Im aware that you can add an entry to the chart using the .addEntry as in
chartView.data?.addEntry(ChartDataEntry(value: y, xIndex: x), dataSetIndex: 0)
but if I do that on a line chart the line will continue drawing from the last entry no matter where in the xAxis I put this new entry, Is there a way to sort the entries after I add a new one so that wherever the new entry is in the xAxis I have a beautiful continuous line?
Related
I am creating a line chart with multiple lines. I am trying to disable the tooltip that pops up over one of the lines. Is it possible to disable the tool top for one of the lines, but not all of them?
This can be done by setting pointRadius and pointHitRadius to 0.
datasets:[{ data:[...], pointRadius: 0, pointHitRadius:0 }]
I use this key mapping to duplicate a line, and go to the same cursor position on this newly created line:
nnoremap , mqYp`qj
What this does:
Create mark 'q'
Yank line
Paste/put line (below current line, cursor is now at start of new line)
Go back to mark at previous line
Move one line down. (cursor is now on new line at the same place of start of previous line)
This works perfectly fine, however I see a flaw when putting a number in front of the command. Imagine I want to duplicate this line 10 times. It would try to create 10 marks basically. I could do Y10p for this, I do understand that. My problem with that approach is that I'm not on the same cursor position as I was in the first line, the one I'm duplicating.
So I'm looking for a way to do basically 10,, using my previously made mapping, and ending on the last line, at the same cursor position of where I was in the first line. Note that I am using IdeaVIM exclusively to code, which means I can't make any functions for this.
Is it possible to get this 10, working in this situation?
Edit #1:
Example text
# Start
# Initialize new variables
new_invoice_name_one = 'New Name One'
new_invoice_name_two = 'New Name Two'
new_invoice_address_one = 'New Address One'
Command executed: 3, with the cursor being on the first I of line 2
Desired output
# Start
# Initialize new variables
# Initialize new variables
# Initialize new variables
# Initialize new variables
new_invoice_name_one = 'New Name One'
new_invoice_name_two = 'New Name Two'
new_invoice_address_one = 'New Address One'
with the cursor being on the first I of line 5 `
Edit #2:
I see some potential at the LetHandler.java here, however I can not seem to figure out how to use it to match the use case. On the other hand, here it says it is not supported at all.
When I play vimgolf, I use a trick [count]#='... sometimes. It could be used for your requirement.
you can map:
nnoremap , #='mqYp`q'<cr>
Then you can just simple press 200, to achieve what you want.
You can achieve this by pasting to the above of current line. Do this nnoremap , YmqP`q
update
You cannot do that since vim's key mapping is just string concatenation. One way to achieve this is to predefine a macro. Put this in the related rc file,
let #q="mqYP`q"
nnoremap , #q
eclipse (ganymede) is not incrementing the line numbers automatically. On creating a new class it prints line number till 6 (6th line contains closing bracket for class). After writing new lines in class, line number is still 6. To get the line numbers updated I again have to go to... show line number -> uncheck it -> apply -> check it again-> apply.
which setting will allow auto incrementation of line number?
I an using JasperReports to download some content in pdf format. I fetched some data from the database and add a textField in the Detail band to show the entries of a particular column.
This is what I am getting
and if I add a line than pdf changed to
but my requirement is to show line between two entries.
I want to remove last line and the pdf should looks like
Put the line at the top of the detail band instead of the bottom, then change the printWhenExpression to $V{REPORT_COUNT}.intValue() != 1.
The line will then be printed before each entry except for the first one, essentially putting a line between each entry.
I want to draw a line in Crystal report. I can do that from a sub-menu but this line I need to draw in a Group section Field object with a background color property set to some color.
So whenever I draw a line it gets overlapped by this FieldObject.
How can I make sure that line would be visible over the background color of object?
Assuming you are doing this through the designer, you should just be able to right-click on your line and select "Move to Front".
Insert section below section that contains the FieldObject
Add line to new section
Format the first section (the one with the field object) as 'underlay following section(s)'