I am setting up openOCD and Eclipse on a new operating system, using a Nucleo F030R8 board that debugs fine on another system. When I run the debugger in Eclipse I get "error in final launch sequence":
Error in final launch sequence
Failed to execute MI command:
-target-select remote localhost:3333
Error message from debugger back end:
localhost:3333: No such file or directory.
Failed to execute MI command:
-target-select remote localhost:3333
Error message from debugger back end:
localhost:3333: No such file or directory.
localhost:3333: No such file or directory.
I can run the debugger in terminal with ./openocd -f board/st_nucleo_f0.cfg and get:
*GNU ARM Eclipse 64-bits Open On-Chip Debugger 0.9.0-00073-gdd34716
(2015-05-19-12:55)
Licensed under GNU GPL v2
For bug reports, read
http://openocd.org/doc/doxygen/bugs.html
Info : The selected transport took over low-level target control. The results
might differ compared to plain JTAG/SWD
adapter speed: 1000 kHz
adapter_nsrst_delay: 100
none separate
srst_only separate srst_nogate srst_open_drain connect_deassert_srst
Info : Unable to match requested speed 1000 kHz, using 950 kHz
Info : Unable to match requested speed 1000 kHz, using 950 kHz
Info : clock speed 950 kHz
Info : STLINK v2 JTAG v25 API v2 SWIM v13 VID 0x0483 PID 0x374B
Info : using stlink api v2
Info : Target voltage: 3.257369
Info : stm32f0x.cpu: hardware has 4 breakpoints, 2 watchpoints''*
and the LED LD1 blinks alternatively green and red. Similarly, I can run External Tools in Eclipse just fine, but this doesn't open the debugger. So it seems like I'm close, but something isn't quite right. Let me know if you need any other details of my system.
Using:
Eclipse Mars.2 (4.5.2)
Mac 10.12.1
OpenOCD 0.10.0-201601101000-dev
GNU Tools gcc-arm-none-eabi-5_4-2016q3
Ok so I figured it out with major credit due to http://www.carminenoviello.com. Running this in terminal:
>telnet localhost 3333
localhost: nodename nor servname provided, or not known
showed this wasn't working correctly. checking /etc/hosts, the file was empty. I changed it to:
##
# Host Database
#
# localhost is used to configure the loopback interface
# when the system is booting. Do not change this entry.
##
127.0.0.1 localhost
255.255.255.255 broadcasthost
::1 localhost
And that was that. Can now enter debug mode.
Related
I'm having a problem: I can't program and debug my STM32G050F6P6 on my PCB.
I talked to many people in order to solve it, but nothing to do.
If you want you can see the discussions by clicking here.
To make a small summary:
with STM32Programmer I can program the MCU without problems (with the .elf file), but if I try to upload the code via STM32Cube IDE I get many problems (same thing for debugging).
I've already tried to change the debug and upload configurations in all possible ways, but NOTHING.
Now I tried to change the resistors that were located between the pins of the microcontroller and the connectors to which SWDIO and SWCLK of the ST-LINK/V2 are connected, and debugging goes with many problems (I remember that before changing the resistors the debugging).
Now that I've changed the resistors, from 1k to 20ohm, I can debug (SWD, Connect Under Rest or Software System Reset, 950khz), but the errors I get are these:
and:
Open On-Chip Debugger 0.11.0+dev-00449-g53fa0f7 (2022-06-09-09:42) [https://github.com/STMicroelectronics/OpenOCD]
Licensed under GNU GPL v2
For bug reports, read
http://openocd.org/doc/doxygen/bugs.html
Info : Listening on port 6666 for tcl connections
Info : Listening on port 4444 for telnet connections
Info : STLINK V2J40S7 (API v2) VID:PID 0483:3748
Info : Target voltage: 3.208388
Info : clock speed 950 kHz
Info : stlink_dap_op_connect(connect)
Info : SWD DPIDR 0x0bc11477
Info : STM32G050F6Px.cpu: Cortex-M0+ r0p1 processor detected
Info : STM32G050F6Px.cpu: target has 4 breakpoints, 2 watchpoints
Info : STM32G050F6Px.cpu: external reset detected
Info : starting gdb server for STM32G050F6Px.cpu on 3333
Info : Listening on port 3333 for gdb connections
Info : accepting 'gdb' connection on tcp/3333
target halted due to debug-request, current mode: Thread
xPSR: 0xf1000000 pc: 0x1fff1654 msp: 0x20000e48
Info : device idcode = 0x10006456 (STM32G05/G06xx - Rev A : 0x1000)
Info : RDP level 0 (0xAA)
Info : flash size = 32kbytes
Info : flash mode : single-bank
Error: Failed to read memory at 0xfffffffe
Error: Failed to read memory at 0xfffffffe
Info : accepting 'gdb' connection on tcp/3333
target halted due to debug-request, current mode: Thread
xPSR: 0xf1000000 pc: 0x1fff1654 msp: 0x20000e48
Info : Padding image section 0 at 0x080018c4 with 4 bytes (bank write end alignment)
target halted due to debug-request, current mode: Thread
xPSR: 0xf1000000 pc: 0x1fff1654 msp: 0x20000e48
Info : STM32G050F6Px.cpu: external reset detected
My question now is if I got the wiring diagram wrong.
Below you will find the image of the wiring diagram of the programming part:
wiring diagram (programming part)
Since I changed those two 1k resistors of SWDIO and SWDCLK (R14 - R15) I get the error from the previous post.
Did I miss something in the wiring diagram?
Addresses 0x1F...... are in the closed-source ROM bootloader, you can't debug that. If you want to debug your application then you need to set the boot mode pins correctly so that it starts, not the ROM. See AN2606 for instructions how to do that.
trying to program and debug STM32F103 (Bluepill) from Atollic TrueStudio 9.3 I got following message:
STMicroelectronics ST-LINK GDB server. Version 5.1.0 Copyright (c)
2018, STMicroelectronics. All rights reserved.
Starting server with the following options:
Persistent Mode : Disabled
Logging Level : 1
Listen Port Number : 61234
Status Refresh Delay : 15s
Verbose Mode : Disabled
SWD Debug : Enabled
Vendor = 0x55
Error in initializing ST-LINK device. Reason: ST-LINK: Could not
verify ST device! Abort connection.
Trying to do the same thing in St-Link utility works without any problems (also erasing and programming):
What could be the problem with this, why does it have problems with verification ?
Tnx for helping in advance!
The problem is that the ID of the STM32F103 on the BluePill and the ID, defined the debugger config files are different. Often the BluePills have counterfeit ICs on them in order to keep the price low, but these do not have the same ID as genuine ICs.
The Instructions/video below are made for STM32CubeIDE however they should also work for TrueSTUDIO.
Video about a workaround: https://youtu.be/bJYp8o7FoYo
Open the Debug Configuration Window
Select ST-LINK(OpenOCD) in the Debug Probe Dropdown
Search stm32f1x.cfg file the C:\ST\STM32CubeIDE_1.2.0\STM32CubeIDE and open it using notepad.
Search for this Line
Now change the ID from 0x1ba01477 to 0x2ba01477 as shown here
Save the file, now debugging should work
this solution also works for clone chips like CH32F103 which is in some cases on BluePill
the other solution is to change a parameter in "stm32f1x.cfg"
open it with a text editor and find this line:
swj_newdap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID
change "$_CPUTAPID" to zero at the end of line it should be like this:
swj_newdap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id 0
after that :Open the Debug Configuration Window like picture above and choose "Select ST-LINK(OpenOCD)" in the Debug Probe Dropdown
then click "Show generator options…” and in Mode setup change"Reset Mode”For“Software system reset”.
both of ways works and i've tested them with CubeIDE and CH32f103c8t6.
remember to change jumper on board
jumpers : up = 0 ; down = 1
I am trying to setup a eclipse development environment to work with stm32f303 nucleo 32 board.
http://www.st.com/en/evaluation-tools/nucleo-f303k8.html
So far, the all the tools seems to be correctly installed and working: I have succefully compiled and started openocd debugger for stm32f4 discovery and when I connect stm32f303 nucleo 32 board and start openocd, the led on the board indicates that it is connected. (I have flashed the board.)
The thing is openocd get lost when I do step by step debugging and this seems related to the message openocd gives me when started (look for bold line):
Open On-Chip Debugger 0.9.0 (2015-05-19-12:09)
Licensed under GNU GPL v2
For bug reports, read
http://openocd.org/doc/doxygen/bugs.html
adapter speed: 1000 kHz
adapter_nsrst_delay: 100
Info : The selected transport took over low-level target control. The results might differ compared to plain JTAG/SWD
none separate
srst_only separate srst_nogate srst_open_drain connect_deassert_srst
Info : Unable to match requested speed 1000 kHz, using 950 kHz
Info : Unable to match requested speed 1000 kHz, using 950 kHz
Info : clock speed 950 kHz
**Error: libusb_open() failed with LIBUSB_ERROR_NOT_SUPPORTED**
Info : STLINK v2 JTAG v27 API v2 SWIM v15 VID 0x0483 PID 0x374B
Info : using stlink api v2
Info : Target voltage: 3.239293
Info : stm32f3x.cpu: hardware has 6 breakpoints, 4 watchpoints
Does someone know how to fix usb driver in that case, or it is possible that something else cause the problem?
In case you experience this issue on Linux, you have to configure udev rules to work with the device. Find the 99-openocd.rules included with the source distribution of openOCD under Contributions. Connect your ST-Link USB-device and run 'lsusb' from a terminal, it will list something like this:
Bus 004 Device 009: ID 0483:3748 STMicroelectronics ST-LINK/V2
Notice the value behind ID, you want to check the 99-openocd.rules to see if there is a matching entry supporting the device, in the above case it's this one:
# STLink v2
ATTRS{idVendor}=="0483", ATTRS{idProduct}=="3748", MODE="664", GROUP="plugdev"
Copy this file to your /etc/udev/rules.d configuration directory and reboot your machine. Then try debugging again.
The OpenOCD distribution includes some libusb drivers, and recommends to run the zadig.exe tool to activate them. This will solve your problem.
http://zadig.akeo.ie/
As #silverdr mentioned in the comments, disconnecting the device and reconnecting it worked for me.
When I start a debugging session under eclipse (luna) for my STM32F429 Discovery board. I get the following error:
OpenOCD failed with code (1).
The information in the console pane is:
Open On-Chip Debugger 0.9.0-dev-00223-g1567cae (2015-01-12-13:43)
Licensed under GNU GPL v2
For bug reports, read
http://openocd.sourceforge.net/doc/doxygen/bugs.html
Info : The selected transport took over low-level target control. The results might differ compared to plain JTAG/SWD
adapter speed: 2000 kHz
adapter_nsrst_delay: 100
srst_only separate srst_nogate srst_open_drain connect_deassert_srst
Started by GNU ARM Eclipse
Info : clock speed 2000 kHz
Error: open failed
in procedure 'init'
in procedure 'ocd_bouncer'
in procedure 'transport'
in procedure 'init'
The "board" file being referenced in the debug setup is: stm32f429discovery.cfg
I did have this working for another ST-Micro board and I could do a full debug session with no problems. Suddenly it just stopped being able to access the board and I get the same errors for it as I get with this board.
I was hoping to be able to use the purely open source s/w that runs on Linux to be able to work with these boards. I'm hoping that someone can get me out of this situation.
Thanks in advance.
Cheers!!
What you use the command and debugger?
try:
openocd -f interface/jlink.cfg -f target/stm32f429discovery.cfg
I'm trying to use Eclipse with GNU ARM plugins to debug my stm32f4-discovery board, however, still no luck. The same board works perfectly in Keil running in the virtual machine, so, it doesn't seem to be hardware problem.
I use Linux Mint 13, I've installed all the prerequisites, I have created templated hello world project, it compiles, and when I try to start debug, it stops at the step "Configuring GDB", and after a couple of seconds it fails with the following:
Error in final launch sequence
Failed to execute MI command:
-target-select remote localhost:3333
Error message from debugger back end:
localhost:3333: Connection timed out.
localhost:3333: Connection timed out.
Then I tried to manually start openocd:
$ openocd -f /usr/local/share/openocd/scripts/board/stm32f4discovery.cfg
Open On-Chip Debugger 0.7.0 (2014-11-08-01:25)
Licensed under GNU GPL v2
For bug reports, read
http://openocd.sourceforge.net/doc/doxygen/bugs.html
srst_only separate srst_nogate srst_open_drain connect_deassert_srst
Info : This adapter doesn't support configurable speed
Info : STLINK v2 JTAG v23 API v2 SWIM v0 VID 0x0483 PID 0x3748
Info : Target voltage: 2.918263
Info : stm32f4x.cpu: hardware has 6 breakpoints, 4 watchpoints
And arm-none-eabi-gdb:
$ arm-none-eabi-gdb ~/projects/test_stm/arm_c_1/Debug/arm_c_1.elf
GNU gdb (GNU Tools for ARM Embedded Processors) 7.6.0.20140731-cvs
Copyright (C) 2013 Free Software Foundation, Inc.
License GPLv3+: GNU GPL version 3 or later <http://gnu.org/licenses/gpl.html>
This is free software: you are free to change and redistribute it.
There is NO WARRANTY, to the extent permitted by law. Type "show copying"
and "show warranty" for details.
This GDB was configured as "--host=i686-pc-linux-gnu --target=arm-none-eabi".
For bug reporting instructions, please see:
<http://www.gnu.org/software/gdb/bugs/>...
Reading symbols from /home/dimon/projects/test_stm/arm_c_1/Debug/arm_c_1.elf...done.
(gdb) target remote localhost:3333
Remote debugging using localhost:3333
0x00000000 in ?? ()
(gdb)
Then, openocd said that connection is accepted:
Info : accepting 'gdb' connection from 3333
Info : stm32f4x errata detected - fixing incorrect MCU_IDCODE
Info : device id = 0x10006413
Info : flash size = 1024kbytes
Warn : acknowledgment received, but no packet pending
undefined debug reason 6 - target needs reset
But, when started by Eclipse, it doesn't work, for some reason.
Well, then I tried to keep openocd started manually and alter my Debug configuration: at the "Debugger" tab, I've unchecked "Start OpenOCD locally". Now, debug session a kind of starts: debug perspective is opened, no meaningful errors are echoed, but debug buttons (resume, suspend, etc) remain inactive. The chip isn't even reprogrammed: previous firmware programmed from inside Keil keeps flashing LEDs.
Here's a screenshot of what Eclipse looks like: http://i.imgur.com/sszA0hr.png
Output of openocd:
$ /usr/local/share/openocd/scripts/board openocd -f ./stm32f4discovery.cfg
Open On-Chip Debugger 0.7.0 (2014-11-08-01:25)
Licensed under GNU GPL v2
For bug reports, read
http://openocd.sourceforge.net/doc/doxygen/bugs.html
srst_only separate srst_nogate srst_open_drain connect_deassert_srst
Info : This adapter doesn't support configurable speed
Info : STLINK v2 JTAG v23 API v2 SWIM v0 VID 0x0483 PID 0x3748
Info : Target voltage: 2.919691
Info : stm32f4x.cpu: hardware has 6 breakpoints, 4 watchpoints
Info : accepting 'gdb' connection from 3333
Info : stm32f4x errata detected - fixing incorrect MCU_IDCODE
Info : device id = 0x10006413
Info : flash size = 1024kbytes
Warn : acknowledgment received, but no packet pending
undefined debug reason 6 - target needs reset
target state: halted
target halted due to debug-request, current mode: Thread
xPSR: 0x01000000 pc: 0x08000154 msp: 0x20030000
semihosting is enabled
target state: halted
target halted due to debug-request, current mode: Thread
xPSR: 0x01000000 pc: 0x08000154 msp: 0x20030000, semihosting
I even tried to re-install all the Eclipse plugins as well as openocd, nothing helped. What could be the trouble?