Problem
pi#raspberrypi:/~ $ sudo wvdial
--> WvDial: Internet dialer version 1.61
--> Initializing modem.
--> Sending: ATZ
ATZ
OK
--> Sending: ATQ0 V1 E1 S0=0 &C1 &D2
ATQ0 V1 E1 S0=0 &C1 &D2
OK
--> Modem initialized.
--> Sending: ATDT07********
--> Waiting for carrier.
ATDT07********
NO CARRIER
--> No Carrier! Trying again.
--> Sending: ATDT07********
--> Waiting for carrier.
ATDT07********
NO CARRIER
--> No Carrier! Trying again.
--> Sending: ATDT07********
--> Waiting for carrier.
ATDT07********
NO CARRIER
--> No Carrier! Trying again.
sudo wvdialconf
pi#raspberrypi:/~ $ sudo wvdialconf
Editing `/etc/wvdial.conf'.
Scanning your serial ports for a modem.
ttyUSB0: ATQ0 V1 E1 -- OK
ttyUSB0: ATQ0 V1 E1 Z -- OK
ttyUSB0: ATQ0 V1 E1 S0=0 -- OK
ttyUSB0: ATQ0 V1 E1 S0=0 &C1 -- OK
ttyUSB0: ATQ0 V1 E1 S0=0 &C1 &D2 -- OK
ttyUSB0: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 -- ERROR
ttyUSB0: Modem Identifier: ATI -- Manufacturer: huawei
ttyUSB0: Speed 9600: AT -- OK
ttyUSB0: Max speed is 9600; that should be safe.
ttyUSB0: ATQ0 V1 E1 S0=0 &C1 &D2 -- OK
ttyUSB1: ATQ0 V1 E1 -- failed with 2400 baud, next try: 9600 baud
ttyUSB1: ATQ0 V1 E1 -- failed with 9600 baud, next try: 9600 baud
ttyUSB1: ATQ0 V1 E1 -- and failed too at 115200, giving up.
ttyUSB2: ATQ0 V1 E1 -- OK
ttyUSB2: ATQ0 V1 E1 Z -- OK
ttyUSB2: ATQ0 V1 E1 S0=0 -- OK
ttyUSB2: ATQ0 V1 E1 S0=0 &C1 -- OK
ttyUSB2: ATQ0 V1 E1 S0=0 &C1 &D2 -- OK
ttyUSB2: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 -- ERROR
ttyUSB2: Modem Identifier: ATI -- Manufacturer: huawei
ttyUSB2: Speed 9600: AT -- OK
ttyUSB2: Max speed is 9600; that should be safe.
ttyUSB2: ATQ0 V1 E1 S0=0 &C1 &D2 -- OK
Found a modem on /dev/ttyUSB0.
Modem configuration written to /etc/wvdial.conf.
ttyUSB0: Speed 9600; init "ATQ0 V1 E1 S0=0 &C1 &D2"
ttyUSB2: Speed 9600; init "ATQ0 V1 E1 S0=0 &C1 &D2"
Above details says that i can use ttyUSB0 or ttyUSB2 to send sms
lsusb
Here the dongle is detected as modem
pi#raspberrypi:/~ $ lsusb
Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 001 Device 009: ID 12d1:1001 Huawei Technologies Co., Ltd. E161/E169/E620/E800 HSDPA Modem
Bus 001 Device 003: ID 09da:054f A4Tech Co., Ltd.
Bus 001 Device 002: ID 2109:3431 VIA Labs, Inc. Hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
/etc/wvdial.conf
[Dialer Defaults]
Init1 = ATZ
Init2 = ATQ0 V1 E1 S0=0 &C1 &D2
Modem Type = Analog Modem
ISDN = 0
New PPPD = yes
Phone = 07********
Modem = /dev/ttyUSB0
Username = etisalat
Password = etisalat
Baud = 9600
To send sms through modem, it is required to switch to gsm text mode. wvdial.conf properties have to updated like following:
[Dialer Defaults]
Init1 = AT
#
Init2 = AT+CSCS="GSM"
# Set the GSM modem in SMS Text Mode
Init3 = AT+CMGF=1
# Get info about the current operator.
Init4 = AT+COPS?
# To check whether the GSM/GPRS modem or mobile phone supports SMS text mode,
Init5 = AT+CMGF=?
# Display the currently active modem mode.
Init6 = AT^GETPORTMODE
# : 1,1,1 : SMS text mode send, receive, boradcast supported
Init7 = AT+CSMS=1
# Device model Number
Init8 = AT+GMM
# 31, 3207880 : First number is signal strength, 0...31 where 31 is maximum possible. 2nd number = ?
Init9 = AT+CSQ
# 0,0 : means the modem i snot connected to the network
Init10 = AT+CREG?
# 1 : means CDMA digital service available(0=no service, 2=TDMA, 3=analog)
Init11 = AT+CAD?
# should have said what storage memory is available for SMS
Init12 = AT+CPMS=?
# Type of the modem.
Modem Type = Analog Modem
# The location of the device that wvdial should use as your modem.
Modem = /dev/ttyUSB0
ISDN = 0
Baud = 9600
Dial Attempts = 3
when you save above properties, then wvdial will work fine...
In following file you will see the detailed explanation of all properties
https://github.com/morfikov/files/blob/master/configs/etc/wvdial.conf
https://www.developershome.com/sms/cmgsCommand3.asp
I have a simple udp server/client setup where I send a message from the client and print it on the server. This works well for a regular IP packet but the message is not received when I add an IP options header to the packet, even though I can sniff the packet using scapy.
Here's the packet without IP options
###[ Ethernet ]###
dst = 00:04:00:00:04:01
src = 00:aa:00:02:00:04
type = 0x800
###[ IP ]###
version = 4L
ihl = 5L
tos = 0x0
len = 47
id = 1
flags =
frag = 0L
ttl = 61
proto = udp
chksum = 0x62f4
src = 10.0.2.101
dst = 10.0.4.101
\options \
###[ UDP ]###
sport = 10001
dport = 3478
len = 27
chksum = 0x2bd1
###[ Raw ]###
load = 'message from a game'
And here's the packet with IP options header:
###[ Ethernet ]###
dst = 00:04:00:00:04:01
src = 00:aa:00:02:00:04
type = 0x800
###[ IP ]###
version = 4L
ihl = 8L
tos = 0x0
len = 59
id = 1
flags =
frag = 0L
ttl = 61
proto = udp
chksum = 0x5fe8
src = 10.0.2.101
dst = 10.0.4.101
\options \
|###[ IPOption ]###
| copy_flag = 1L
| optclass = control
| option = 31L
| length = 12
| value = '\x00\x01\x00\x00RTGAME'
###[ UDP ]###
sport = 10001
dport = 3478
len = 27
chksum = 0x2bd1
###[ Raw ]###
load = 'message from a game'
And here's the UDP server:
sock = socket.socket(socket.AF_INET, socket.SOCK_DGRAM)
sock.bind(('', args.port))
while True:
try:
data, addr = sock.recvfrom(1024)
print("received: %s" % data)
except KeyboardInterrupt:
sock.close()
break
I've been stuck on this for a few days and would love if someone could figure it out.
Thanks
have just been playing and the following works as a self-contained/minimal working example for me with Python 3.7.1 under both OSX and Linux
generating a valid set of IP Options:
from scapy.all import IPOption, raw
ipopts = raw(IPOption(
copy_flag=1, optclass='control', option=31,
value='\x00\x01\x00\x00RTGAME'))
(if you don't have Scapy, the above should generate: b'\x9f\x0c\x00\x01\x00\x00RTGAME')
client code:
import socket
from time import sleep
with socket.socket(socket.AF_INET, socket.SOCK_DGRAM) as s:
s.connect(('127.0.0.1', 3478))
s.setsockopt(socket.IPPROTO_IP, socket.IP_OPTIONS, ipopts)
while True:
s.send(b'message from a game')
sleep(1)
server code:
import socket
with socket.socket(socket.AF_INET, socket.SOCK_DGRAM) as s:
s.bind(('', 3478))
s.setsockopt(socket.IPPROTO_IP, socket.IP_RECVOPTS, 1)
while True:
print(*s.recvmsg(4096, 1024))
this should result in the "server" displaying lines like:
b'message from a game\n' [(0, 6, b'\x9f\x0c\x00\x01\x00\x00RTGAME')] 0 ('127.0.0.1', 46047)
furthermore, I can watch packets move over the network by running:
sudo tcpdump -i lo0 -vvv -n 'udp and port 3478'
at the command line, or this in Scapy:
sniff(iface='lo0', filter='udp and port 3478', prn=lambda x: x.show())
for some reason I don't actually receive the ancillary data containing the IP Options under OSX, but the data shows up in the packet sniffers.
The problem was due to an incorrect IPv4 checksum. I failed to mention in the question that I'm running this in a mininet environment with custom switches. The IP options get added in transit by a switch, but the checksum wasn't updated. Once I fixed that, the packet made it to the server.
Thanks for the help and pointers everyone!
Mail from Plesk.
But i recieve this answer
Out: 220 **DOMAIN** ESMTP Postfix (Debian/GNU)
In: EHLO [10.33.205.183]
Out: 250-**DOMAIN**
Out: 250-PIPELINING
Out: 250-SIZE 31457280
Out: 250-ETRN
Out: 250-STARTTLS
Out: 250-AUTH DIGEST-MD5 CRAM-MD5 PLAIN LOGIN
Out: 250-ENHANCEDSTATUSCODES
Out: 250-8BITMIME
Out: 250 DSN
In: STARTTLS
Out: 454 4.7.0 TLS not available due to local problem
In: ???
Out: 502 5.5.2 Error: command not recognized
In: ?????(?'??????
Out: 502 5.5.2 Error: command not recognized
In: ????
Out: 502 5.5.2 Error: command not recognized
Out: 421 4.4.2 **DOMAIN** Error: timeout exceeded
Session aborted, reason: timeout
For other details, see the local mail logfile
Here is my main.cf:
# See /usr/share/postfix/main.cf.dist for a commented, more complete version
# Debian specific: Specifying a file name will cause the first
# line of that file to be used as the name. The Debian default
# is /etc/mailname.
#myorigin = /etc/mailname
smtpd_banner = $myhostname ESMTP $mail_name (Debian/GNU)
biff = no
# appending .domain is the MUA's job.
append_dot_mydomain = no
# Uncomment the next line to generate "delayed mail" warnings
#delay_warning_time = 4h
readme_directory = no
# TLS parameters
smtpd_tls_cert_file = /etc/postfix/tls/httpsd.pem
smtpd_tls_key_file = $smtpd_tls_cert_file
smtpd_use_tls = yes
smtpd_tls_session_cache_database = btree:${data_directory}/smtpd_scache
smtp_tls_session_cache_database = btree:${data_directory}/smtp_scache
# See /usr/share/doc/postfix/TLS_README.gz in the postfix-doc package for
# information on enabling SSL in the smtp client.
myhostname = ***DOMAIN***
alias_maps = hash:/etc/aliases, hash:/var/spool/postfix/plesk/aliases
alias_database = hash:/etc/aliases
myorigin = /etc/mailname
mydestination = localhost.startdedicated.de, localhost, localhost.localdomain
relayhost =
mynetworks = 127.0.0.0/8 [::1]/128 **IP**/32
mailbox_command = procmail -a "$EXTENSION"
mailbox_size_limit = 0
recipient_delimiter = +
inet_interfaces = all
inet_protocols = all
virtual_mailbox_domains = $virtual_mailbox_maps, hash:/var/spool/postfix/plesk/virtual_domains
virtual_alias_maps = $virtual_maps, hash:/var/spool/postfix/plesk/virtual
virtual_mailbox_maps = , hash:/var/spool/postfix/plesk/vmailbox
transport_maps = , hash:/var/spool/postfix/plesk/transport
smtpd_tls_security_level = may
smtp_tls_security_level = may
smtp_use_tls = no
smtpd_timeout = 3600s
smtpd_proxy_timeout = 3600s
disable_vrfy_command = yes
smtpd_sender_restrictions = check_sender_access hash:/var/spool/postfix/plesk/blacklists, permit_sasl_authenticated
smtpd_client_restrictions = permit_mynetworks, permit_sasl_authenticated
smtp_send_xforward_command = yes
smtpd_authorized_xforward_hosts = 127.0.0.0/8 [::1]/128
smtpd_sasl_auth_enable = yes
smtpd_recipient_restrictions = permit_mynetworks, permit_sasl_authenticated, reject_unauth_destination
virtual_mailbox_base = /var/qmail/mailnames
virtual_uid_maps = static:30
virtual_gid_maps = static:31
smtpd_milters = , inet:127.0.0.1:12768
non_smtpd_milters =
sender_dependent_default_transport_maps = hash:/var/spool/postfix/plesk/sdd_transport_maps
virtual_transport = plesk_virtual
plesk_virtual_destination_recipient_limit = 1
mailman_destination_recipient_limit = 1
virtual_mailbox_limit = 0
message_size_limit = 31457280
I should say, that i not be an expert on linux and mailing!
The config file is located: /etc/postfix/main.cf
The cert /etc/postfix/tls/httpsd.pem is the servers default cert.
Thank you!
TL;TR: both bad client and bad server.
The mail server you use is configured wrong in that it believes it can to TLS (as seen in EHLO containing STARTTLS) but then fails to actually use TLS (error when client tries to use TLS). Additionally the client simply ignores the error message to the STARTTLS command and continues with the TLS handshake. This causes error messages from the server which expects proper SMTP commands but instead gets what looks like garbage (the TLS ClientHello).
JavaMail newbie here. I'm trying to figure out what's wrong with a Javamail client that's embeded in a very large system. Sorry I do not have a short, self-contained example, but I'm hoping that someone might be able to give me some tips on how to go about debugging this issue.
It's JavaMail 1.4.3 in Java 7, running on Windows 7. The email server is on a Linux box. The intent of the code is to read all emails in an inbox, delete and expunge them, do some work on the emails, pause for a while, then repeat, looping forever. The problem is that if there are already emails in the inbox when this program starts and the JavaMail client code executes, it does not retrieve them. However, if I send emails to the inbox once the code is running, it retrieves them just fine.
The code gets the inbox with Store.getFolder("INBOX"), opens it with Folder.open(Folder.READ_WRITE) and does a Folder.getMessages(). The getMessages() call always returns no messages when first starting up, but does return the messages sent after the program's been started.
I'm using Pine to verify that the inbox does or does not contains messages, but am not opening the messages in Pine, so they should still be new. And if I use Pine to look at the inbox after running this code, it still contains old messages that were sent before the program was launched, but not any that were sent to it while the program was running (they've been successfully read, deleted and expunged).
The code should also be reading messages that are already in the inbox when it starts. I set mail.debug=true and that output follows. Again, any tips for how to dig into this would be greatly appreciated. Thanks.
// first attempt to read mail when program starts
DEBUG: JavaMail version 1.4.3
DEBUG: successfully loaded resource: /META-INF/javamail.default.providers
DEBUG: Tables of loaded providers
DEBUG: Providers Listed By Class Name: {com.sun.mail.smtp.SMTPSSLTransport=javax.mail.Provider[TRANSPORT,smt
ps,com.sun.mail.smtp.SMTPSSLTransport,Sun Microsystems, Inc], com.sun.mail.smtp.SMTPTransport=javax.mail.Provider[TRANSP
ORT,smtp,com.sun.mail.smtp.SMTPTransport,Sun Microsystems, Inc], com.sun.mail.imap.IMAPSSLStore=javax.mail.Provider[STOR
E,imaps,com.sun.mail.imap.IMAPSSLStore,Sun Microsystems, Inc], com.sun.mail.pop3.POP3SSLStore=javax.mail.Provider[STORE,
pop3s,com.sun.mail.pop3.POP3SSLStore,Sun Microsystems, Inc], com.sun.mail.imap.IMAPStore=javax.mail.Provider[STORE,imap,
com.sun.mail.imap.IMAPStore,Sun Microsystems, Inc], com.sun.mail.pop3.POP3Store=javax.mail.Provider[STORE,pop3,com.sun.m
ail.pop3.POP3Store,Sun Microsystems, Inc]}
DEBUG: Providers Listed By Protocol: {imaps=javax.mail.Provider[STORE,imaps,com.sun.mail.imap.IMAPSSLStore,S
un Microsystems, Inc], imap=javax.mail.Provider[STORE,imap,com.sun.mail.imap.IMAPStore,Sun Microsystems, Inc], smtps=jav
ax.mail.Provider[TRANSPORT,smtps,com.sun.mail.smtp.SMTPSSLTransport,Sun Microsystems, Inc], pop3=javax.mail.Provider[STO
RE,pop3,com.sun.mail.pop3.POP3Store,Sun Microsystems, Inc], pop3s=javax.mail.Provider[STORE,pop3s,com.sun.mail.pop3.POP3
SSLStore,Sun Microsystems, Inc], smtp=javax.mail.Provider[TRANSPORT,smtp,com.sun.mail.smtp.SMTPTransport,Sun Microsystem
s, Inc]}
DEBUG: successfully loaded resource: /META-INF/javamail.default.address.map
DEBUG: getProvider() returning javax.mail.Provider[STORE,imap,com.sun.mail.imap.IMAPStore,Sun Microsystems,
Inc]
DEBUG: mail.imap.fetchsize: 16384
DEBUG: mail.imap.statuscachetimeout: 1000
DEBUG: mail.imap.appendbuffersize: -1
DEBUG: mail.imap.minidletime: 10
DEBUG: trying to connect to host "10.128.200.85", port 143, isSSL false
* OK [CAPABILITY IMAP4REV1 LOGIN-REFERRALS STARTTLS AUTH=LOGIN] pristine.ame.xx.com IMAP4rev1 2001.315rh at Mon, 30 Dec 2013 11:15:26 -0500 (EST)
IMAP DEBUG: AUTH: LOGIN
DEBUG: protocolConnect login, host=10.128.200.85, user=venuswmpublic, password=<non-null>
A0 AUTHENTICATE LOGIN
+ VXNlciBOYW1lAA==
dmVudXN3bXB1YmxpYw==
+ UGFzc3dvcmQA
d2VibTEyMzQ=
A0 OK [CAPABILITY IMAP4REV1 IDLE NAMESPACE MAILBOX-REFERRALS SCAN SORT THREAD=REFERENCES THREAD=ORDEREDSUBJECT MULTIAPPEND] User venuswmpublic authenticated
A1 LIST "" INBOX
* LIST (\NoInferiors) NIL INBOX
A1 OK LIST completed
DEBUG: connection available -- size: 1
A2 SELECT INBOX
* 0 EXISTS
* 0 RECENT
* OK [UIDVALIDITY 1] UID validity status
* OK [UIDNEXT 1] Predicted next UID
* FLAGS (\Answered \Flagged \Deleted \Draft \Seen)
* OK [PERMANENTFLAGS ()] Permanent flags
A2 OK [READ-WRITE] SELECT completed
A3 EXPUNGE
A3 OK EXPUNGE completed
Monitoring incoming email...
* OK [CAPABILITY IMAP4REV1 LOGIN-REFERRALS STARTTLS AUTH=LOGIN] pristine.ame.xx.com IMAP4rev1 2001.315rh at
Mon, 30 Dec 2013 11:15:38 -0500 (EST)
IMAP DEBUG: AUTH: LOGIN
A0 AUTHENTICATE LOGIN
+ VXNlciBOYW1lAA==
dmVudXN3bXB1YmxpYw==
+ UGFzc3dvcmQA
d2VibTEyMzQ=
A0 OK [CAPABILITY IMAP4REV1 IDLE NAMESPACE MAILBOX-REFERRALS SCAN SORT THREAD=REFERENCES THREAD=ORDEREDSUBJECT MULTIAPPEND] User venuswmpublic authenticated
IMAP DEBUG: IMAPProtocol noop
A1 NOOP
A1 OK NOOP completed
IMAP DEBUG: IMAPProtocol noop
A4 NOOP
A4 OK NOOP completed
A5 EXPUNGE
A5 OK EXPUNGE completed
A6 EXPUNGE
A6 OK EXPUNGE completed
DEBUG: pool is full, not adding an Authenticated connection
A7 CLOSE
A7 OK CLOSE completed
A8 LOGOUT
* BYE pristine.ame.xx.com IMAP4rev1 server terminating connection
A8 OK LOGOUT completed
A2 LOGOUT
* BYE pristine.ame.xx.com IMAP4rev1 server terminating connection
A2 OK LOGOUT completed
DEBUG: IMAPStore connection dead
DEBUG: IMAPStore cleanup, force false
DEBUG: IMAPStore cleanup done
// and a bunch of these...
Monitoring incoming email...
IMAP DEBUG: IMAPProtocol noop
A33 NOOP
A33 OK NOOP completed
IMAP DEBUG: IMAPProtocol noop
A77 NOOP
A77 OK NOOP completed
A78 EXPUNGE
A78 OK No messages deleted, so no update needed
Monitoring incoming email...
IMAP DEBUG: IMAPProtocol noop
A34 NOOP
A34 OK NOOP completed
IMAP DEBUG: IMAPProtocol noop
A79 NOOP
A79 OK NOOP completed
A80 EXPUNGE
A80 OK No messages deleted, so no update needed
etc...
------------------------------------
// If I send in an email while the program is running, it picks it up, but still leaves the previous ones unread in the inbox.
Monitoring incoming email...
IMAP DEBUG: IMAPProtocol noop
A4 NOOP
A4 OK NOOP completed
IMAP DEBUG: IMAPProtocol noop
A10 NOOP
* 1 EXISTS
* 1 RECENT
* OK [UIDVALIDITY 1388420519] UID validity status
* OK [UIDNEXT 2] Predicted next UID
* FLAGS (\Answered \Flagged \Deleted \Draft \Seen)
* OK [PERMANENTFLAGS (\* \Answered \Flagged \Deleted \Draft \Seen)] Permanent flags
* OK [READ-WRITE] Mailbox status
* OK [UNSEEN 1] first unseen message in /var/spool/mail/venuswmpublic
A10 OK NOOP completed
A11 EXPUNGE
A11 OK Mailbox checkpointed, but no messages expunged
A12 STORE 1 +FLAGS (\Flagged)
* 1 FETCH (FLAGS (\Recent \Flagged))
A12 OK STORE completed
A13 FETCH 1 (ENVELOPE INTERNALDATE RFC822.SIZE)
* 1 FETCH (ENVELOPE ("Mon, 30 Dec 2013 19:43:42 +0000" "test.testService"
* (("LName, FName" NIL "FName.LName" "Company.com")) (("LName, FName" NIL "FName.LName"
"Company.com")) (("LName, FName" NIL "FName.LName"
"Company.com")) (("venuswmpublic#pristine.ame.xx.com" NIL "venuswmpublic" "pristine.ame.xx.com")) NIL NI
L NIL "<DAF6C79D86A80C49A9F66B898B2821A327FD50E6#hqmbx6.eur.ad.sag>") INTERNALDATE "30-Dec-2013 11:21:51 -0500" RFC822.S
IZE 3774)
A13 OK FETCH completed
A14 FETCH 1 (BODYSTRUCTURE)
* 1 FETCH (BODYSTRUCTURE (("TEXT" "PLAIN" ("CHARSET" "us-ascii") NIL NIL "QUOTED-PRINTABLE" 15 1 NIL NIL NIL
)("TEXT" "HTML" ("CHARSET" "us-ascii") NIL NIL "QUOTED-PRINTABLE" 1899 60 NIL NIL NIL) "ALTERNATIVE" ("BOUNDARY" "_000_D
AF6C79D86A80C49A9F66B898B2821A327FD50E6hqmbx6euradsag_") NIL "EN-US"))
A14 OK FETCH completed
A15 FETCH 1 (BODY[1]<0.15>)
* 1 FETCH (BODY[1]<0> {15}
a=3D111111111
)
* 1 FETCH (FLAGS (\Recent \Seen \Flagged))
A15 OK FETCH completed
A16 FETCH 1 (BODY[1]<0.15>)
* 1 FETCH (BODY[1]<0> {15}
a=3D111111111
)
A16 OK FETCH completed
A17 FETCH 1 (BODY[2]<0.1899>)
* 1 FETCH (BODY[2]<0> {1899}
<html xmlns:v=3D"urn:schemas-microsoft-com:vml" xmlns:o=3D"urn:schemas-micr=
osoft-com:office:office" xmlns:w=3D"urn:schemas-microsoft-com:office:word" =
xmlns:m=3D"http://schemas.microsoft.com/office/2004/12/omml" xmlns=3D"http:=
//www.w3.org/TR/REC-html40">
<head>
<meta http-equiv=3D"Content-Type" content=3D"text/html; charset=3Dus-ascii"=
>
<meta name=3D"Generator" content=3D"Microsoft Word 14 (filtered medium)">
<style><!--
/* Font Definitions */
#font-face
{font-family:Calibri;
panose-1:2 15 5 2 2 2 4 3 2 4;}
#font-face
{font-family:"Trebuchet MS";
panose-1:2 11 6 3 2 2 2 2 2 4;}
/* Style Definitions */
p.MsoNormal, li.MsoNormal, div.MsoNormal
{margin:0in;
margin-bottom:.0001pt;
font-size:11.0pt;
font-family:"Calibri","sans-serif";}
a:link, span.MsoHyperlink
{mso-style-priority:99;
color:blue;
text-decoration:underline;}
a:visited, span.MsoHyperlinkFollowed
{mso-style-priority:99;
color:purple;
text-decoration:underline;}
span.EmailStyle17
{mso-style-type:personal-compose;
font-family:"Trebuchet MS","sans-serif";
color:windowtext;
font-weight:normal;
font-style:normal;
text-decoration:none none;}
.MsoChpDefault
{mso-style-type:export-only;
font-family:"Calibri","sans-serif";}
#page WordSection1
{size:8.5in 11.0in;
margin:1.0in 1.0in 1.0in 1.0in;}
div.WordSection1
{page:WordSection1;}
--></style><!--[if gte mso 9]><xml>
<o:shapedefaults v:ext=3D"edit" spidmax=3D"1026" />
</xml><![endif]--><!--[if gte mso 9]><xml>
<o:shapelayout v:ext=3D"edit">
<o:idmap v:ext=3D"edit" data=3D"1" />
</o:shapelayout></xml><![endif]-->
</head>
<body lang=3D"EN-US" link=3D"blue" vlink=3D"purple">
<div class=3D"WordSection1">
<p class=3D"MsoNormal"><span style=3D"font-size:10.0pt;font-family:"Tr=
ebuchet MS","sans-serif"">a=3D111111111<o:p></o:p></span></p=
>
</div>
</body>
</html>
)
A17 OK FETCH completed
A18 FETCH 1 (BODY[1]<0.15>)
* 1 FETCH (BODY[1]<0> {15}
a=3D111111111
)
A18 OK FETCH completed
DEBUG: JavaMail version 1.4.3
DEBUG: successfully loaded resource: /META-INF/javamail.default.providers
DEBUG: Tables of loaded providers
DEBUG: Providers Listed By Class Name: {com.sun.mail.smtp.SMTPSSLTransport=javax.mail.Provider[TRANSPORT,smt
ps,com.sun.mail.smtp.SMTPSSLTransport,Sun Microsystems, Inc], com.sun.mail.smtp.SMTPTransport=javax.mail.Provider[TRANSP
ORT,smtp,com.sun.mail.smtp.SMTPTransport,Sun Microsystems, Inc], com.sun.mail.imap.IMAPSSLStore=javax.mail.Provider[STOR
E,imaps,com.sun.mail.imap.IMAPSSLStore,Sun Microsystems, Inc], com.sun.mail.pop3.POP3SSLStore=javax.mail.Provider[STORE,
pop3s,com.sun.mail.pop3.POP3SSLStore,Sun Microsystems, Inc], com.sun.mail.imap.IMAPStore=javax.mail.Provider[STORE,imap,
com.sun.mail.imap.IMAPStore,Sun Microsystems, Inc], com.sun.mail.pop3.POP3Store=javax.mail.Provider[STORE,pop3,com.sun.m
ail.pop3.POP3Store,Sun Microsystems, Inc]}
DEBUG: Providers Listed By Protocol: {imaps=javax.mail.Provider[STORE,imaps,com.sun.mail.imap.IMAPSSLStore,S
un Microsystems, Inc], imap=javax.mail.Provider[STORE,imap,com.sun.mail.imap.IMAPStore,Sun Microsystems, Inc], smtps=jav
ax.mail.Provider[TRANSPORT,smtps,com.sun.mail.smtp.SMTPSSLTransport,Sun Microsystems, Inc], pop3=javax.mail.Provider[STO
RE,pop3,com.sun.mail.pop3.POP3Store,Sun Microsystems, Inc], pop3s=javax.mail.Provider[STORE,pop3s,com.sun.mail.pop3.POP3
SSLStore,Sun Microsystems, Inc], smtp=javax.mail.Provider[TRANSPORT,smtp,com.sun.mail.smtp.SMTPTransport,Sun Microsystem
s, Inc]}
DEBUG: successfully loaded resource: /META-INF/javamail.default.address.map
2013-12-30 14:43:53 EST [ISS.0015.0005D] Invoking service test.testService.
2013-12-30 14:43:53 EST [ISP.0090.0001C] ---
2013-12-30 14:43:53 EST [ISP.0090.0001C] --- test.testService EXECUTED !!!
2013-12-30 14:43:53 EST [ISP.0090.0001C] ---
A19 STORE 1 +FLAGS (\Deleted)
* 1 FETCH (FLAGS (\Recent \Seen \Deleted \Flagged))
A19 OK STORE completed
A20 EXPUNGE
* 1 EXPUNGE
* 0 EXISTS
* 0 RECENT
A20 OK Expunged 1 messages
Your server is telling JavaMail that there are no messages in the Inbox ("0 EXISTS") when it first opens it, then a message appears ("1 EXISTS"), which your program processes, deletes, and expunges. That all looks perfectly normal.
If you think there are other messages in the Inbox, the server disagrees. Perhaps you have some messages cached in your Pine client? Perhaps you've set Pine up to work similarly to how most POP3 clients work - download messages from the server, cache them locally, and delete them from the server?