have not enabled/disabled anything - it should be in the default state.
I have also verified the connectivity of my wires between the sensor and BBB. The voltage between VIN and GND on the chip is 3.3V, so it is definitely being powered.
Why can't I connect to my I2C sensors using the BBB?
it could be that the source you are using is outdated or not a viable entry for i2c.
Also, you could use this command to make sure i2c2 pins are available:
config-pin p9.21 i2c
config-pin p9.22 i2c
This may work, also. If this does not work, please reply with your entire source.
Seth
P.S. Also, if you have time, you may want to get an i2c library to use if your software falls short of setting up your own i2c library. They have smbus2 you can install with pip and other i2c libraries out there still.
Here are a few things you should check (in random order).
List all I2C buses wich i2cdetect -l and try them all. Depending on the platform, the i2c bus number in Linux may be different from the peripheral number used in the datasheet and pinout. E.g. "I2C2" might be bus i2c-1 or i2c-3 in Linux).
Use an oscilloscope or logical analyzer to see if the SCL and SDA lines are being driven. If they aren't check the bus number as above. If they are, then check whether the device gives an ACK; if it doesn't, anything else will never work: double-check the chip slave address. There are cheap logical analyzers that you can buy and user with pulseview.
Simply load the Linux driver for your chip (see the kernel docs on how to do it from userspace for a quick test). Then see check if the device appears or use dmesg to see any kernel error messages while probing.
I would like to read a block of data from my Arduino Mega (and also from an Arduino Micro in another project) with my Raspberry Pi via I2C. The code has to be in Perl because it's sort of a plug-in for my Home-Automation-Server.
I'm using the Device::SMBus interface and the connection works, I'm able to write and read single Bytes. I can even use writeBlockData with register address 0x00. I randomly discovererd that this address works.
But when I want to readBlockData, no register-address seems to work.
Does anyone know the correct register-address, or is that not even the problem that causes errors?
Thanks in advance
First off, which register(s) are you wanting to read? Here's an example using my RPi::I2C software (it should be exceptionally similar with the distribution you're using), along with a sketch that has a bunch of pseudo-registers configured for reading/writing.
First, the Perl code. It reads two bytes (the output of an analogRead() of pin A0 which is set up as register 80), then bit-shifts the two bytes into a 16-bit integer to get the full 0-1023 value of the pin:
use warnings;
use strict;
use RPi::I2C;
my $arduino_addr = 0x04;
my $arduino = RPi::I2C->new($arduino_addr);
my #bytes = $arduino->read_block(2, 80);
my $a0_value = ($bytes[0] << 8) | $bytes[1];
print "$a0_value\n";
Here's a full-blown Arduino sketch you can review that sets up a half dozen or so pseudo-registers, and when each register is specified, the Arduino writes or reads the appropriate data. If no register is specified, it operates on 0x00 register.
The I2C on the Arduino always does an onReceive() call before it does the onRequest() (when using Wire), so I set up a global variable reg to hold the register value, which I populate in the onReceive() interrupt, which is then used in the onRequest() call to send you the data at the pseudo-register you've specified.
The sketch itself doesn't really do anything useful, I just presented it as an example. It's actually part of my automated unit test platform for my RPi::WiringPi distribution.
I am using embedded Linux for the NIOS II processor and device tree. The GPIO functionality provides the ability to read and or write a single bit at a time. I have some firmware and PIOS that I want to read or write atomically by setting or reading all 32 bits at one time. It seems like there would be a generic device driver that if the device tree was given the proper compatibility a driver would exist that would allow opening the device and then reading and writing the device. I have searched for this functionality and do not find a driver. One existing in a branch but was removed by Linus.
My question is what is the Linux device tree way to read and write a device that is a general purpose 32 bit register/pio?
Your answer is SCULL
Character Device Drivers
You will have to write a character device driver with file operations to open and close a device. Read, write, ioctl, and copy the contents of device.
static struct file_operations query_fops =
{
.owner = THIS_MODULE,
.open = my_open,
.release = my_close,
.ioctl = my_ioctl
};
Map the address using iomem and directly read and write to that address using rawread and rawwrite. Create and register a device as follows and then it can be accessed from userspace:
register_chrdev (0, DEVICE_NAME, & query_fops);
device_create (dev_class, NULL, MKDEV (dev_major, 0), NULL, DEVICE_NAME);
and then access it from userspace as follows:
fd = open("/dev/mydevice", O_RDWR);
and then you can play with GPIO from userspace using ioctl's:
ioctl(fd, SET_STATE);
What is the Difference between BGAPI and BGScript ?
And if we write any code for BG profile than how can we burn it in BLE 112?
The BGAPI interface defines the protocol used to talk to the module over USB or serial link.
BGScript is something which runs on the module processor itself, when the USB or serial link is not used.
I have the dongle, BLED112, which is the same thing as BLE112 with a USB connector on it, and the code is "burned" to it using standard USB DFU interface.
The downloading of the code to BLE112 can be done using several methods:
(1) Bring out the DD, DC debug interface pins from your module and use the CC-Debugger (digikey part 296-30207-ND, $55). This works every time. If you have the DKBLE112 kit, the CC-Debugger fits on the 10-pin .050 connector in lower right corner. You can "burn" any firmware and any stack this way. Works awesome.
(2) Hope that the current firmware on the CC2540 has serial bootloader, and load the new firmware (hopefully also containing serial bootloader) using UART. TI has the tools, but it sure seems quite convoluted to me, and I did not try it.