I have created a standalone application in Matlab, actually it works, it displays the desired output but it closes immediately, not even enough time to examine the output and read the error message on DOS (standalone mode) that says:
MATLAB:TooManyOutputs
Warning: 1 visible figure(s) exist at MCR Termination
If your application has terminated unexpectedly, please note that
applications generated by the MATLAB Compiler terminate when there are no
visible figure windows. See the documentation for WaitForFiguresToDie and
WAITFORCALLBACKS for more information.
Any help would be appreciated.
Looking at the first line of your message, TooManyOutputs suggests that you have an assignment somewhere of the form
[a b] = somefunction(parameters)
so you want the outputs of somefunction to be put in a and b, but somefunction only returns one parameter. This bug causes your program to terminate, and then MCR realizes the program exits without closing your figure window, causing the later error messages.
If I'm right about TooManyOutputs, you should already have that error message when running your code directly in Matlab; have you tried that before creating a standalone application?
If this doesn't help, you should probably post some of your code to make it clearer where the problem could come from.
Related
My DES model was working well till I've added a new function (just like many others added before) and the model gave me all these error messages:
I wonder what do these messages mean and what made all of them appear suddenly. I was running the model just before it without any errors. Is there a way I could get my model back? :)
Thank you.
Edit 1:
Here is the newly created function: Newly created function
Given that I've ignored it, and made all the callings of it as comments, then the errors were still appearing. I've closed this model version and opened a backup then created the same function and the whole scenario happened again with the same 94 errors.
Is there something I need to change in the function itself?
The function checks the number of agents in certain parts of the model to stop delay blocks accordingly. That's done by adding variables that increment on exiting of agents and get the difference between them.
Typically this is caused by a syntax error in the new function that you created. See if you ignore this and then compile if it gets fixed.
Most of the time the compiler is smart enough to show you the error, but often if you replace a { with [ or you leave out a { the compiler get very confused and gives you 100s of errors.
If yous still cant find the issue maybe paste the code of your new function in the question.
I am running a script which calls a function, and if a certain condition is met, inside the function, I want the whole thing just to terminate (and by that I do not mean I want to close matlab using exit). Is that possible? I know I can use return or break to return to the script, however I want the script to stop as well if this condition is met.
The only function I know of that does this is error. This throws an exception, and, if no exception handlers with try and catch are installed in the calling script, will terminate and return to command prompt. Which is what you want, as far as I understand. It prints an error message though. This could be suppressed if you guard all code in the top-level script with a try catch handler. However this will have to be specific to the one error and it makes debugging ("stop-on-error") much more difficult.
The thing is that the only use case I see for this behavior (termination of whole program on certain event) is when a non recoverable error occurs, and in that case printing an error message is indeed appropriate.
In case the script is successful termination of the whole program is not really the right way. All functions should return to give the upper layers of the code to perform some clean-up action, like saving the output data or so.
I'm working on a project based on the stm32f4discovery board using IAR Embedded Workbench (though I'm very close to the 32kb limit on the free version so I'll have to find something else soon). This is a learning project for me and so far I've been able to solve most of my issues with a few google searches and a lot of trial and error. But this is the first time I've encountered a run-time error that doesn't appear to be caused by a problem with my logic and I'm pretty stuck. Any general debugging strategy advice is welcome.
So here's what happens. I have an interrupt on a button; each time the button is pressed, the callback function runs my void cal_acc(uint16_t* data) function defined in stm32f4xx_it.c. This function gathers some data, and on the 6th press, it calls my void gn(float32_t* data, float32_t* beta) function. Eventually, two functions are called, gn_resids and gn_jacobian. The functions are very similar in structure. Both take in 3 pointers to 3 arrays of floats and then modify the values of the first array based on the second two. Unfortunately, when the second function gn_jacobian exits, I get the HardFault.
Please look at the link (code structure) for a picture showing how the program runs up to the fault.
Thank you very much! I appreciate any advice or guidance you can give me,
-Ben
Extra info that might be helpful below:
Running in debug mode, I can step into the function and run through all the lines click by click and it's OK. But as soon as I run the last line and it should exit and move on to the next line in the function where it was called, it crashes. I have also tried rearranging the order of the calls around this function and it is always this one that crashes.
I had been getting a similar crash on the first function gn_resids when one of the input pointers pointed to an array that was not defined as "static". But now all the arrays are static and I'm quite confused - especially since I can't tell what is different between the gn_resids function that works and the gn_jacobian function that does not work.
acc1beta is declared as a float array at the beginning of main.c and then also as extern float32_t acc1beta[6] at the top of stm32f4xx_it.c. I want it as a global variable; there is probably a better way to do this, but it's been working so far with many other variables defined in the same way.
Here's a screenshot of what I see when it crashes during debug (after I pause the session) IAR view at crash
EDIT: I changed the code of gn_step to look like this for a test so that it just runs gn_resids twice and it crashes as soon as it gets to the second call - I can't even step into it. gn_jacobian is not the problem.
void gn_step(float32_t* data, float32_t* beta) {
static float32_t resids[120];
gn_resids(resids, data, beta);
arm_matrix_instance_f32 R;
arm_mat_init_f32(&R, 120, 1, resids);
// static float32_t J_f32[720];
// gn_jacobian(J_f32, data, beta);
static float32_t J_f32[120];
gn_resids(J_f32, data, beta);
arm_matrix_instance_f32 J;
arm_mat_init_f32(&J, 120, 1, J_f32);
Hardfaults on Cortex M devices can be generated by various error conditions, for example:
Access of data outside valid memory
Invalid instructions
Division by zero
It is possible to gather information about the source of the hardfault by looking into some processor registers. IAR provides a debugger macro that helps to automate that process. It can be found in the IAR installation directory arm\config\debugger\ARM\vector_catch.mac. Please refer to this IAR Technical Note on Debugging Hardfaults for details on using this macro.
Depending on the type of the hardfault that occurs in your program you should try to narrow down the root cause within the debugger.
I have a question about inner Matlab error management. Right now I have quite a large program with a lot of variables and functions that cumulated over my code writting and I'm 100 percent sure that I did not catch all the bugs and mistakes in the program and I don't want it to crash completely when is used by layman user. So, is there a way to display errordlg message and for example restart the program when there will be any given error directly by Matlab (for example when I forgot to declare a global variable etc.)?
Thanks for answers, Peter
Crashes are good, because they force users to report bugs.
If you don't want to go that route, Matlab provides try-catch: wrap your code in a try-catch block. If there is an error, you'll find yourself in the catch block where you can have Matlab send you an email with the error message, and restart the program if necessary.
You can use try/catch statements to respond to errors in your program. There's more information here.
I have a wxWidgets/GTK based application that works well - except for one installation on an Debian Squeeze ARM system. There it crashes when the user just activates the main window of it. To find the reason for that I added a signal handler to the application and use libunwind out of that signal handler to find the source for the crash. During a test that worked fine, when the software writes e.g. to address 0x0 libunwind correctly points me to the function where that happens.
But the results for the system where the crash appears unexpectedly are a bit strange, they seem to happen outside of my application. One crash comes from a function with no name (here libunwind returns an empty string), and one is caused by "malloc_usable_size", a system function which should never die this way.
So...what to do next? All ideas, suggestions or any other hints are welcome since I'm not sure how to contunue with that problem...
Check for buffer overrun or overwriting some memory unexpectedly for any structures, pointers, memory locations for items returned by library functions.
Check for invalid pointer frees in your code for the library allocated pointers that you are using.
May be using valgrind would also help.