I have a simulink model. It initially had an algebraic loop but even after adding delay, I am not able to produce any output.
I am representing an equation of the form y(t+1) = 3*y(t).
What should I change to get output of the scope?
The initial condition of the Unit Delay.
Related
I used system identification tool to obtain a state space (order 2) and a process model (2 inputs, 1 output, 2nd order transfer function + delay each) of some data. The models show very nice fit to experimental data in the system identification model output window [Figure 1] but when I use the idmodel block in simulink to simulate the same data it does not look at all like it was on the tool.
I have used exactly the same block diagram with both fitted models. With the state-space fitted model the results are coherent with the system identification tool [Figures 2-3], meanwhile the process model it's totally different [Figures 4-5].
The state-space model only works well with certain experimental conditions, while the process model gives a good fit for all my experiments, that's the reason why I try to use it. The pictures below correspond to only 1 experiment.
I think the problem resides in that I can't set initial conditions to the idmodel block when using a process model instead of a state space model. I can get the initial conditions for the process model using findstates(model, data), but I don't know how to apply them. Any hints on how to set initial conditions for identified transfer function/process models in simulink? Maybe a possible workaround without simulink? I'm open to any solution or ideas.
Thank you.
Figure 1. System identification tool output for both state-space and process model
Figure 2. Simulink output of state-space model
Figure 3. idmodel block with state-space model: initial conditions parameter available
Figure 4. idmodel block with process model: initial conditions parameter NOT available
Figure 5. Simulink output of state-space model
After reaching matlab central and pointing me in the right direction I came up with a solution. Thanks to Rajiv Singh.
I first needed to convert the process model from idproc to idss using idss() instead of ss() -See this article-, then use compare() instead of findstates() to obtain the initial conditions and feed the initial conditions to the idmodel block in simulink. Graphically:
model=idss(T3s_2d);
[y,fit,x0]=compare(run_data_s{8}, model);
%T3s_2d is the identified process model (idproc) from system identification toolbox
%run_data_s is the iddata object with the experimental runs
i want to get values for a simulink model. The aim is to implement the simulink model in a while loop in a matlab script
The simulation has to run 10s. The output of the simulink model is a signal value, which shouldnt exceed the value 1.
The while loop should run, till the right values a,b,c and d are find.
If the simulation is wrong, the value should increment. (a is outer loop and d the inner) All possible combinations should be run.
How it can be implemented, is it possible and how to get with possible errors in the simulink model?
How to get the simulink function data live (If it saved to the workspace, it appears, after the simulation (10s) is done)? I would like to get the results during the run in the workspace.
Have someone experience with it?
Thank you in advance!
I'm new to Matlab/Simulink but have a requirement to interface with a Simulink model from a piece of software.
At the moment I have created a simple Simulink function 'Inc' which has 1 input to an addition block with a constant 1 and an output. I have used To/From Workspace blocks and can run the simulation over a fixed time using a time/value vector input, such as simin = [0,0;5,0;5,1;10,1].
What I would like to do is run my model continuously? Reading Workspace values in real-time rather than a pre-defined time based vector?
I can't see how to set this up? Can Matlab/Simulink do this?
To summarise, I would like simin and simout to be single values i.e. simin = 1, then with the model running continuously(infinitely) at the next fixed step simout would update to simout = 2. simin changes would be made at the Workspace at varying intervals.
The short answer is you can't (easily) do that, that's not how Simulink works. The MATLAB workspace is read/accessed at the beginning of the simulation and passed to the Simulink engine, and even if the values in the workspace change before the simulation is finished, this is not taken into account by the Simulink model running.
There are ways to work around this, but if you are a novice to MATLAB & Simulink, be aware that these are fairly advanced techniques, and I would advise to familiarise yourself with Simulink first.
Have a look at these similar questions for suggestions of how to do what you want:
Stream data form MATLAB to Simulink
Problem of variable updating in workspace
How Do I Change a Block Parameter Based on the Output of Another Block?
Tuning block parameters at every time step in a simulation
Simulink Signal Viewing using Event Listeners and a MATLAB UI
Obviously, you need to change the simulation end time to Inf or some large number.
I have a Simulink model that includes the following subsystem.
The bm_train_adapter block will call a MATLAB function of the same name, passing all the input arguments in a single vector.
The subsystem has been given a sample time of 900 (secs), which is why all the signals are colored in red (for discrete signals).
However, in the debugger I have observed that the bm_train_adapter function gets called twice at each simulation timestep. This yields horribly wrong results since the function includes side-effects.
Why is Simulink calling my interpreted MATLAB function more than once per timestep? How can I prevent this?
I think this is because of your solver setup. In your Configuration Parameters window, check out the Solver Options pane.
I believe the discrete and ode1 solvers will call once per timestep. ode2 will call twice per timestep, ode4 will call 4 times per timestep, etc.
This behavior is very helpful for simulating continuous dynamics, but it can be confusing when interacting with discrete elements.
The reason was that my model had algebraic loops caused by unit delay blocks in subsystems. To solve these loops, the solver had no choice but to evaluate some blocks more than once.
The solution was to move out all unit delays from their subsystems.
I have a model in Simulink describing the behaviour of a system depending on time dependent inputs and model parameters, that can be described as f(a,t).
I have to optimise the model parameters (a) so that the maximum value of the function (f) over a determined time period (T) is below a cetrain value (f0). The problem can be described as to find
MAX(a) SUCH THAT MAX[f(a,t)] < f0 FOR EACH t BELONGING TO T
I have already solved the problem with a MATLAB script, but I want to know if it is possible to do it directly in SIMULINK
Thanks
You need the Simulink Design Optimizer toolbox.