I would like to start a semester project related to Matlab Simulink and USRP devices. I am new in this field and studying regularly about it...
The first step to setup the devices is completed and now I would like to check if both device can communicate properly. For this Reason can any one suggest a simple Communication Module...
anything would be OK to start with. e.g sending text, Image, Voice, Video etc etc...
Regards
I suggest you take a look at the communications toolbox in matlab:
USRP® Support Package from Communications System Toolbox
There seem to be some code snippets for simulink available as well.
BR
Magnus
Related
I am using the RN4871 bluetooth module from microchip for sending sensor data to matlab. I programmed the module according to this website. www.allaboutcircuits.com
I was able to program the module through the serial monitor and also changed the name of the module to "RN4871_SAKIN".
Now I wanted to read the analog values from the characteristics UUID. For that I wanted to use matlab. I searched with the command "blelist" the available nearby BLE devices and found my device.
But when I try to connect to the device matlab gives me an error. I tried using ble("name") and ble("address") but both gave me the same error.
I dont think that matlab is the issue here. But I really dont know how to solve the problem. Going through the troubleshooting section in matlab was also not helpfull.
Matlab Failed to connect to device
Has someone experience connecting with this bluetooth module?
Cheers
I'd really love to learn to program cheap sensors and modules such as this one:
barometer sensor nRF51822 bluetooth module ibeacon LPS22HB, CR2032 battery holder, specifically to use within iOS and Swift.
I reached out to the company who makes them and tried researching how to get started multiple times, but I really can't figure out where to start. There are also pre-programmed modules, but my interest is programming these cheap ones to fit my needs.
I have the linked module, and a few others, and they appear and can be connected to using beacon detector apps, but display no understandable info.
I'd like to read the barometer pressure reading to start. Help is highly appreciated, I'd love to start working with these.
EDIT/UPDATE: I was able to read the modules manufacture name on one of many iBeacon scanner apps I tried and their name is Yunjia. With this information I am able to find alot more details online about what I have. One website says for these chips I can use LightBlue (the app I used to find the manufacturer name) to modify, read, and write to the module. Any additional advice is welcomed, I'll be researching and testing things out.
I also found the Schematics along with some additional info hidden in the seller website.
Edit 2: I found the manufactures little YouTube channel with some info, looks like I just have to do lots of research and testing and learn everything. https://www.youtube.com/channel/UCvqhWNqDE-v0je0X8XAEF2Q It contains some video instructions.
Edit 3: My short term goal of reading the barometer data was a success! After tons of digging I found I just had to write a value of 0x01 to turn on all sensors, then I was flooded with data and the barometer pressure in bytes which could be translated to the actual amount. Write 0x00 to trun off all sensors.
Apple's iBeacon framework is dirt-simple and very easy to use. It allows you to listen for beacons based a unique UUID, major id, and minor ID. It lets you know when a beacon enters or leaves range, and provides crude (immediate, near, medium, and far) distance values. You can create "beacon regions" that will notify your app when you enter or leave them. That's about it.
If you want to do something like read barometric pressure or temperature readings, you will need to either write your own low-level BLE code or use an existing library. My guess is that these modules are using very standard hardware and that you should be able to find libraries to read their specialized data.
Failing that, you will need specifications on their BLE interface and need to learn how to write Apple Core Bluetooth code. (The link you posted has zero specifications for the units. The only thing it provides is the numbers "nRF51822 bluetooth module ibeacon LPS22HB" (It's not in well-formed English so I don't know how to parse those descriptive terms. I'd google those numbers) Note that Core Bluetooth is a fairly low-level framework and not very easy to learn.
EDIT:
Googling "nRF51822", that is apparently an ARM based chip that includes radio hardware that supports BLE. It sounds like that is a general-purpose chip that vendor would use to build a BLE module. Given that, you'd probably have to reverse-engineer it to figure out how it works.
The "LPS22HB" appears to be a solid state pressure sensor that can be used to build a barometric pressure measurement device. It's no doubt interfaced with the "nRF51822". Without specs you're going to have a very hard time figuring out how it's interfaced however.
This semester I have a project where I need to send data from my microcontroller to my PC and read/interpret its data. We are doing this using an ftdi cable and using matlab to read the data.
I would like to know if there is a way that I can see if my matlab code works that doesn't involve me going to the lab to test it. That is, if there is a way to simulate receiving data in a USB port of my computer so that I can test if my code is working.
Thanks in advance
I am looking into what's the best method for getting external data (custom built hardware) and to intercept and process this data (programming language / tool), the cheapest and easiest and with the least learning curve.
Background:
I am a web dev.
External device will be switches, motion detection, velocity detection
Programming language: Delphy (which I don't know)? or C# (which I know for web dev) or other?
Anyone done anything like this before? Got any advice?
Any and all information is appreciated.
D
The easiest solution might be to use an Arduino.
It's :
cheap (~ 30$)
easy to program
easy to connect to your PC (it use an USB cable which emulate a serial connection)
have a HUGE community with tons of tutorials for doing whatever you want
Here is an example how to control a led using C#
Ok, so I've never done anything with serial connections before. But...
I just got an Arduino that I am trying to use to remotely launch model rockets. I have a 5 volt relay that I can control with the Arduino's digital out.
Now, I want connect my iPhone's Tx to the Arduino's Rx and vice-versa. I would buy the iPhone breakout board from spark fun so I could connect it to the Arduino. (http://www.sparkfun.com/products/10645) I was thinking something along the lines of: when the phone gets a text or a call from a certain number, or maybe even just a bluetooth signal, it would tell the Arduino. But those are just ideas.
How can I actually send a signal from my iPhone? Are there xCode libraries to do this? My phone is jailbroken, so I am open to other non-apple ways for sending signals. But I am a novice programmer.
Thank you.
P.S. I'm new to Stack Overflow, and I would appreciate if you could help me. The first time I posted a question someone told me it wasn't on the right site. So please bear with me.
EDIT #1: Haha, I just read over this and it sounds like a cell phone bomb from a terrorist movie. I swear that's not what I'm doing. Just look at my avatar.
EDIT #2: I also have a Bluetooth dongle for the Arduino. But I honestly have no idea how to interface that with anything, it was $10 from China, so I thought I would buy it to keep my options open. But, regardless, it would be really cool to plug an iPhone into an Arduino.
You could buy a Redpark Serial Cable for iOS to connect the iPhone to your Arduino board over RS-232.
This book also seems to be helpful: iOS Sensor Apps with Arduino
EDIT:
Redpark FAQ: http://redpark.com/c2db9_FAQs.html
There is a SDK available for this serial cable.
You will have trouble writing communication software when trying to connect directly to the dock connector! The External Accessory Framework wont help you here unless your Arduino board has a special decoding chip for dock connector communication.
Have fun!
All I think you need to do is utilize the External Accessory framework. I'm not sure how well it will work for you, the library is meant to communicate with MFi approved accessories. I'd really like to hear how your results went, I am going to be conducting an experiment of my own using a break out board
I am in a similar boat as you, and I have successfully built my own serial cable using the podbreakout, and have implemented a serial class that supports reading / writing. I can confirm that I have read working, as I have tested it with my RFID reader. I am in the process of writing code that will send a command to the Arduino from the iPhone, and then have the Arduino perform a task based on the command.
Here is a document I put together on iDevice serial com,
https://docs.google.com/document/d/1Yi9_hcw8XSyYNCG2OJT9oHlTG-dC-Dnuc58VIULa81Q/edit?usp=sharing
and the serial class can be seen in the project I am working on.
https://github.com/ipatch/KegCop