I am a student currently working on a Fiware project. I am trying to collect noise data using my PI with Fiware and I found this tutorial: https://www.fiware.org/tag/raspberry-pi/.
Now I am at step 2 and I want to register my device but it doesn't seem to work. This is the response I get after I run " ./registerDevice 0001 4IN1 " :
root#raspberrypi://home/pi/Desktop/student/fiware-figway/c++# ./registerDevice 0001 4IN1
-> Config file: Debug Level <1>.
-> M2M Platform reply:
**
**
Can anybody help? I'm sure I am missing something I just don't know what.
Related
I took the example of a project Zigbee_OnOff_Client_SED on a module STM32WB5MMGH6TR on custom board.
I have got a supply current of 3 mA instead of 3 μA if the device is connected to hub (H***y) and I have got a supply current of 168 μA instead of 3 μA if the device is connected to Zigbee_OnOff_Server_Coord.
The ST-Link is disconnected.
The symbol STM32WB55xx is redefined to STM32WB5Mxx.
I have tried example PWR_STOP2_RTC but this does not work if I am working on ZigBee stack onboard.
How can I fix sleep mode?
How can I enter the RFD ZigBee stack and RF module in STOP2 mode?
In a wireless project, I'm using en Nucleo STM32WLJC1 in dual core configuration.
I take DualCore Ping Pong ST code example, that I rework to make my own application.
I didn't touch anything of the CMO+ project, I only work on the applicative layer in CM4.
I've some problems about flashing the CM0+ Core.
The first time I flashed the board it works and now I've most of the times the folowing error when I try to flash the CM0+. It sometimes work one time for no reason.
Pop-up Problem Occurred Windows :
Error in final launch sequence:
Failed to start GDB server Failed to start GDB server Error in
initializing ST-LINK device. Reason: (255) Unknown. Please check power
and cabling to target.
Console informations
STMicroelectronics ST-LINK GDB server. Version 6.0.0 Copyright (c)
2021, STMicroelectronics. All rights reserved.
Starting server with the following options:
Persistent Mode : Disabled
Logging Level : 1
Listen Port Number : 61234
Status Refresh Delay : 15s
Verbose Mode : Disabled
SWD Debug : Enabled
Target unknown error 32
Error in initializing ST-LINK device. Reason: Unknown. Please check
power and cabling to target.
It looks like the STlink can't reach the core...
Someone may know what is happening ?
Is there a flashing configuration that has to be done? (to chose which core we want to flash)
trying to program and debug STM32F103 (Bluepill) from Atollic TrueStudio 9.3 I got following message:
STMicroelectronics ST-LINK GDB server. Version 5.1.0 Copyright (c)
2018, STMicroelectronics. All rights reserved.
Starting server with the following options:
Persistent Mode : Disabled
Logging Level : 1
Listen Port Number : 61234
Status Refresh Delay : 15s
Verbose Mode : Disabled
SWD Debug : Enabled
Vendor = 0x55
Error in initializing ST-LINK device. Reason: ST-LINK: Could not
verify ST device! Abort connection.
Trying to do the same thing in St-Link utility works without any problems (also erasing and programming):
What could be the problem with this, why does it have problems with verification ?
Tnx for helping in advance!
The problem is that the ID of the STM32F103 on the BluePill and the ID, defined the debugger config files are different. Often the BluePills have counterfeit ICs on them in order to keep the price low, but these do not have the same ID as genuine ICs.
The Instructions/video below are made for STM32CubeIDE however they should also work for TrueSTUDIO.
Video about a workaround: https://youtu.be/bJYp8o7FoYo
Open the Debug Configuration Window
Select ST-LINK(OpenOCD) in the Debug Probe Dropdown
Search stm32f1x.cfg file the C:\ST\STM32CubeIDE_1.2.0\STM32CubeIDE and open it using notepad.
Search for this Line
Now change the ID from 0x1ba01477 to 0x2ba01477 as shown here
Save the file, now debugging should work
this solution also works for clone chips like CH32F103 which is in some cases on BluePill
the other solution is to change a parameter in "stm32f1x.cfg"
open it with a text editor and find this line:
swj_newdap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID
change "$_CPUTAPID" to zero at the end of line it should be like this:
swj_newdap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id 0
after that :Open the Debug Configuration Window like picture above and choose "Select ST-LINK(OpenOCD)" in the Debug Probe Dropdown
then click "Show generator options…” and in Mode setup change"Reset Mode”For“Software system reset”.
both of ways works and i've tested them with CubeIDE and CH32f103c8t6.
remember to change jumper on board
jumpers : up = 0 ; down = 1
I am trying to setup a eclipse development environment to work with stm32f303 nucleo 32 board.
http://www.st.com/en/evaluation-tools/nucleo-f303k8.html
So far, the all the tools seems to be correctly installed and working: I have succefully compiled and started openocd debugger for stm32f4 discovery and when I connect stm32f303 nucleo 32 board and start openocd, the led on the board indicates that it is connected. (I have flashed the board.)
The thing is openocd get lost when I do step by step debugging and this seems related to the message openocd gives me when started (look for bold line):
Open On-Chip Debugger 0.9.0 (2015-05-19-12:09)
Licensed under GNU GPL v2
For bug reports, read
http://openocd.org/doc/doxygen/bugs.html
adapter speed: 1000 kHz
adapter_nsrst_delay: 100
Info : The selected transport took over low-level target control. The results might differ compared to plain JTAG/SWD
none separate
srst_only separate srst_nogate srst_open_drain connect_deassert_srst
Info : Unable to match requested speed 1000 kHz, using 950 kHz
Info : Unable to match requested speed 1000 kHz, using 950 kHz
Info : clock speed 950 kHz
**Error: libusb_open() failed with LIBUSB_ERROR_NOT_SUPPORTED**
Info : STLINK v2 JTAG v27 API v2 SWIM v15 VID 0x0483 PID 0x374B
Info : using stlink api v2
Info : Target voltage: 3.239293
Info : stm32f3x.cpu: hardware has 6 breakpoints, 4 watchpoints
Does someone know how to fix usb driver in that case, or it is possible that something else cause the problem?
In case you experience this issue on Linux, you have to configure udev rules to work with the device. Find the 99-openocd.rules included with the source distribution of openOCD under Contributions. Connect your ST-Link USB-device and run 'lsusb' from a terminal, it will list something like this:
Bus 004 Device 009: ID 0483:3748 STMicroelectronics ST-LINK/V2
Notice the value behind ID, you want to check the 99-openocd.rules to see if there is a matching entry supporting the device, in the above case it's this one:
# STLink v2
ATTRS{idVendor}=="0483", ATTRS{idProduct}=="3748", MODE="664", GROUP="plugdev"
Copy this file to your /etc/udev/rules.d configuration directory and reboot your machine. Then try debugging again.
The OpenOCD distribution includes some libusb drivers, and recommends to run the zadig.exe tool to activate them. This will solve your problem.
http://zadig.akeo.ie/
As #silverdr mentioned in the comments, disconnecting the device and reconnecting it worked for me.
When I start a debugging session under eclipse (luna) for my STM32F429 Discovery board. I get the following error:
OpenOCD failed with code (1).
The information in the console pane is:
Open On-Chip Debugger 0.9.0-dev-00223-g1567cae (2015-01-12-13:43)
Licensed under GNU GPL v2
For bug reports, read
http://openocd.sourceforge.net/doc/doxygen/bugs.html
Info : The selected transport took over low-level target control. The results might differ compared to plain JTAG/SWD
adapter speed: 2000 kHz
adapter_nsrst_delay: 100
srst_only separate srst_nogate srst_open_drain connect_deassert_srst
Started by GNU ARM Eclipse
Info : clock speed 2000 kHz
Error: open failed
in procedure 'init'
in procedure 'ocd_bouncer'
in procedure 'transport'
in procedure 'init'
The "board" file being referenced in the debug setup is: stm32f429discovery.cfg
I did have this working for another ST-Micro board and I could do a full debug session with no problems. Suddenly it just stopped being able to access the board and I get the same errors for it as I get with this board.
I was hoping to be able to use the purely open source s/w that runs on Linux to be able to work with these boards. I'm hoping that someone can get me out of this situation.
Thanks in advance.
Cheers!!
What you use the command and debugger?
try:
openocd -f interface/jlink.cfg -f target/stm32f429discovery.cfg