I have STM32F4 Discovery. I use IAR embedded Workbench. I am new to this kit. I want to measure distance. my code does not give an error. the distance is always zero. What could be the error? please help me . thanks everyone
#include "stm32f4_discovery.h"
#include "delay.h"
uint32_t Read_Distance(void);
void Init();
uint32_t distance ;
int main()
{
Init(); // initialisation de pin
SysTick_Init(); // pour pouvoire utiliser la fonction delay :)
while (1)
{
distance=Read_Distance();
delay_nms(100);
}
}
void Init()
{
RCC_AHB1PeriphClockCmd(RCC_AHB1Periph_GPIOD, ENABLE);
GPIO_InitTypeDef gpioStructure;
gpioStructure.GPIO_Pin = GPIO_Pin_10;
gpioStructure.GPIO_Mode = GPIO_Mode_OUT;
gpioStructure.GPIO_Speed = GPIO_Speed_100MHz;
GPIO_Init(GPIOD, &gpioStructure);
gpioStructure.GPIO_Pin = GPIO_Pin_11;
gpioStructure.GPIO_Mode = GPIO_Mode_IN;
GPIO_Init(GPIOD, &gpioStructure);
}
//Les Pins pour le Test sont PD10 (Trig) et PD11(echo)
uint32_t Read_Distance(void)
{
__IO uint8_t flag=0;
__IO uint32_t disTime=0;
GPIO_SetBits(GPIOD,GPIO_Pin_10);
delay_nus(10);
GPIO_ResetBits(GPIOD,GPIO_Pin_10);
while(flag == 0)
{
while(GPIO_ReadInputDataBit(GPIOD,GPIO_Pin_11) == SET)
{
disTime++;
flag = 1;
}
}
return disTime;
}
Looks like you're using one of those ultrasonic distance measurement modules
Try this:
while(flag == 0)
{
disTime++;
if(GPIO_ReadInputDataBit(GPIOD,GPIO_Pin_11) == SET)
{
flag = 1;
}
}
You should use one of the hardware timers to get a more accurate time measurement.
Now I've had time to think more about it I remember now that you get a pulse sent back with a width proportional to the distance. I think this is the correct answer:
// Wait for pulse to start
while (GPIO_ReadInputDataBit(GPIOD,GPIO_Pin_11) == RESET)
{
NOP;
}
// Measure pulse width
while(flag == 0)
{
disTime++;
// Has pulse ended
if(GPIO_ReadInputDataBit(GPIOD,GPIO_Pin_11) == RESET)
{
flag = 1;
}
}
You may also want to tackle the case where the pulse is never received because this could will block forever.
If I understand correctly, D10 is wired to D11 and you want to check how long your signal remains high. If this is the case, you should increment a counter in timer interrupt handler when your pin is high and reset that counter variable once you've read it.
Related
I want to connect two UART peripherals using STM32G0 microcontroller via DMA. Not knowing the length of the messages in forward, I'm using function HAL_UARTEx_ReceiveToIdle_DMA() in order to receive them. Here is the part of my code:
main.h
.
.
.
StartDMAReceptionOverUART1();
StartDMAReceptionOverUART4();
/* USER CODE END 2 */
/* Infinite loop */
/* USER CODE BEGIN WHILE */
while (1)
{
/* USER CODE END WHILE */
/* USER CODE BEGIN 3 */
HAL_Delay(10);
}
.
.
.
void StartDMAReceptionOverUART1(void)
{
if (HAL_UARTEx_ReceiveToIdle_DMA(m_modulePort.huart, m_modulePort.rxBuffer, m_modulePort.rxBufferSize) != HAL_OK)
{
Error_Handler();
}
__HAL_DMA_DISABLE_IT(&hdma_usart1_rx, DMA_IT_HT);
__HAL_DMA_DISABLE_IT(&hdma_usart1_rx, DMA_IT_TC);
}
void StartDMAReceptionOverUART4(void)
{
if (HAL_UARTEx_ReceiveToIdle_DMA(m_meterPort.huart, m_meterPort.rxBuffer, m_meterPort.rxBufferSize) != HAL_OK)
{
Error_Handler();
}
__HAL_DMA_DISABLE_IT(&hdma_usart4_rx, DMA_IT_HT);
__HAL_DMA_DISABLE_IT(&hdma_usart4_rx, DMA_IT_TC);
}
.
.
.
These functions are similar: first HAL_UARTEx_ReceiveToIdle_DMA() is checked, then Half Transfer and Transfer Complete interrupts are disabled in order to relieve processor (I need only IDLE interrupt). The problem is inside StartDMAReceptionOverUART1() function, HAL_UARTEx_ReceiveToIdle_DMA() never returns HAL_OK and program jumps on Error_Handler(). On the other hand, StartDMAReceptionOverUART4() works perfectly fine. What could be the problem?
Also, here is the receive callback function, also written inside main.h:
void HAL_UARTEx_RxEventCallback(UART_HandleTypeDef *huart, uint16_t Size)
{
if(huart->Instance == m_meterPort.huart->Instance) // huart == UART4
{
memcpy(m_modulePort.txBuffer, m_meterPort.rxBuffer, Size);
HAL_UART_Transmit_DMA(m_modulePort.huart, m_modulePort.txBuffer, Size);
StartDMAReceptionOverUART4();
}
else if (huart->Instance == m_modulePort.huart->Instance) // huart == UART1
{
memcpy(m_meterPort.txBuffer, m_modulePort.rxBuffer, Size);
HAL_UART_Transmit_DMA(m_meterPort.huart, m_meterPort.txBuffer, Size);
}
else
{
return;
}
}
Callback function, in dependence of the periphery, will copy received data to a buffer and send it to the other periphery (functions memcpy() and HAL_UART_Transmit_DMA()). DMA over UART4 is in Normal mode, therefore StartDMAReceptionOverUART4() is called, inside which is HAL_UARTEx_ReceiveToIdle_DMA(). On the other hand, DMA over UART1 is in Circular mode, so there is no need for calling StartDMAReceptionOverUART4().
I'm trying to make an SPI communication between a F410 MCU and a RPi using SPI.
I post below the code that currently works (without FreeRTOS usage):
main.c
volatile int tx_done = 0;
volatile int rx_done = 0;
void HAL_SPI_TxCpltCallback(SPI_HandleTypeDef *hspi)
{
tx_done = 1;
}
void HAL_SPI_RxCpltCallback(SPI_HandleTypeDef *hspi)
{
rx_done = 1;
}
int main(void)
{
HAL_Init();
SystemClock_Config();
MX_GPIO_Init();
MX_SPI5_Init();
MX_USART2_UART_Init();
const uint8_t BUF_SIZE = 16 * sizeof(uint8_t);
uint8_t buf[16];
// For UART debug
uint8_t dbg_buffer[64];
while (1) {
memset(buf, 0, BUF_SIZE);
HAL_StatusTypeDef ret = HAL_SPI_Receive_IT(&hspi5, (uint8_t*)&buf, BUF_SIZE);
while (rx_done == 0) {};
rx_done = 0;
sprintf((char*) dbg_buffer, "%d %d %d %d %d %d %d %d %d %d %d %d %d %d %d %d]\r\n",
buf[0], buf[1], buf[2], buf[3], buf[4], buf[5], buf[6],
buf[7], buf[8], buf[9], buf[10], buf[11], buf[12],
buf[13], buf[14], buf[15]);
HAL_UART_Transmit(&huart2, dbg_buffer, strlen((char const*) dbg_buffer), 50);
HAL_SPI_Transmit_IT(&hspi5, (uint8_t*) &buf, BUF_SIZE);
while (tx_done == 0) {};
tx_done = 0;
}
}
stm32f4xx_it.c
/**
* #brief This function handles TIM1 trigger and commutation interrupts and TIM11 global interrupt.
*/
void TIM1_TRG_COM_TIM11_IRQHandler(void)
{
HAL_TIM_IRQHandler(&htim11);
}
/**
* #brief This function handles SPI5 global interrupt.
*/
void SPI5_IRQHandler(void)
{
HAL_SPI_IRQHandler(&hspi5);
}
spi.c
/* SPI5 init function */
void MX_SPI5_Init(void)
{
hspi5.Instance = SPI5;
hspi5.Init.Mode = SPI_MODE_SLAVE;
hspi5.Init.Direction = SPI_DIRECTION_2LINES;
hspi5.Init.DataSize = SPI_DATASIZE_8BIT;
hspi5.Init.CLKPolarity = SPI_POLARITY_LOW;
hspi5.Init.CLKPhase = SPI_PHASE_1EDGE;
hspi5.Init.NSS = SPI_NSS_HARD_INPUT;
hspi5.Init.FirstBit = SPI_FIRSTBIT_MSB;
hspi5.Init.TIMode = SPI_TIMODE_DISABLE;
hspi5.Init.CRCCalculation = SPI_CRCCALCULATION_DISABLE;
hspi5.Init.CRCPolynomial = 15;
if (HAL_SPI_Init(&hspi5) != HAL_OK)
{
_Error_Handler(__FILE__, __LINE__);
}
}
void HAL_SPI_MspInit(SPI_HandleTypeDef* spiHandle)
{
[...]
HAL_NVIC_SetPriority(SPI5_IRQn, 5, 0);
HAL_NVIC_EnableIRQ(SPI5_IRQn);
}
This working fine with my test code on the other (raspberry pi) side, sending a SPI frame every second, waiting 100ms and reading the answer from the F410.
Now, when I activate FreeRTOS, I move the while(1) loop content to a task, and creates it with
BaseType_t task1 = xTaskCreate(task_1, "task_1", 512, NULL, tskIDLE_PRIORITY, &xHandle);
and osKernelStart(). I also use the TIM11 as Timebase Source (under SYS tab on CubeMX as advised by the software itself)
Then I have the following behavior: If I place breakpoints inside both Tx/Rx SPI interrupt, I found that a couple (3-4 ?) of them are fired, then never again. If I stop my code I see I'm stucked in the
while (rx_done == 0) {};
loop, confirming that I don't get SPI RX interrupts anymore whereas there is still frame coming on the SPI bus.
To dig a little into that theory, I made another test with this in my task:
while(1) {
memset(buf, 0, 16);
HAL_StatusTypeDef ret = HAL_SPI_Receive_IT(&hspi5, (uint8_t*)&buf, 16);
HAL_GPIO_WritePin(GPIOA, GPIO_PIN_5, GPIO_PIN_SET);
// Wait for RX interrupt, task is suspended to give processing time to (incoming) others tasks
vTaskSuspend(NULL);
HAL_GPIO_WritePin(GPIOA, GPIO_PIN_5, GPIO_PIN_RESET);
}
and in my Rx interrupt, I simply call
xTaskResumeFromISR(task1Handle);
With this code, the first packet sent is read correctly by the STM32F4, and task print it on USART2 and suspend itself again. From then, (checked with a breakpoint inside), the Rx interrupt is never called again, so the task resume inside neither, and my code is frozen...
It really looks like there is a messing between FreeRTOS and STM32 HAL SPI/interrupt handling ?
Any help will be gladly accepted !
Do you call NVIC_PriorityGroupConfig( NVIC_PriorityGroup_4 ); as described in the red text on this page: https://www.freertos.org/RTOS-Cortex-M3-M4.html ?
If you are using an STM32 with the STM32 driver library then ensure all the priority bits are assigned to be preempt priority bits by calling NVIC_PriorityGroupConfig( NVIC_PriorityGroup_4 ); before the RTOS is started.
I am trying to set up a communication between my STM32F4 - Discovery with Open 407V-D development board and a peripheral using UART3 as a RS-485 bus.
I have problem with my communication becouse Rx state of UART remain busy.
Could somebody please explain me what am I doing wrong?
Should I somehow edit HAL_UART_IRQHandler or what setting am I missing?
Here is my code:
#include "main.h"
#include "stm32f4xx_hal.h"
UART_HandleTypeDef huart3;
uint8_t Ocular_1_RxBuffer[4];
uint8_t Ocular_1_TxBuffer[2] = {0x01,0x86};
__IO ITStatus UartReady;
void SystemClock_Config(void);
static void MX_GPIO_Init(void);
static void MX_USART3_UART_Init(void);
int main(void)
{
HAL_Init();
SystemClock_Config();
MX_GPIO_Init();
MX_USART3_UART_Init();
HAL_GPIO_WritePin(GPIOB,GPIO_PIN_9,GPIO_PIN_SET); //set RS 485 into transmit mode
while (1)
{
int Timeout = 1000000;
while(huart3.gState != HAL_UART_STATE_READY) //wait for UART
{
Timeout--;
if(Timeout == 0)
Error_Handler();
}
Timeout = 1000000;
if(HAL_UART_Transmit_IT(&huart3, (uint8_t*)Ocular_1_TxBuffer, 2) != HAL_OK) //Send request
{
Error_Handler();
}
while(huart3.RxState != HAL_UART_STATE_READY) //wait for UART
{
Timeout--;
if(Timeout == 0)
Error_Handler();
}
Timeout = 1000000;
if(HAL_UART_Receive_IT(&huart3, (uint8_t*)Ocular_1_RxBuffer, 4) != HAL_OK) //Response
{
Error_Handler();
}
while(UartReady == RESET) //Wait for response
{
Timeout--;
if(Timeout == 0)
Error_Handler();
}
}
}
I have successfully received response from my peripheral device, but my code generate Error_Handler() after HAL_UART_RxCpltCallback() function.
Could somebody please explain this behavior to me?
My callback functions:
void HAL_UART_TxCpltCallback(UART_HandleTypeDef *UartHandle)
{
/* Set transmission flag: transfer complete */
HAL_GPIO_WritePin(GPIOB,GPIO_PIN_9,GPIO_PIN_RESET);
UartReady = RESET;
}
void HAL_UART_RxCpltCallback(UART_HandleTypeDef *UartHandle)
{
/* Set transmission flag: transfer complete */
HAL_GPIO_WritePin(GPIOB,GPIO_PIN_9,GPIO_PIN_SET);
UartReady = SET;
}
Please mention the number of bytes you are receiving in current scenario.?
Some debugging tips are -
Try increasing the size of your buffer and check if you are receiving any data.
Make sure you are re initialising your buffer after 4 bytes are read. If not the buffer can overflow and may lead to error handler.
Make sure you transmitter always sends 4 bytes.
Confirm if your buad rate matches on both devices. Also settings like parity and all are same in receiver and transmitter.
After every 4 bytes you need to call the HAL_UART_Receive_IT() again to configure and wait for next interrupt.
Add Error callback too, and confirm if execution moves to this callback. If then add prints in driver to find out whats the error cause, whether its like overrun error / Noise error / Parity Error etc.
I have an Arduino with a Seeedstudio sd card shield v4.0 with a prototpye shield above that, and on that is a TMP36 temperature sensor and a red and two green LEDs, the red to show that it is "Ready" to log data, the first green to show that it is currently "logging data" and the last LED to show that the data was "Saved" to the SD card, which it dosent, at the beggining of the file, however, it creates the line "Testing 1, 2, 3..." in a txt file called TEST. in that same file there should be the data, but there is no data, it will write to the card in setup, but not in loop. Can anyone help me?
Code:
#include <toneAC.h>
#include <SPI.h>
#include <SD.h>
int readyLED = 2;
int startLED = 8;
int buzzer = 7;
int tempSensor = A0;
int readyButton = 5;
int sampleNo = 0;
int button_mode = 1;
int saveLED = 4;
File myFile;
void setup() {
// put your setup code here, to run once:
pinMode(readyLED, OUTPUT);
digitalWrite(readyLED, HIGH);
pinMode(saveLED, OUTPUT);
digitalWrite(saveLED, LOW);
pinMode(startLED, OUTPUT);
pinMode(buzzer, OUTPUT);
pinMode(10, OUTPUT);
pinMode(tempSensor, INPUT);
pinMode(readyButton, INPUT);
digitalWrite(readyLED, HIGH);
digitalWrite(startLED, LOW);
Serial.begin(9600);
while (!Serial){}
Serial.println("Initializing SD card...");
if(!SD.begin(4)){
Serial.println("Failed!");
return;
}
Serial.println("Success!");
myFile = SD.open("test.txt", FILE_WRITE);
if (myFile) {
Serial.println("Writing to test.txt...");
myFile.println("testing 1, 2, 3.");
delay(500);
myFile.close();
Serial.println("done.");
} else {
// if the file didn't open, print an error:
Serial.println("error opening test.txt");
}
}
void loop() {
// put your main code here, to run repeatedly:
digitalWrite(readyLED, HIGH);
digitalWrite(startLED, LOW);
delay(700);
digitalWrite(startLED, HIGH);
delay(650);
int reading = analogRead(tempSensor);
float voltage = reading * 5.0;
voltage /= 1024.0;
float temperatureC = (voltage - 0.5) * 100;
float temperatureF = (temperatureC * 9.0 / 5.0) + 32.0;
Serial.print("Sample No. ");
sampleNo = sampleNo + 1;
Serial.print(sampleNo);
Serial.print(" Temperature: ");
Serial.print(temperatureF);
Serial.println(" F");
myFile = SD.open("test.txt", FILE_WRITE);
if(myFile){
Serial.println("Test.txt");
}
while(myFile.available()){
myFile.print("Sample No. ");
myFile.print(sampleNo);
myFile.print(" Temperature: ");
myFile.print(temperatureF);
myFile.println(" F");
}
delay(30);
digitalWrite(saveLED, HIGH);
delay(10);
digitalWrite(saveLED, LOW);
delay(10);
myFile.close();
}
You may want to check to make sure your while loop is actually being run. Since you know you can write to the SD card from void setup() you know your code inside the while loop works, but is the while loop actually being run, or is it evaluating to false and being skipped?
Have you considered the time it takes to write down data as an issue? You may be asking for it write down data before the Arduino code has time to process.
Currently I am trying to get a sketch working where the Arduino will read a series of characters as a command, and do something based on the series of characters sent from an iDevice. I am using an iPhone 3GS that is jailbroken to send characters to the Arduino. The method that sends the serial characters looks like the following,
- (IBAction)blinkFlow_A_LED:(id)sender {
// Method to blink the Flow_A LED on the kegboard-mini Arduino shield (<https://github.com/Kegbot/kegboard>).
NSLog(#"blink Flow_A btn pressed");
// Open serial port / interface
[serial open:B2400];
NSLog(#"%c", [serial isOpened]);
// Send serial data (TX)
char buffer [7];
buffer[0] = '{';
buffer[1] = 'b';
buffer[2] = 'l';
buffer[3] = 'i';
buffer[4] = 'n';
buffer[5] = 'k';
buffer[6] = '}';
[serial write:buffer length:7];
}
I have created a simple sketch that blinks the LED on the shield I am using, but I want the LED to blink conditionally when the button is clicked in the iOS app. The sketch that blinks the LED looks like the following,
/*
Blink
Turns on an LED on for one second, then off for one second, repeatedly.
This sketch is specific to making the kegboard-mini shield.
http://arduino.cc/forum/index.php?topic=157625.new;topicseen#new
This example code is in the public domain.
*/
// Pin D4 - should be connected to the flow_A LED
// Give it a name
int led = 4;
// The setup routine runs once when you press reset:
void setup() {
// Initialize the digital pin as an output.
pinMode(led, OUTPUT);
}
// The loop routine run over and over again forever:
void loop() {
digitalWrite(led, HIGH); // Turn the LED on (HIGH is the voltage level)
delay(1000); // Wait for one second
digitalWrite(led, LOW); // Turn the LED off by making the voltage LOW
delay(1000); // Wait for a second
}
That is a simple sketch!
You may want to begin with looking at the Arduino reference page: Serial
In setup(), you need at least Serial.begin(2400);.
Now, I'll suggest that reading and decoding the string "{blink}" seems like overkill. Let me suggest you send one character (for example 'b'), and detect one character, at least to start. Check out .available() and .read() on the Serial reference page. With these you can determine if a character has arrived at the Arduino and read in a single character.
You can then use these if you want to build a string of characters one at a time and compare it to String("{blink}"). This is a bit more complicated, especially if you take into account exceptions (like lost or damaged characters).
You can easily test your program using the Serial monitor tool -- just be advised that you have to hit "send" to make the characters go out.
I ended putting a simple sketch together like this which allows me to store an array of serial bytes into a String thanks to the SerialEvent example.
The sketch I am currently working with looks like the following,
/*
* kegboard-serial-simple-blink07
* This code is public domain
*
* This sketch sends a receives a multibyte String from the iPhone
* and performs functions on it.
*
* Examples:
* http://arduino.cc/en/Tutorial/SerialEvent
* http://arduino.cc/en/Serial/read
*/
// Global variables should be identified with "_"
// flow_A LED
int led = 4;
// relay_A
const int RELAY_A = A0;
// Variables from the sketch example
String inputString = ""; // A string to hold incoming data
boolean stringComplete = false; // Whether the string is complete
void setup() {
Serial.begin(2400); // Open a serial port. Sets data rate to 2400 bit/s
Serial.println("Power on test");
inputString.reserve(200);
pinMode(RELAY_A, OUTPUT);
}
void open_valve() {
digitalWrite(RELAY_A, HIGH); // Turn RELAY_A on
}
void close_valve() {
digitalWrite(RELAY_A, LOW); // Turn RELAY_A off
}
void flow_A_blink() {
digitalWrite(led, HIGH); // Turn the LED on (HIGH is the voltage level)
delay(1000); // Wait for one second
digitalWrite(led, LOW); // Turn the LED off by making the voltage LOW
delay(1000); // Wait for a second
}
void flow_A_blink_stop() {
digitalWrite(led, LOW);
}
void loop() {
// Print the string when newline arrives:
if (stringComplete) {
Serial.println(inputString);
// Clear the string:
inputString = "";
stringComplete = false;
}
if (inputString == "{blink_Flow_A}") {
flow_A_blink();
}
}
// SerialEvent occurs whenever a new data comes in the
// hardware serial RX. This routine is run between each
// time loop() runs, so using delay inside loop can delay
// response. Multiple bytes of data may be available.
void serialEvent() {
while(Serial.available()) {
// Get the new byte:
char inChar = (char)Serial.read();
// Add it to the inputString:
inputString += inChar;
// If the incoming character is a newline, set a flag
// so the main loop can do something about it:
if (inChar == '\n') {
stringComplete = true;
}
}
}