I got some trouble with my monitor resolution on my new pi2 with an
Philips 284E5QHAD. The monitor can handle full hd but my pi2 seems not to do it.
Thats my basic config (/boot/config.txt)
#middle overclocking
arm_freq=900
core_freq=250
sdram_freq=450
over_voltage=2
# GPU RAM upgrade
gpu_mem=128
# Set sdtv mode to PAL (as used in Europe)
sdtv_mode=2
sdtv_aspect=3
# Force the monitor to HDMI mode so that sound will be sent over HDMI cable
hdmi_drive=2
# Set monitor resolution
#overscan_left=0
#overscan_right=0
#overscan_top=0
#overscan_bottom=0
disable_overscan=1
That's the settings that I tried to use without success:
Test1
hdmi_group=1 | hdmi_mode=16
Test2
hdmi_group=2 | hdmi_mode=32
Test3
hdmi_group=2 | hdmi_mode=82
All with the same result.
Did someone got an idea for me?
I reinstalled the image and it worked with only
disable_overscan=1
Related
Does anyone have a working UBoot config for accessing an NVME drive from UBoot running on a Raspberry Pi CM4?
I've compiled everything and UBoot is detecting my NVME correctly:
pci_bind_bus_devices: bus 1/pci_0:0.0: found device 0, function 0: find ret=-19
pci_find_and_bind_driver: Searching for driver: vendor=2646, device=2263
pci_find_and_bind_driver: Match found: nvme
pci_auto_config_devices: start
pci_auto_config_devices: device nvme#0
PCI Autoconfig: BAR 0, Mem, size=0x4000, address=0xc0000000 bus_lower=0xc0004000
pci_auto_config_devices: done
but it doesnt call nvme_uclass_post_probe() and therefore it doesnt create any block device.
Running the command "nvme scan" from the UBoot command line i'am getting a timeout in nvme_submit_sync_cmd(). -> ETIMEDOUT.
I'am using a Kingston A2000 SDD with the latest firmware "S5Z42109".
Does anyone have an idea?
Thanks.
tl;dr: flashed firmware to 0x00000000 instead of 0x08000000, am I lost?
Hello,
my device is based on a STM32F103CBTx which came with a proprietary firmware and had readout protection on.
I connect to it with a ST-Link v2 SWDIO and SWCLK connected to PA13 and PA14 and this command:
sudo openocd -f /usr/share/openocd/scripts/interface/stlink-v2.cfg -f /usr/share/openocd/scripts/target/stm32f1x.cfg
I don't remember how I removed flash protection, but it worked as the original firmware didn't work anymore. Then I created a simple hello world firmware which pulls up and down three gpios and flashed it. The gpios are pulled up and down in 700ms intervals.
After flashing, I can't connect with openocd anymore. I forgot to specify the offset, the manual says the offset defaults to 0 and as it worked, I suppose instead of the boot loader my shitty hello world is pulling up and down some random pins happily… Is this possible? All other threads I found say the boot loader is write protected.
This is the last contact I had:
> halt
halt
target halted due to debug-request, current mode: Handler HardFault
xPSR: 0x01000003 pc: 0xfffffffe msp: 0xffffffdc
> flash write_image erase fw.hex
flash write_image erase fw.hex
auto erase enabled
target halted due to breakpoint, current mode: Handler HardFault
xPSR: 0x61000003 pc: 0x2000003a msp: 0xffffffdc
wrote 4096 bytes from file fw.hex in 0.285697s (14.001 KiB/s)
> reset
reset
jtag status contains invalid mode value - communication failure
Polling target stm32f1x.cpu failed, trying to reexamine
Examination failed, GDB will be halted. Polling again in 100ms
Any directions highly appreciated.
Edit:
What I get now, also tried another st-link:
% sudo openocd -f /usr/share/openocd/scripts/interface/stlink-v2.cfg -f /usr/share/openocd/scripts/target/stm32f1x.cfg
Open On-Chip Debugger 0.10.0
Licensed under GNU GPL v2
For bug reports, read
http://openocd.org/doc/doxygen/bugs.html
Info : auto-selecting first available session transport "hla_swd". To override use 'transport select '.
Info : The selected transport took over low-level target control. The results might differ compared to plain JTAG/SWD
adapter speed: 1000 kHz
adapter_nsrst_delay: 100
none separate
Info : Unable to match requested speed 1000 kHz, using 950 kHz
Info : Unable to match requested speed 1000 kHz, using 950 kHz
Info : clock speed 950 kHz
Info : STLINK v2 JTAG v17 API v2 SWIM v4 VID 0x0483 PID 0x3748
Info : using stlink api v2
Info : Target voltage: 3.244356
Error: init mode failed (unable to connect to the target)
in procedure 'init'
in procedure 'ocd_bouncer'
flashed firmware to 0x00000000 instead of 0x08000000, am I lost?
No, it doesn't matter at all, they are the same.
After reset, the MCU loads the word at address 0 in SP, and the next one at address 4 in PC. The BOOT0 and BOOT1 pins control which memory gets mapped to 0x00000000. Usually, BOOT0 is tied low, and flash memory at 0x08000000 gets mirrored at 0x00000000.
instead of the boot loader my shitty hello world is pulling up and down some random pins happily… Is this possible? All other threads I found say the boot loader is write protected.
The factory bootloader is indeed write protected, openocd can't overwrite it.
However, your application could have reconfigured the SWD pins, by writing a wrong value in GPIOA->CRH or AFIO->MAPR, thereby preventing openocd from working. It's the most common cause of this problem.
Fortunately, there is a way to recover.
Connect under Reset
If the reset pin of the controller is held low for a while when openocd is started, the application is prevented from starting, and messing up the GPIO configuration.
Openocd can do this automatically, when
It's told to do so, the line reset_config srst_only srst_nogate is present somewhere in the configuration script.
The MCU reset pin is connected to the debugger hardware, pin 15 on an official ST-Link/V2.
Or you can do it manually, by whatever means your board provides. If you are lucky, it has a reset button, if not, you must find a way to somehow ground the MCU reset pin.
Pull the reset pin low
Start openocd
Wait until the Info : Target voltage line appears. Maybe a second longer.
Release the reset pin.
It requires a bit of trial and error, you'll get better with practice.
Then you can flash your improved application, which carefully avoids reconfiguring the SWD pins.
When I try Android Things DP3 with the pi-topCEED, the boot screen isn't displayed properly:
How can I configure Android Things w/ the appropriate display parameter:
Resolution: 1366x768
Refresh rate: 60hz
Mount the sdcard image boot partition
# on my system
mount /dev/sdb1 /mnt/disk
Append the following value to config.txt
# Define new custom HDMI mode <width> <height> <refresh_rate>
hdmi_cvt 1366 768 60
# Select HDMI DMT mode (computer screen)
hdmi_group=2
# Select custom mode defined earlier
hdmi_mode=87
Unmount and eject your sdcard
umount /dev/disk
sync
(Source, Previous Answer)
I am trying to setup a eclipse development environment to work with stm32f303 nucleo 32 board.
http://www.st.com/en/evaluation-tools/nucleo-f303k8.html
So far, the all the tools seems to be correctly installed and working: I have succefully compiled and started openocd debugger for stm32f4 discovery and when I connect stm32f303 nucleo 32 board and start openocd, the led on the board indicates that it is connected. (I have flashed the board.)
The thing is openocd get lost when I do step by step debugging and this seems related to the message openocd gives me when started (look for bold line):
Open On-Chip Debugger 0.9.0 (2015-05-19-12:09)
Licensed under GNU GPL v2
For bug reports, read
http://openocd.org/doc/doxygen/bugs.html
adapter speed: 1000 kHz
adapter_nsrst_delay: 100
Info : The selected transport took over low-level target control. The results might differ compared to plain JTAG/SWD
none separate
srst_only separate srst_nogate srst_open_drain connect_deassert_srst
Info : Unable to match requested speed 1000 kHz, using 950 kHz
Info : Unable to match requested speed 1000 kHz, using 950 kHz
Info : clock speed 950 kHz
**Error: libusb_open() failed with LIBUSB_ERROR_NOT_SUPPORTED**
Info : STLINK v2 JTAG v27 API v2 SWIM v15 VID 0x0483 PID 0x374B
Info : using stlink api v2
Info : Target voltage: 3.239293
Info : stm32f3x.cpu: hardware has 6 breakpoints, 4 watchpoints
Does someone know how to fix usb driver in that case, or it is possible that something else cause the problem?
In case you experience this issue on Linux, you have to configure udev rules to work with the device. Find the 99-openocd.rules included with the source distribution of openOCD under Contributions. Connect your ST-Link USB-device and run 'lsusb' from a terminal, it will list something like this:
Bus 004 Device 009: ID 0483:3748 STMicroelectronics ST-LINK/V2
Notice the value behind ID, you want to check the 99-openocd.rules to see if there is a matching entry supporting the device, in the above case it's this one:
# STLink v2
ATTRS{idVendor}=="0483", ATTRS{idProduct}=="3748", MODE="664", GROUP="plugdev"
Copy this file to your /etc/udev/rules.d configuration directory and reboot your machine. Then try debugging again.
The OpenOCD distribution includes some libusb drivers, and recommends to run the zadig.exe tool to activate them. This will solve your problem.
http://zadig.akeo.ie/
As #silverdr mentioned in the comments, disconnecting the device and reconnecting it worked for me.
how can I use hfp on my ubuntu linux with iphone 5s? I have bluetoooth, all bluez packages and ofono installed.
For ofono I need a modem. From what I understood from bluetooth core, protocoll and profile specification, rfcomm and spp of bluetooth can be used to emulate a modem. How does this work with bluez? Do the bluetoothd and ofonod dbus-services already handle incoming connections to hfp oder do I have to write my own listener?
EDIT:
The program is running. I implemented it according to the test-scripts. But I am experiencing audio issues, as I don't have any sound when performing calls. The sound is not muted.
pa log (translated):
Sep 26 13:57:47 ubu2 pulseaudio[2524]: [alsa-sink-Intel ICH]
alsa-sink.c: ALSA woke us up to write new Data on the Device but there
was nothing to write! Sep 26 13:57:47 ubu2 pulseaudio[2524]:
[alsa-sink-Intel ICH] alsa-sink.c: This is most probably an Error of
the ALSA-Driver 'snd_intel8x0'. Please send this error to the
ALSA-Developers. Sep 26 13:57:47 ubu2 pulseaudio[2524]:
[alsa-sink-Intel ICH] alsa-sink.c: We have been woken up by the
POLLOUT-Set, but a following call of snd_pcm_avail() returned the
value 0 or another value smaller than min_avail.
How can I see if ALSA has encountered some errors? I found no log.
When connecting the a2dp-Profile so that my computer are the speakers of the iPhone I also have no sound.
EDIT 2:
To solve this error, this is recommended:
File: /etc/pulse/default.pa
Add tsched=0 to the following line:
load-module module-detect
from post #21 https://bugs.launchpad.net/ubuntu/+source/linux/+bug/374002
But it does not solve my issue. I try force-loading the also modules too.
Having ofono and bluez should be enough.
However, latest version of bluez/ofono and pulseaudio don't support HSP and HFP profiles.
Pulseaudio release notes say that only A2DP is supported with bluez5.x. If you are using
bluez4.x, ofono and pulseaudio 4.x/5.x you might still get this working without a problem.
http://www.freedesktop.org/wiki/Software/PulseAudio/Notes/5.0/
ofono will treat your iPhone 5s as your modem. Once you get the iPhone paired and connected
through bluetoothctl or any alternative GUI, you could run the following ofono tests to see
if ofono picked it up right. Try running ofonod using ofonod -n -d on a terminal to monitor the debug log and probably run pulseaudio in verbose too (pulseaudio -k && pulseaudio -v)
bash$ cd */ofono-1.x/test
This directory contains sample dbus scripts to test the ofono functionalities.
bash$ ./list-modems
[ /hfp/org/bluez/hci0/dev_94_94_26_88_XX_XX ]
Type = hfp
Interfaces = org.ofono.Siri org.ofono.VoiceCallManager org.ofono.CallVolume org.ofono.Handsfree org.ofono.NetworkRegistration
Features = net
Serial = 94:94:26:88:XX:XX
Online = 1
Powered = 1
Lockdown = 0
Emergency = 0
Name = XXXXXX’s iPhone
[ org.ofono.Siri ]
EyesFreeMode = disabled
Enabled = 1
[ org.ofono.VoiceCallManager ]
EmergencyNumbers = 08 000 999 110 112 911 118 119
[ org.ofono.CallVolume ]
Muted = 0
SpeakerVolume = 50
MicrophoneVolume = 50
[ org.ofono.Handsfree ]
VoiceRecognition = 0
InbandRinging = 1
Features = three-way-calling echo-canceling-and-noise-reduction voice-recognition release-all-held release-specified-active-call private-chat create-multiparty
BatteryChargeLevel = 4
SubscriberNumbers = +XXXXXXXXXXXX
EchoCancelingNoiseReduction = 1
[ org.ofono.NetworkRegistration ]
Status = registered
Name = XXX XXXXXX
Mode = auto-only
Strength = 60
If you see output similar to above, enable the modem and try dialling using the following
command and observe ofono debug log if SCO socket is created or rejected. And, of course,
see if the audio is routed to Ubuntu.
bash$ ./enable-modem
bash$ ./dial-number +XXXXXXXXXXXX
...
Similarly, try calling up your iPhone and observe the ofono, pulseaudio logs.
bash$ ./answer-calls
Looks like folks at pulseaudio are trying to get this working with bluez5.x and ofono but
there doesn't seem to be a patch available publicly yet. The bug is being tracked here:
https://bugs.freedesktop.org/show_bug.cgi?id=73325
HFP for Linux is a Bluetooth Hands-Free Profile server.
It allows your Linux system to act as a speakerphone for your mobile phone. It aims to be a compliant Bluetooth HFP 1.5 Hands Free implementation, supporting all required commands and notifications, as well as streaming audio.
http://nohands.sourceforge.net/