I've been stuck for a little while now. I am using a PIC18J67j60 with MPLAB IDE (8.92).
My goal is to write my application (application works fine) at the address 0x2A in the PIC18 program memory.
To do so, I added the 18f67j60_g.lkr linker script into my application project (in the "Linker Script" folder). In this 18f67j60_g.lkr script, I added the line : " CODEPAGE NAME=page START=0x2A END=0xFFF".
Then I also added the c018i.c file in the "Source Files" folder of my project and into it, I changed the line "#pragma code _entry_scn=0x000000" to "#pragma code _entry_scn=0x2A".
Everything is compiling and I checked in my project.MAP file and as expected it says : " _entry_scn code 0x00002a program 0x000006" and "start 0x00002a end 0x00013d ".
Then, I use MPLAB IPE only to load the hex.file (obtained from the compilation) (with a pickit3) into my PIC18 (the picKit3 powers the PIC18). BUT in the output window of MPLAP IPE, it says the start writting address is 0x00.. instead of 0x2A. And I dont get why its not writing at 0x2A address..
Thank you for all your help
I'm currently facing a problem with this team of 4.
Using binaries I downloaded on kiska's site. I'm able to compile cobol to C and run it with cobcrun or compile it to an executable. However I can 't get opencobol to find the postgres commands.
Here is the strat of my cobol script :
identification division.
program-id. pgcob.
data division.
working-storage section.
01 pgconn usage pointer.
01 pgres usage pointer.
01 resptr usage pointer.
01 resstr pic x(80) based.
01 result usage binary-long.
01 answer pic x(80).
procedure division.
display "Before connect:" pgconn end-display
call "PQconnectdb" using
by reference "dbname = postgres" & x"00"
by reference "host = 10.37.180.146" & "00"
returning pgconn
end-call
...
the call PQconnectdb fail with module ont found : PQconnectdb
I noticed that if i rename the libpq.dll the error message change to can't find entry point. So at least I'm sure it can get my dll.
After digging into the code of the call method of the libcob library. I found it it was possible to pre load some dll using an environment variable COB_PRE_LOAD but sitll no results.
Here is what look the script to compile the cobol :
call "C:\Program Files (x86)\Microsoft Visual Studio 9.0\VC\bin\amd64\vcvarsamd64.bat"
set COB_CONFIG_DIR=C:\OpenCobol\config
set COB_COPY_DIR=C:\OpenCobol\Copy
set COB_LIBS=%COB_LIBS% c:\OpenCobol\libpq.lib
set COB_LIBRARY_PATH=C:\OpenCobol\bin
set COB_PRE_LOAD=C:\OpenCobol\libpq.dll
#echo on
cobc -info
cobc -free -o pgcob -L:"C:\OpenCobol" -llibpq.lib test_cobol\postgres.cob
call cobcrun pgcob
I don't see anything missing, I'm using the 64-bit binaries from kiska's site and use the 64-bit cl.exe from Visual Studio, Postgres is a 64 bit version too (checked with dependencyChecker).
I even tryed to compile the generated C from Visual Studio, same result, but I may miss something, I'm pretty rotten in C and never really had to manage DLL or use Visual Studio.
What am I missing ?
COB_PRE_LOAD doesn't take any path or extension, see the short documentation for the available runtime configurations. I guess
set COB_LIBRARY_PATH=C:\OpenCobol\bin;C:\OpenCobol
set COB_PRE_LOAD=libpq
Will work. You can omit the C:\OpenCobol\bin if you did not placed any additional executables there.
If it doesn't work (even if it does) I'd try to get the C functions resolved at compile time. Either use
CALL STATIC "PQconnectdb" using ...
or an appropriate CALL-CONVENTION or leave the program as-is and use
cobc -free -o pgcob -L"C:\OpenCobol" -llibpq -K PQconnectdb test_cobol\postgres.cob
From cobc --help:
-K generate CALL to <entry> as static
In general: the binaries from kiska.net are quite outdated. I highly suggest getting newer ones from the official download site or ideally build them on your own from source, see the documentation for building GnuCOBOL with VisualStudio.
I am trying to run ReSharpers command line tool InspectCode.exe. It's running fine doing it's job with the expected output.
However after my earlier attempt to get plugins to work, this time with the new version it is supposed to be supported. There is a switch in the command line interface that allows to specify the extension you want to use.
/extensions (/x) – allows using ReSharper extensions that affect code analysis. To use an extension, specify its ID, which you can find by opening the extension package page in the ReSharper Gallery, and then the Package Statistics page. Multiple values are separated with the semicolon.
But I cannot get it to work properly. I cannot even provoke any reaction to the /x switch at all. No matter how or what I pass, I get no feedback from the executable and the output is identical. I don't even get an error message when passing obvious garbage.
I tried the following commandlines for the exact same result:
inspectcode.exe /o="rcli.xml" /swea /x="ReSharper.StyleCop" "my.sln"
inspectcode.exe /o="rcli.xml" /swea /x=ReSharper.StyleCop "my.sln"
inspectcode.exe /o="rcli.xml" /swea "my.sln"
inspectcode.exe /o="rcli.xml" /swea /x=ABCDEFG "my.sln"
Result
JetBrains Inspect Code 9.1.1
Running in 64-bit mode, .NET runtime 4.0.30319.18444 under Microsoft Windows NT
6.1.7601 Service Pack 1
Enabled solution-wide analysis according to Inspect Code command line Setting.
Analyzing files
[files]
Inspection report was written to rcli.xml
What am I doing wrong? How to get extensions to work?
I already tried the R# forums, but it took them more then 24h to approve my post and so far I'm not sure someone else even read it.
Unfortunately, the support for extensions was dropped in 9.0 due to the refactorings in the "ReSharper platform". I hope that JetBrains will bring it back soon.
See RSRP-436208.
This is a late answer that might help future readers (like myself). Currently inspectcode.exe will automatically look for and use any NuGet packages that are in the same folder as the executable (source).
Example for CleanCode extension:
if you have a R# instance on some machine and install the extension, it will be placed in C:\Users\{user}\AppData\Local\JetBrains\plugins\MO.CleanCode.5.6.15
copy MO.CleanCode.5.6.15.nupkg and paste it next to inspectcode.exe
when running inspectcode with verbosity = VERBOSE, the extension should appear in the Zones list:
$cmd = "..\JetBrains.ReSharper.CommandLineTools.2019.3.4\inspectcode.exe"
$outputFile = "..\Output\$($outputName).xml"
& $cmd -o="$outputFile" $sln --verbosity=VERBOSE
Zones: (52pcs)[CodeInspectionPageImplZone, DaemonEngineZone,
DaemonZone, IAmd64CpuArchitectureHostZone, IAspMvcZone,
IBatchToolEnvironmentZone, IClrImplementationHost Zone,
IClrPsiLanguageZone, ICodeEditingOptionsPageImplZone,
IConsoleEnvironmentZone, ICppProductZone, ICpuArchitectureHostZone,
IDocumentModelZone, IEnvironmentZone, IHostSolutionZone,
IInspectCodeConsoleEnvironmentZone, IInspectCodeEnvironmentZone,
IInspectCodeZone, ILanguageAspZone, ILanguageBuildScriptsZone,
ILanguageCppZone, I LanguageCSharpZone, ILanguageCssZone,
ILanguageHtmlZone, ILanguageIlZone, ILanguageJavaScriptZone,
ILanguageMsBuildZone, ILanguageNAntZone, ILanguageProtobufZone, ILa
nguageRazorZone, ILanguageRegExpZone, ILanguageResxZone,
ILanguageVBZone, ILanguageXamlZone, INetFrameworkHostZone, INuGetZone,
IOperatingSystemHostZone, IProjectMode lZone,
IPsiAssemblyFileLoaderImplZone, IPsiLanguageZone,
IPublicVisibilityZone, IRdFrameworkZone, IRiderModelZone,
ISinceClr2HostZone, ISinceClr4HostZone, ITextContro lsZone,
IToolsOptionsPageImplZone, IWebPsiLanguageZone, IWindowsNtHostZone,
PsiFeaturesImplZone, ReplaceableByIntelliJPlatformZone, SweaZone]
Packages: (23pcs)[JetBrains.ExternalAnnotations,
JetBrains.Platform.Core.Ide, JetBrains.Platform.Core.IisExpress,
JetBrains.Platform.Core.MsBuild, JetBrains.Platform. Core.Shell,
JetBrains.Platform.Core.Text, JetBrains.Platform.Interop.CommandLine,
JetBrains.Platform.Interop.dotMemoryUnit.Framework,
JetBrains.Platform.Interop.dotMe moryUnit.Interop.Console,
JetBrains.Platform.Interop.dotMemoryUnit.Interop.Ide,
JetBrains.Platform.RdProtocol, JetBrains.Psi.Features.Core,
JetBrains.Psi.Features.Cpp .Src.Core, JetBrains.Psi.Features.src,
JetBrains.Psi.Features.Tasks, JetBrains.Psi.Features.UnitTesting,
JetBrains.Psi.Features.Web.Core, JetBrains.ReSharperAutomatio
nTools.src.CleanupCode,
JetBrains.ReSharperAutomationTools.src.CommandLineCore,
JetBrains.ReSharperAutomationTools.src.CommandLineProducts,
JetBrains.ReSharperAutomat ionTools.src.DuplicatesFinder,
JetBrains.ReSharperAutomationTools.src.InspectCode, MO.CleanCode]
Installed EclipseFP, looks without any observable issues. However, when I start Eclipse, I get this:
Whether I click yes or no, the same thing happens on next restart.
Also, in the Hoogle view, I see this:
even though I see the databases seemingly OK in workspace\.metadata\.plugins\net.sf.eclipsefp.haskell.browser\scion-browser-0.2-dbs:
hackage.db 123.71 MB 31.10.2014 09:42:18 Data Base File A
local.db 3.06 MB 31.10.2014 10:20:53 Data Base File A
In the scion-browser console, I have this on startup:
>> {"rebuild":true,"filepath":"C:\\eclipse\\workspace\\.metadata\\.plugins\\net.sf.eclipsefp.haskell.browser\\scion-browser-0.2-dbs\\local.db","command":"load-local-db"}
Local database loaded
"ok"
>> {"module":"","command":"get-modules","db":"_all"}
>> {"rebuild":false,"filepath":"C:\\eclipse\\workspace\\.metadata\\.plugins\\net.sf.eclipsefp.haskell.browser\\scion-browser-0.2-dbs\\hackage.db","command":"load-hackage-db"}
Hackage databas"ok"
e loaded
>> {"module":"Prelude","command":"get-declarations","db":"_all"}
>> {"path":"C:\\eclipse\\workspace\\.metadata\\.plugins\\net.sf.eclipsefp.haskell.ui\\sandbox\\.cabal-sandbox\\bin\\hoogle.exe","command":"extra-hoogle-path"}
"ok"
>> {"command":"hoogle-check"}
C:\eclipse\workspace\.metadata\.plugins\net.sf.eclipsefp.haskell.ui\sandbox\.cabal-sandbox\bin\hoogle.exe
"Error"
Looks like hoogle is not working from the command line either:
C:\>cd C:\eclipse\workspace\.metadata\.plugins\net.sf.eclipsefp.haskell.ui\sandbox\.cabal-sandbox\bin\
C:\eclipse\workspace\.metadata\.plugins\net.sf.eclipsefp.haskell.ui\sandbox\.cabal-sandbox\bin>hoogle fmap
Could not find some databases: default
Searching in:
.
C:\eclipse\workspace\.metadata\.plugins\net.sf.eclipsefp.haskell.ui\sandbox\.cabal-sandbox\x86_64-windows-ghc-7.8.3\hoogle-4.2.36\databases
There are no available databases, generate them with: hoogle data
C:\eclipse\workspace\.metadata\.plugins\net.sf.eclipsefp.haskell.ui\sandbox\.cabal-sandbox\bin>
Any ideas here? I'll add additional information as needed, just not sure what would be useful, let me know and I'll edit.
Looks like for some reason hoogle did not work from the command line either. May be related to this:
C:\eclipse\workspace\.metadata\.plugins\net.sf.eclipsefp.haskell.ui\sandbox\.cabal-sandbox\bin>hoogle data
Downloading downloads/platform.cabal
WARNING: Could not find command line program wget.
You may be able to install it from:
http://gnuwin32.sourceforge.net/packages/wget.htm
WARNING: Could not find command line program curl.
You may be able to install it from:
http://curl.haxx.se/download.html
hoogle: Error when running Shake build system:
* default.hoo
* platform.hoo
* platform.txt
* downloads/platform.cabal.cache
* downloads/platform.cabal
Could not find downloader, neither curl nor wget are on the $PATH.
I have Cygwin installed, so I fixed this by running hoogle data from withing Cygwin terminal, which had wget available in the path and that seems to have solved the issue.
I installed moodle 1.9.12 and now I want to use Algebra notation in content. I enable "TeX Notation" and "Algebra Notation" in administrator panel and also install mimetext and dvips and Imagemagic on the server. fortunately Tex Notation works fine but I got the following error for Algebra:
sh: /var/www/html/moodle/filter/tex/mimetex.linux: not found
The shell command
"/var/www/html/moodle/filter/tex/mimetex.linux" -e "/var/www/moodledata/filter/algebra/de06d6c44d98ba4e42dffca988bf530b.gif" -- '\Large \frac{\sin\left(z\right)}{x^{2}+y^{2}}'
returned status = 127
File size of mimetex executable /var/www/html/moodle/filter/tex/mimetex.linux is 830675
The file permissions are: 100775
The md5 checksum of the file is 56bcc40de905ce92ebd7b083c76e019e
Image not found!
Note: /var/www/html/moodle/filter/tex/mimetex.linux exists on the server and is executable!!!
What is the problem?? Any idea?????
From what you have described, calling the general tex filter debug page works and does not show up the same error.
/filter/tex/texdebug.php works, but /filter/algebra/algebradebug.php does not.
If this is the case, perhaps you could check for an open_basedir, or safe_mode_exec_dir being set to include the current working directory, or otherwise restricting the execution of /var/www/html/moodle/filter/tex/mimetex.linux, while the current working directory is /var/www/html/moodle/filter/algebra.
You could look at this by visiting /admin/phpinfo.php at your site, and look carefully at the effective values of open_basedir, safe_mode and safe_mode_exec_dir.
You could also check the apache error log or add the following lines to the top of the algebra debug php file, and you might see some extra error messages:
$CFG->debug = 6143 ;
$CFG->debugdisplay= 1 ;
Hope that helps