It sounds reasonable that the os/rtos would schedule an "Idle task". In that case, wouldn't it be power consuming? (it sounds reasonable that the idle task will execute: while (true) {} )
This depends on the OS and the CPU architecture. On x86 (Intel compatible) the operating system might execute HLT instructions, making the CPU wait until something interesting happens, such as a hardware interrupt. This supposedly consumes very little power. Operating systems report the time spent doing this as "idle" and may even assign it to a fictional "idle" process.
So, when in Windows task manager you see that the System Idle Process is consuming 90% CPU what it really means is that the CPU does not have an actual a program to run 90% of the time.
Here's a good article on the subject: What does an idle CPU do?
Historically it's been a lot of different schemes, especially before reducing power consumption in idle was an issue.
Generally there is an "idle" process/task that runs at the lowest priority and hence always gets control when there's nothing else to do. Many older systems would simply have this process run a "do forever" loop with nothing of consequence in the loop body. One OS I heard of would run machine diagnostics in the idle process. A number of early PCs would run a memory refresh routine (since memory needed to be cycled regularly or it would "evaporate").
(A benefit of this scheme is that 100% minus the % CPU used by the idle process gives you the % CPU utilization -- a feature that was appreciated by OS designers.)
But the norm on most modern systems is to either run a "halt" or "wait" instruction or have a special flag in the process control block that even more directly tells the processor to simply stop running and go into power-saving mode.
There's always code to run, the idle task is the code if there's nothing else. It may execute a special CPU instruction to power down the CPU until a hardware interrupt arrives. On x86 CPUs it's hlt (halt).
This answer is specific to Windows NT-based OS.
Idle thread functioality
Tasks may vary between architectures, but generally these are the tasks performed by idle threads:
Enable interrupts to allow pending interrupts be delivered
Disable interrupts (using STI or CLI instructions, more on wiki)
On the DEBUG (or checked) builds, query if a kernel debugger is attached and allow breakpoints if been requested
Handle deferred procedure calls
Check if there are any runnable threads ready for execution. If there is one, update the idle processor control block with a pointer to the thread
Check the queues of other processors, if possible schedule thread awaiting execution on the idle processor
Call a power management routine, which may halt a processor or downgrade CPU tick rate and do other similar power saving activities
Additional info
When there are no runnable threads for a logical processor, Windows executes a kernel-mode idle thread. There is only 1 Idle process that has as many idle threads as there are logical processors. So on a Quad core machine with 4 logical/physical processors, there will be 1 Idle process and 4 idle threads.
In Windows, Idle process has ID = 0, so do all the Idle threads. These objects are represented by standard EPROCESS/KPROCESS and ETHREAD/KTHREAD data structures. But they are not executive manager processes and threads objects. There are no user-land address space and no user-land code is executed..
Idle process is statically allocated at system boot time before the process manager and object manager are set up. Idle thread structures are allocated dynamically as logical processors are brought live.
Idle thread priority is set to 0. However, this value doesn't actually matter as this thread only gets executed when there are no other threads available to run. Idle thread priority is never compared with priority of any other threads.
Idle threads are also special cases for preemption. The idle thread main routine KiIdleLoop (implementation from reactos) performs several tasks that are not interrupted by other threads. When there are no runnable threads available to run on a processor, that processor is marked as idle in a processor control block. Then if a runnable threads arrives to the queue scheduled for execution, that thread's address pointer is stored in the NextThread pointer of the idle processor control block. During the run of an idle thread, this pointer address gets checked on every iteration inside a while loop.
Source: Windows Internals. M. Russinovich. 6-th edition. Part 1, p.453 - 456.
Related
I came across that the process ready for execution in the ready queue are given the control of the CPU by the scheduler. The scheduler selects a process based on its scheduling algorithm and then gives the selected process the control of the CPU and later preempts if it is following a preemptive style. I would like to know that if the CPU's processing unit is being used by the processor then who exactly preempts and schedules the processes if the processing unit is not available.
now , i want to share you my thought about the OS,
and I'm sorry my English is not very fluent
What do you think about the OS? Do you think it's 'active'?
no, in my opinion , OS is just a pile of dead code in memory
and this dead code is constituted by interrupt handle function(We just called this dead code 'kernel source code')
ok, now, CPU is execute process A, and suddenly a 'interrupt' is occur, this 'interrupt' may occured because time clock or because a read system call, anyhow, a interrupt is occur. then CPU will jump the constitute interrupt handl function(CPU jump because CPU's constitute is designed). As said previously, this interrupt handle function is the part of OS kernel source code.
and CPU will execute this code. And what this code will do? this code will scheduleļ¼and CPU will execute this code.
Everything happens in the context of a process (Linux calls these lightweight processes but its the same).
Process scheduling generally occurs either as part of a system service call or as part of an interrupt.
In the case of a system service call, the process may determine it cannot execute so it invokes the scheduler to change the context to a new process.
The OS will schedule timer interrupts where it can do scheduling. Scheduling can also occur in other types of interrupts. Interrupts are handled by the current process.
Since idle tasks are generally used to safely consume CPU time that is not required by other software, what would happen if there was no idle task? Would the RTOS just automatically create one? Also, what other purpose do idle tasks serve other than consuming time?
what would happen if there was no idle task? Would the RTOS just automatically create one?
I doubt there is any RTOS that would do that. If there would be no idle task, then the list of runnable tasks would be empty and the scheduler would probably crash. Generally the single most important reason for idle thread's existence is to make the list of runnable tasks "never empty". This simplifies the code of scheduler.
Also, what other purpose do idle tasks serve other than consuming time?
In some systems idle task can perform some low priority activities (for example some garbage collection). It can also switch the core to low-power mode, especially on embedded devices. In that case when the idle task is run it means that there is nothing more to do, so the core can be stopped and wait for the next event (hardware interrupt or timeout) without using too much power. When the next event arrives the core is awakened by hardware and the event is processed. Either some "normal" thread will start running, or - if there is still nothing more to do - idle thread will resume and again switch to low-power mode.
If the CPU clock is running, instructions must be executed; if there were no idle task, then your OS is broken. The idle loop is an intrinsic part of the RTOS, not a user task, so the RTOS does not need to "create one automatically".
A low priority user task that never yields will prevent the idle loop from running; which is not necessarily a good thing. Such a task is not the same thing as the idle loop. For one thing any CPU usage tools the RTOS supports would report 100% usage all the time if such a task eusted - execution of the idle loop is not included is CPU usage because the CPU is always ready to respond to any interrupt event when idle - the loop does not ever cause any ready task to be delayed.
The idle task, or "idle loop" is typically just that, and empty loop that the program counter is set to when there is nothing else to do. In some architectures the loop may include a "wait-for-interrupt" instruction that stops core execution (stops clocking the core) to reduce power consumption. Since any context switch necessarily requires an interrupt to occur, the processor can if WFI is supported just stop in this loop.
Some RTOS support user hooks for the idle loop; low-priority run-to-completion functions that can operate in the background in the idle loop context.
what other purpose do idle tasks serve other than consuming time?
Most commonly, it does two things:
1. Garbage(resource) collection or cleaning
2. Initiate steps to reduce power consumption
Consider this: When one task/process is running on a single processor system, another task has to wait for its turn till the first task is either suspended or terminates (depending on the scheduling algorithm).
Kernel also consists of various tasks that are using the using the same CPU to do OS related stuff - like scheduling, memory management, responding to system calls etc.
So when a kernel schedules a particular task/process to give it CPU time, does it relinquish its control over the CPU?ie does it momentarily stop? If not how does it continually keep on running to do all OS related tasks while the other process is running on CPU? Does the scheduler move aside to give the next task in line CPU and if so what brings the scheduler back to go on with further scheduling activities? This question is similar but it does not contain enough details -
How can kernel run all the time?
I am confused about this part and I cant understand how this would work.Can somebody please explain this in detail. It would be helpful if you could explain it with an example.
Yeah.. you should stop thinking of the OS kernel as a process and think of it instead of just code and data - a state-machine that processes/threads call in to in order to obtain specific services at one end, (eg. I/O requests) and drivers call in to at the other end to provide service solutions, (eg. I/O completion).
The kernel does not need any threads of execution in itself. It only runs when entered from syscalls, (interrupt-like calls from running user threads/processes), or drivers, (hardware interrupts from disk/NIC/KB/mouse etc hardware). Sometimes, such calls will change the set of threads running on the available cores, (eg. if a thread waiting for a network buffer becomes ready because the NIC driver has completed the action, the OS will probably try to assign it to a core 'immediately', preempting some other thread if required).
If there are no syscalls, and no hardware interrupts, the kernel does nothing because it is not entered - there is nothing for it to do.
What you are missing is that few operating systems these days have a monitor process as you are describing.
At the risk of gross oversimplification, operating systems run through exceptions and interrupts.
Assume you have two processes, P and Q. P is the running process and Q is the next to run. One way to switch processes is the system timer goes off triggering an interrupt. P switches to kernel mode and handles that interrupt. P runs the interrupt code handling the timer and determines that Q should run. P then saves its context and loads Q. At that moment, Q is the running process. The interrupt handler exits and picks up where Q was before.
In other words, process P becomes the kernel scheduler while the interrupt is being processed. Each process becomes the scheduler that loads the next process.
Another example, let us say that Q has queued a read operation to a disk. That operation completes and triggers an interrupt. P, the running process, enters kernel mode to handle the interrupt. P then processes Q's disk read operation.
Every system has IDLE task which will be running if no other tasks are ready to run.So my question is , can IDLE task sleep?. My understanding is if idle task sleep then there is a chance of no task is available for the cpu to run. Is my understanding correct? Can anyone provide some link which elaborate about this topic?
It could busy-loop at lowest priority, or loop around code that sets a low-power mode, or a loop around a 'halt' instruction that stops the core execution completely.
Sleep() is not approriate - the CPU has to enter a mode where it is unavailable to any other thread until an interrupt, and Sleep() does not perform that function.
Whatever the hardware supports.
As long as the CPU is able to respond to interrupt requests, any of the above would be fine.
I'm reading about scheduling, but I can't figure out how a scheduler regains control after it invokes code in the user space.
E.g. the scheduler passes the control to some app in the user space which does some infinite loop and no other hardware interrupt occurs on an one core chip. All documents talk about the scheduler regaining control and preemptivly interrupting the user process, but how does that work if the control is never passed back to the OS?
Question: Does the scheduler register with some clock in the CPU to be given control again after X msecs? Or is there some other trick? If no, what is the C function called to register for regular (or one time?) control regains?
On Windows the Sleep(0) "causes the thread to relinquish the remainder of its time slice to any other thread of equal priority that is ready to run". This forces the scheduler to gain control.
On Linux the sched_yield "causes the calling thread to relinquish the CPU". This also forces the scheduler to gain control.
And the scheduler also gains control by interrupts too. When a thread has consumed its quantum of CPU usage the scheduler reschedules.
Windows CE for example allows to customize the thread quantum.
You may also read Thread Scheduling: quanta, switching and scheduling algorithms.
There is no single scheduler in Windows. Event based scheduling code is spread across the kernel. The kernels dispatcher routines are triggered by these events:
Thread ready for execution
Thread quantum expired
Thread priority change
Thread processor affinity change
Wait functions and Sleep functions
This Microsoft presentation is summarizing some of the scheduler principles.
If no other interrupt occured, a preemptive O/S wouldn't despatch, and the user application would loop for ever.
This won't happen, though. Typically, a preemptive scheduler will despatch on every system call, every interrupt, and every tick of the system clock. The system clock will always interrupt, so your infinite loop simply won't occur.
The Pick operating system (after its developer Dick Pick) used a non-preemptive scheduler. Software developed for this system was required to make a system call periodically to allow the kernel to despatch other processes. In this environment the kernel would otherwise lose control completely until the process terminated.
The argument used in its justification was that considerable time was spent saving and restoring the processor state during a despatch. Forcing the application to take responsibility for this would allow a faster despatch process.