ISPConfig auto-configuring IP address - ispconfig

what's the simpliest way to edit IP address of server in ISPConfig database? I want to deploy virtual servers with ISPConfig but it does not refresh its IP address in ISPConfig. How to achieve it? I can use cloud-init, so maybe some shell script updating MySQL DB which will be initialized by cloud-init?
What is this IP address from ISPConfig DB used for? Is it neccessary to update it?

Running this after first boot does the thing:
ip4=$(/sbin/ip -o -4 addr list eth0 | awk '{print $4}' | cut -d/ -f 1)
mysql -u root --password=$dbpass -D dbispconfig -e "UPDATE server_ip SET ip_address='$ip4' WHERE ip_type='IPv4';"

Related

Schemacrawler container could not connect to host postgresql database [duplicate]

I have a Nginx running inside a docker container. I have a MySql running on the host system. I want to connect to the MySql from within my container. MySql is only binding to the localhost device.
Is there any way to connect to this MySql or any other program on localhost from within this docker container?
This question is different from "How to get the IP address of the docker host from inside a docker container" due to the fact that the IP address of the docker host could be the public IP or the private IP in the network which may or may not be reachable from within the docker container (I mean public IP if hosted at AWS or something). Even if you have the IP address of the docker host it does not mean you can connect to docker host from within the container given that IP address as your Docker network may be overlay, host, bridge, macvlan, none etc which restricts the reachability of that IP address.
Edit:
If you are using Docker-for-mac or Docker-for-Windows 18.03+, connect to your mysql service using the host host.docker.internal (instead of the 127.0.0.1 in your connection string).
If you are using Docker-for-Linux 20.10.0+, you can also use the host host.docker.internal if you started your Docker container with the --add-host host.docker.internal:host-gateway option.
Otherwise, read below
TLDR
Use --network="host" in your docker run command, then 127.0.0.1 in your docker container will point to your docker host.
Note: This mode only works on Docker for Linux, per the documentation.
Note on docker container networking modes
Docker offers different networking modes when running containers. Depending on the mode you choose you would connect to your MySQL database running on the docker host differently.
docker run --network="bridge" (default)
Docker creates a bridge named docker0 by default. Both the docker host and the docker containers have an IP address on that bridge.
on the Docker host, type sudo ip addr show docker0 you will have an output looking like:
[vagrant#docker:~] $ sudo ip addr show docker0
4: docker0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP group default
link/ether 56:84:7a:fe:97:99 brd ff:ff:ff:ff:ff:ff
inet 172.17.42.1/16 scope global docker0
valid_lft forever preferred_lft forever
inet6 fe80::5484:7aff:fefe:9799/64 scope link
valid_lft forever preferred_lft forever
So here my docker host has the IP address 172.17.42.1 on the docker0 network interface.
Now start a new container and get a shell on it: docker run --rm -it ubuntu:trusty bash and within the container type ip addr show eth0 to discover how its main network interface is set up:
root#e77f6a1b3740:/# ip addr show eth0
863: eth0: <BROADCAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP group default qlen 1000
link/ether 66:32:13:f0:f1:e3 brd ff:ff:ff:ff:ff:ff
inet 172.17.1.192/16 scope global eth0
valid_lft forever preferred_lft forever
inet6 fe80::6432:13ff:fef0:f1e3/64 scope link
valid_lft forever preferred_lft forever
Here my container has the IP address 172.17.1.192. Now look at the routing table:
root#e77f6a1b3740:/# route
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
default 172.17.42.1 0.0.0.0 UG 0 0 0 eth0
172.17.0.0 * 255.255.0.0 U 0 0 0 eth0
So the IP Address of the docker host 172.17.42.1 is set as the default route and is accessible from your container.
root#e77f6a1b3740:/# ping 172.17.42.1
PING 172.17.42.1 (172.17.42.1) 56(84) bytes of data.
64 bytes from 172.17.42.1: icmp_seq=1 ttl=64 time=0.070 ms
64 bytes from 172.17.42.1: icmp_seq=2 ttl=64 time=0.201 ms
64 bytes from 172.17.42.1: icmp_seq=3 ttl=64 time=0.116 ms
docker run --network="host"
Alternatively you can run a docker container with network settings set to host. Such a container will share the network stack with the docker host and from the container point of view, localhost (or 127.0.0.1) will refer to the docker host.
Be aware that any port opened in your docker container would be opened on the docker host. And this without requiring the -p or -P docker run option.
IP config on my docker host:
[vagrant#docker:~] $ ip addr show eth0
2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP group default qlen 1000
link/ether 08:00:27:98:dc:aa brd ff:ff:ff:ff:ff:ff
inet 10.0.2.15/24 brd 10.0.2.255 scope global eth0
valid_lft forever preferred_lft forever
inet6 fe80::a00:27ff:fe98:dcaa/64 scope link
valid_lft forever preferred_lft forever
and from a docker container in host mode:
[vagrant#docker:~] $ docker run --rm -it --network=host ubuntu:trusty ip addr show eth0
2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP group default qlen 1000
link/ether 08:00:27:98:dc:aa brd ff:ff:ff:ff:ff:ff
inet 10.0.2.15/24 brd 10.0.2.255 scope global eth0
valid_lft forever preferred_lft forever
inet6 fe80::a00:27ff:fe98:dcaa/64 scope link
valid_lft forever preferred_lft forever
As you can see both the docker host and docker container share the exact same network interface and as such have the same IP address.
Connecting to MySQL from containers
bridge mode
To access MySQL running on the docker host from containers in bridge mode, you need to make sure the MySQL service is listening for connections on the 172.17.42.1 IP address.
To do so, make sure you have either bind-address = 172.17.42.1 or bind-address = 0.0.0.0 in your MySQL config file (my.cnf).
If you need to set an environment variable with the IP address of the gateway, you can run the following code in a container :
export DOCKER_HOST_IP=$(route -n | awk '/UG[ \t]/{print $2}')
then in your application, use the DOCKER_HOST_IP environment variable to open the connection to MySQL.
Note: if you use bind-address = 0.0.0.0 your MySQL server will listen for connections on all network interfaces. That means your MySQL server could be reached from the Internet ; make sure to set up firewall rules accordingly.
Note 2: if you use bind-address = 172.17.42.1 your MySQL server won't listen for connections made to 127.0.0.1. Processes running on the docker host that would want to connect to MySQL would have to use the 172.17.42.1 IP address.
host mode
To access MySQL running on the docker host from containers in host mode, you can keep bind-address = 127.0.0.1 in your MySQL configuration and connect to 127.0.0.1 from your containers:
[vagrant#docker:~] $ docker run --rm -it --network=host mysql mysql -h 127.0.0.1 -uroot -p
Enter password:
Welcome to the MySQL monitor. Commands end with ; or \g.
Your MySQL connection id is 36
Server version: 5.5.41-0ubuntu0.14.04.1 (Ubuntu)
Copyright (c) 2000, 2014, Oracle and/or its affiliates. All rights reserved.
Oracle is a registered trademark of Oracle Corporation and/or its affiliates. Other names may be trademarks of their respective owners.
Type 'help;' or '\h' for help. Type '\c' to clear the current input statement.
mysql>
note: Do use mysql -h 127.0.0.1 and not mysql -h localhost; otherwise the MySQL client would try to connect using a unix socket.
For all platforms
Docker v 20.10 and above (since December 14th 2020)
Use your internal IP address or connect to the special DNS name host.docker.internal which will resolve to the internal IP address used by the host.
On Linux, using the Docker command, add --add-host=host.docker.internal:host-gateway to your Docker command to enable this feature.
To enable this in Docker Compose on Linux, add the following lines to the container definition:
extra_hosts:
- "host.docker.internal:host-gateway"
For older macOS and Windows versions of Docker
Docker v 18.03 and above (since March 21st 2018)
Use your internal IP address or connect to the special DNS name host.docker.internal which will resolve to the internal IP address used by the host.
Linux support pending https://github.com/docker/for-linux/issues/264
For older macOS versions of Docker
Docker for Mac v 17.12 to v 18.02
Same as above but use docker.for.mac.host.internal instead.
Docker for Mac v 17.06 to v 17.11
Same as above but use docker.for.mac.localhost instead.
Docker for Mac 17.05 and below
To access host machine from the docker container you must attach an IP alias to your network interface. You can bind whichever IP you want, just make sure you're not using it to anything else.
sudo ifconfig lo0 alias 123.123.123.123/24
Then make sure that you server is listening to the IP mentioned above or 0.0.0.0. If it's listening on localhost 127.0.0.1 it will not accept the connection.
Then just point your docker container to this IP and you can access the host machine!
To test you can run something like curl -X GET 123.123.123.123:3000 inside the container.
The alias will reset on every reboot so create a start-up script if necessary.
Solution and more documentation here: https://docs.docker.com/docker-for-mac/networking/#use-cases-and-workarounds
Use
host.docker.internal
instead of
localhost
I doing a hack similar to above posts of get the local IP to map to a alias name (DNS) in the container. The major problem is to get dynamically with a simple script that works both in Linux and OSX the host IP address. I did this script that works in both environments (even in Linux distribution with "$LANG" != "en_*" configured):
ifconfig | grep -E "([0-9]{1,3}\.){3}[0-9]{1,3}" | grep -v 127.0.0.1 | awk '{ print $2 }' | cut -f2 -d: | head -n1
So, using Docker Compose, the full configuration will be:
Startup script (docker-run.sh):
export DOCKERHOST=$(ifconfig | grep -E "([0-9]{1,3}\.){3}[0-9]{1,3}" | grep -v 127.0.0.1 | awk '{ print $2 }' | cut -f2 -d: | head -n1)
docker-compose -f docker-compose.yml up
docker-compose.yml:
myapp:
build: .
ports:
- "80:80"
extra_hosts:
- "dockerhost:$DOCKERHOST"
Then change http://localhost to http://dockerhost in your code.
For a more advance guide of how to customize the DOCKERHOST script, take a look at this post with a explanation of how it works.
Solution for Linux (kernel >=3.6).
Ok, your localhost server has a default docker interface docker0 with IP address 172.17.0.1. Your container started with default network settings --net="bridge".
Enable route_localnet for docker0 interface:
$ sysctl -w net.ipv4.conf.docker0.route_localnet=1
Add these rules to iptables:
$ iptables -t nat -I PREROUTING -i docker0 -d 172.17.0.1 -p tcp --dport 3306 -j DNAT --to 127.0.0.1:3306
$ iptables -t filter -I INPUT -i docker0 -d 127.0.0.1 -p tcp --dport 3306 -j ACCEPT
Create MySQL user with access from '%' that means - from anyone, excluding localhost:
CREATE USER 'user'#'%' IDENTIFIED BY 'password';
Change in your script the mysql-server address to 172.17.0.1.
From the kernel documentation:
route_localnet - BOOLEAN: Do not consider loopback addresses as martian source or destination while routing. This enables the use of 127/8 for local routing purposes (default FALSE).
This worked for me on an NGINX/PHP-FPM stack without touching any code or networking where the app's just expecting to be able to connect to localhost
Mount mysqld.sock from the host to inside the container.
Find the location of the mysql.sock file on the host running mysql:
netstat -ln | awk '/mysql(.*)?\.sock/ { print $9 }'
Mount that file to where it's expected in the docker:
docker run -v /hostpath/to/mysqld.sock:/containerpath/to/mysqld.sock
Possible locations of mysqld.sock:
/tmp/mysqld.sock
/var/run/mysqld/mysqld.sock
/var/lib/mysql/mysql.sock
/Applications/MAMP/tmp/mysql/mysql.sock # if running via MAMP
Until host.docker.internal is working for every platform, you can use my container acting as a NAT gateway without any manual setup:
https://github.com/qoomon/docker-host
Simplest solution for Mac OSX
Just use the IP address of your Mac. On the Mac run this to get the IP address and use it from within the container:
ifconfig | grep 'inet 192'| awk '{ print $2}'
As long as the server running locally on your Mac or in another docker container is listening to 0.0.0.0, the docker container will be able to reach out at that address.
If you just want to access another docker container that is listening on 0.0.0.0 you can use 172.17.0.1
Very simple and quick, check your host IP with ifconfig (linux) or ipconfig (windows) and then create a docker-compose.yml:
version: '3' # specify docker-compose version
services:
nginx:
build: ./ # specify the directory of the Dockerfile
ports:
- "8080:80" # specify port mapping
extra_hosts:
- "dockerhost:<yourIP>"
This way, your container will be able to access your host. When accessing your DB, remember to use the name you specified before, in this case dockerhost and the port of your host in which the DB is running.
Several solutions come to mind:
Move your dependencies into containers first
Make your other services externally accessible and connect to them with that external IP
Run your containers without network isolation
Avoid connecting over the network, use a socket that is mounted as a volume instead
The reason this doesn't work out of the box is that containers run with their own network namespace by default. That means localhost (or 127.0.0.1 pointing to the loopback interface) is unique per container. Connecting to this will connect to the container itself, and not services running outside of docker or inside of a different docker container.
Option 1: If your dependency can be moved into a container, I would do this first. It makes your application stack portable as others try to run your container on their own environment. And you can still publish the port on your host where other services that have not been migrated can still reach it. You can even publish the port to the localhost interface on your docker host to avoid it being externally accessible with a syntax like: -p 127.0.0.1:3306:3306 for the published port.
Option 2: There are a variety of ways to detect the host IP address from inside of the container, but each have a limited number of scenarios where they work (e.g. requiring Docker for Mac). The most portable option is to inject your host IP into the container with something like an environment variable or configuration file, e.g.:
docker run --rm -e "HOST_IP=$(ip route get 1 | sed -n 's/^.*src \([0-9.]*\) .*$/\1/p')" ...
This does require that your service is listening on that external interface, which could be a security concern. For other methods to get the host IP address from inside of the container, see this post.
Slightly less portable is to use host.docker.internal. This works in current versions of Docker for Windows and Docker for Mac. And in 20.10, the capability has been added to Docker for Linux when you pass a special host entry with:
docker run --add-host host.docker.internal:host-gateway ...
The host-gateway is a special value added in Docker 20.10 that automatically expands to a host IP. For more details see this PR.
Option 3: Running without network isolation, i.e. running with --net host, means your application is running on the host network namespace. This is less isolation for the container, and it means you cannot access other containers over a shared docker network with DNS (instead, you need to use published ports to access other containerized applications). But for applications that need to access other services on the host that are only listening on 127.0.0.1 on the host, this can be the easiest option.
Option 4: Various services also allow access over a filesystem based socket. This socket can be mounted into the container as a bind mounted volume, allowing you to access the host service without going over the network. For access to the docker engine, you often see examples of mounting /var/run/docker.sock into the container (giving that container root access to the host). With mysql, you can try something like -v /var/run/mysqld/mysqld.sock:/var/run/mysqld/mysql.sock and then connect to localhost which mysql converts to using the socket.
Solution for Windows 10
Docker Community Edition 17.06.0-ce-win18 2017-06-28 (stable)
You can use DNS name of the host docker.for.win.localhost, to resolve to the internal IP. (Warning some sources mentioned windows but it should be win)
Overview
I needed to do something similar, that is connect from my Docker container to my localhost, which was running the Azure Storage Emulator and CosmosDB Emulator.
The Azure Storage Emulator by default listens on 127.0.0.1, while you can change the IP its bound too, I was looking for a solution that would work with default settings.
This also works for connecting from my Docker container to SQL Server and IIS, both running locally on my host with default port settings.
For windows,
I have changed the database url in spring configuration: spring.datasource.url=jdbc:postgresql://host.docker.internal:5432/apidb
Then build the image and run. It worked for me.
None of the answers worked for me when using Docker Toolbox on Windows 10 Home, but 10.0.2.2 did, since it uses VirtualBox which exposes the host to the VM on this address.
This is not an answer to the actual question. This is how I solved a similar problem. The solution comes totally from: Define Docker Container Networking so Containers can Communicate. Thanks to Nic Raboy
Leaving this here for others who might want to do REST calls between one container and another. Answers the question: what to use in place of localhost in a docker environment?
Get how your network looks like docker network ls
Create a new network docker network create -d my-net
Start the first container docker run -d -p 5000:5000 --network="my-net" --name "first_container" <MyImage1:v0.1>
Check out network settings for first container docker inspect first_container. "Networks": should have 'my-net'
Start the second container docker run -d -p 6000:6000 --network="my-net" --name "second_container" <MyImage2:v0.1>
Check out network settings for second container docker inspect second_container. "Networks": should have 'my-net'
ssh into your second container docker exec -it second_container sh or docker exec -it second_container bash.
Inside of the second container, you can ping the first container by ping first_container. Also, your code calls such as http://localhost:5000 can be replaced by http://first_container:5000
If you're running with --net=host, localhost should work fine. If you're using default networking, use the static IP 172.17.0.1.
See this - https://stackoverflow.com/a/48547074/14120621
For those on Windows, assuming you're using the bridge network driver, you'll want to specifically bind MySQL to the IP address of the hyper-v network interface.
This is done via the configuration file under the normally hidden C:\ProgramData\MySQL folder.
Binding to 0.0.0.0 will not work. The address needed is shown in the docker configuration as well, and in my case was 10.0.75.1.
Edit: I ended up prototyping out the concept on GitHub. Check out: https://github.com/sivabudh/system-in-a-box
First, my answer is geared towards 2 groups of people: those who use a Mac, and those who use Linux.
The host network mode doesn't work on a Mac. You have to use an IP alias, see: https://stackoverflow.com/a/43541681/2713729
What is a host network mode? See: https://docs.docker.com/engine/reference/run/#/network-settings
Secondly, for those of you who are using Linux (my direct experience was with Ubuntu 14.04 LTS and I'm upgrading to 16.04 LTS in production soon), yes, you can make the service running inside a Docker container connect to localhost services running on the Docker host (eg. your laptop).
How?
The key is when you run the Docker container, you have to run it with the host mode. The command looks like this:
docker run --network="host" -id <Docker image ID>
When you do an ifconfig (you will need to apt-get install net-tools your container for ifconfig to be callable) inside your container, you will see that the network interfaces are the same as the one on Docker host (eg. your laptop).
It's important to note that I'm a Mac user, but I run Ubuntu under Parallels, so using a Mac is not a disadvantage. ;-)
And this is how you connect NGINX container to the MySQL running on a localhost.
For Linux, where you cannot change the interface the localhost service binds to
There are two problems we need to solve
Getting the IP of the host
Making our localhost service available to Docker
The first problem can be solved using qoomon's docker-host image, as given by other answers.
You will need to add this container to the same bridge network as your other container so that you can access it. Open a terminal inside your container and ensure that you can ping dockerhost.
bash-5.0# ping dockerhost
PING dockerhost (172.20.0.2): 56 data bytes
64 bytes from 172.20.0.2: seq=0 ttl=64 time=0.523 ms
Now, the harder problem, making the service accessible to docker.
We can use telnet to check if we can access a port on the host (you may need to install this).
The problem is that our container will only be able to access services that bind to all interfaces, such as SSH:
bash-5.0# telnet dockerhost 22
SSH-2.0-OpenSSH_7.6p1 Ubuntu-4ubuntu0.3
But services bound only to localhost will be inaccessible:
bash-5.0# telnet dockerhost 1025
telnet: can't connect to remote host (172.20.0.2): Connection refused
The proper solution here would be to bind the service to dockers bridge network. However, this answer assumes that it is not possible for you to change this. So we will instead use iptables.
First, we need to find the name of the bridge network that docker is using with ifconfig. If you are using an unnamed bridge, this will just be docker0. However, if you are using a named network you will have a bridge starting with br- that docker will be using instead. Mine is br-5cd80298d6f4.
Once we have the name of this bridge, we need to allow routing from this bridge to localhost. This is disabled by default for security reasons:
sysctl -w net.ipv4.conf.<bridge_name>.route_localnet=1
Now to set up our iptables rule. Since our container can only access ports on the docker bridge network, we are going to pretend that our service is actually bound to a port on this network.
To do this, we will forward all requests to <docker_bridge>:port to localhost:port
iptables -t nat -A PREROUTING -p tcp -i <docker_bridge_name> --dport <service_port> -j DNAT --to-destination 127.0.0.1:<service_port>
For example, for my service on port 1025
iptables -t nat -A PREROUTING -p tcp -i br-5cd80298d6f4 --dport 1025 -j DNAT --to-destination 127.0.0.1:1025
You should now be able to access your service from the container:
bash-5.0# telnet dockerhost 1025
220 127.0.0.1 ESMTP Service Ready
First see this answer for the options that you have to fix this problem. But if you use docker-compose you can add network_mode: host to your service and then use 127.0.0.1 to connect to the local host. This is just one of the options described in the answer above. Below you can find how I modified docker-compose.yml from https://github.com/geerlingguy/php-apache-container.git:
---
version: "3"
services:
php-apache:
+ network_mode: host
image: geerlingguy/php-apache:latest
container_name: php-apache
...
+ indicates the line I added.
[Additional info] This has also worked in version 2.2. and "host" or just 'host' are both worked in docker-compose.
---
version: "2.2"
services:
php-apache:
+ network_mode: "host"
or
+ network_mode: host
...
I disagree with the answer from Thomasleveil.
Making mysql bind to 172.17.42.1 will prevent other programs using the database on the host to reach it. This will only work if all your database users are dockerized.
Making mysql bind to 0.0.0.0 will open the db to outside world, which is not only a very bad thing to do, but also contrary to what the original question author wants to do. He explicitly says "The MySql is running on localhost and not exposing a port to the outside world, so its bound on localhost"
To answer the comment from ivant
"Why not bind mysql to docker0 as well?"
This is not possible. The mysql/mariadb documentation explicitly says it is not possible to bind to several interfaces. You can only bind to 0, 1, or all interfaces.
As a conclusion, I have NOT found any way to reach the (localhost only) database on the host from a docker container. That definitely seems like a very very common pattern, but I don't know how to do it.
Try this:
version: '3.5'
services:
yourservice-here:
container_name: container_name
ports:
- "4000:4000"
extra_hosts: # <---- here
- localhost:192.168.1.202
- or-vitualhost.local:192.168.1.202
To get 192.168.1.202, uses ifconfig
This worked for me. Hope this help!
In 7 years the question was asked, it is either docker has changed, or no one tried this way. So I will include my own answer.
I have found all answers use complex methods. Today, I have needed this, and found 2 very simple ways:
use ipconfig or ifconfig on your host and make note of all IP addresses. At least two of them can be used by the container.
I have a fixed local network address on WiFi LAN Adapter: 192.168.1.101. This could be 10.0.1.101. the result will change depending on your router
I use WSL on windows, and it has its own vEthernet address: 172.19.192.1
use host.docker.internal. Most answers have this or another form of it depending on OS. The name suggests it is now globally used by docker.
A third option is to use WAN address of the machine, or in other words IP given by the service provider. However, this may not work if IP is not static, and requires routing and firewall settings.
You need to know the gateway! My solution with local server was to expose it under 0.0.0.0:8000, then run docker with subnet and run container like:
docker network create --subnet=172.35.0.0/16 --gateway 172.35.0.1 SUBNET35
docker run -d -p 4444:4444 --net SUBNET35 <container-you-want-run-place-here>
So, now you can access your loopback through http://172.35.0.1:8000
Connect to the gateway address.
❯ docker network inspect bridge | grep Gateway
"Gateway": "172.17.0.1"
Make sure the process on the host is listening on this interface or on all interfaces and is started after docker. If using systemd, you can add the below to make sure it is started after docker.
[Unit]
After=docker.service
Example
❯ python -m http.server &> /dev/null &
[1] 149976
❯ docker run --rm python python -c "from urllib.request import urlopen;print(b'Directory listing for' in urlopen('http://172.17.0.1:8000').read())"
True
Here is my solution : it works for my case
set local mysql server to public access by comment
#bind-address = 127.0.0.1
in /etc/mysql/mysql.conf.d
restart mysql server
sudo /etc/init.d/mysql restart
run the following command to open user root access any host
mysql -uroot -proot
GRANT ALL PRIVILEGES ON *.* TO 'root'#'%' IDENTIFIED BY 'root' WITH
GRANT OPTION;
FLUSH PRIVILEGES;
create sh script : run_docker.sh
#!bin/bash
HOSTIP=`ip -4 addr show scope global dev eth0 | grep inet | awk '{print \$2}' | cut -d / -f 1`
docker run -it -d --name web-app \
--add-host=local:${HOSTIP} \
-p 8080:8080 \
-e DATABASE_HOST=${HOSTIP} \
-e DATABASE_PORT=3306 \
-e DATABASE_NAME=demo \
-e DATABASE_USER=root \
-e DATABASE_PASSWORD=root \
sopheamak/springboot_docker_mysql
run with docker-composer
version: '2.1'
services:
tomcatwar:
extra_hosts:
- "local:10.1.2.232"
image: sopheamak/springboot_docker_mysql
ports:
- 8080:8080
environment:
- DATABASE_HOST=local
- DATABASE_USER=root
- DATABASE_PASSWORD=root
- DATABASE_NAME=demo
- DATABASE_PORT=3306
You can get the host ip using alpine image
docker run --rm alpine ip route | awk 'NR==1 {print $3}'
This would be more consistent as you're always using alpine to run the command.
Similar to Mariano's answer you can use same command to set an environment variable
DOCKER_HOST=$(docker run --rm alpine ip route | awk 'NR==1 {print $3}') docker-compose up
you can use net alias for your machine
OSX
sudo ifconfig lo0 alias 123.123.123.123/24 up
LINUX
sudo ifconfig lo:0 123.123.123.123 up
then from the container you can see the machine by 123.123.123.123
The CGroups and Namespaces are playing major role in the Container Ecosystem.
Namespace provide a layer of isolation. Each container runs in a separate namespace and its access is limited to that namespace. The Cgroups controls the resource utilization of each container, whereas Namespace controls what a process can see and access the respective resource.
Here is the basic understanding of the solution approach you could follow,
Use Network Namespace
When a container spawns out of image, a network interface is defined and create. This gives the container unique IP address and interface.
$ docker run -it alpine ifconfig
By changing the namespace to host, cotainers networks does not remain isolated to its interface, the process will have access to host machines network interface.
$ docker run -it --net=host alpine ifconfig
If the process listens on ports, they'll be listened on the host interface and mapped to the container.
Use PID Namespace
By changing the Pid namespace allows a container to interact with other process beyond its normal scope.
This container will run in its own namespace.
$ docker run -it alpine ps aux
By changing the namespace to the host, the container can also see all the other processes running on the system.
$ docker run -it --pid=host alpine ps aux
Sharing Namespace
This is a bad practice to do this in production because you are breaking out of the container security model which might open up for vulnerabilities, and easy access to eavesdropper. This is only for debugging tools and understating the loopholes in container security.
The first container is nginx server. This will create a new network and process namespace. This container will bind itself to port 80 of newly created network interface.
$ docker run -d --name http nginx:alpine
Another container can now reuse this namespace,
$ docker run --net=container:http mohan08p/curl curl -s localhost
Also, this container can see the interface with the processes in a shared container.
$ docker run --pid=container:http alpine ps aux
This will allow you give more privileges to containers without changing or restarting the application. In the similar way you can connect to mysql on host, run and debug your application. But, its not recommend to go by this way. Hope it helps.
Until fix is not merged into master branch, to get host IP just run from inside of the container:
ip -4 route list match 0/0 | cut -d' ' -f3
(as suggested by #Mahoney here).
I solved it by creating a user in MySQL for the container's ip:
$ sudo mysql<br>
mysql> create user 'username'#'172.17.0.2' identified by 'password';<br>
Query OK, 0 rows affected (0.00 sec)
mysql> grant all privileges on database_name.* to 'username'#'172.17.0.2' with grant option;<br>
Query OK, 0 rows affected (0.00 sec)
$ sudo vim /etc/mysql/mysql.conf.d/mysqld.cnf
<br>bind-address = 172.17.0.1
$ sudo systemctl restart mysql.service
Then on container: jdbc:mysql://<b>172.17.0.1</b>:3306/database_name

Unable to connect to a local postgreSql database on flask project using docker (WSL2) [duplicate]

I have a Nginx running inside a docker container. I have a MySql running on the host system. I want to connect to the MySql from within my container. MySql is only binding to the localhost device.
Is there any way to connect to this MySql or any other program on localhost from within this docker container?
This question is different from "How to get the IP address of the docker host from inside a docker container" due to the fact that the IP address of the docker host could be the public IP or the private IP in the network which may or may not be reachable from within the docker container (I mean public IP if hosted at AWS or something). Even if you have the IP address of the docker host it does not mean you can connect to docker host from within the container given that IP address as your Docker network may be overlay, host, bridge, macvlan, none etc which restricts the reachability of that IP address.
Edit:
If you are using Docker-for-mac or Docker-for-Windows 18.03+, connect to your mysql service using the host host.docker.internal (instead of the 127.0.0.1 in your connection string).
If you are using Docker-for-Linux 20.10.0+, you can also use the host host.docker.internal if you started your Docker container with the --add-host host.docker.internal:host-gateway option.
Otherwise, read below
TLDR
Use --network="host" in your docker run command, then 127.0.0.1 in your docker container will point to your docker host.
Note: This mode only works on Docker for Linux, per the documentation.
Note on docker container networking modes
Docker offers different networking modes when running containers. Depending on the mode you choose you would connect to your MySQL database running on the docker host differently.
docker run --network="bridge" (default)
Docker creates a bridge named docker0 by default. Both the docker host and the docker containers have an IP address on that bridge.
on the Docker host, type sudo ip addr show docker0 you will have an output looking like:
[vagrant#docker:~] $ sudo ip addr show docker0
4: docker0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP group default
link/ether 56:84:7a:fe:97:99 brd ff:ff:ff:ff:ff:ff
inet 172.17.42.1/16 scope global docker0
valid_lft forever preferred_lft forever
inet6 fe80::5484:7aff:fefe:9799/64 scope link
valid_lft forever preferred_lft forever
So here my docker host has the IP address 172.17.42.1 on the docker0 network interface.
Now start a new container and get a shell on it: docker run --rm -it ubuntu:trusty bash and within the container type ip addr show eth0 to discover how its main network interface is set up:
root#e77f6a1b3740:/# ip addr show eth0
863: eth0: <BROADCAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP group default qlen 1000
link/ether 66:32:13:f0:f1:e3 brd ff:ff:ff:ff:ff:ff
inet 172.17.1.192/16 scope global eth0
valid_lft forever preferred_lft forever
inet6 fe80::6432:13ff:fef0:f1e3/64 scope link
valid_lft forever preferred_lft forever
Here my container has the IP address 172.17.1.192. Now look at the routing table:
root#e77f6a1b3740:/# route
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
default 172.17.42.1 0.0.0.0 UG 0 0 0 eth0
172.17.0.0 * 255.255.0.0 U 0 0 0 eth0
So the IP Address of the docker host 172.17.42.1 is set as the default route and is accessible from your container.
root#e77f6a1b3740:/# ping 172.17.42.1
PING 172.17.42.1 (172.17.42.1) 56(84) bytes of data.
64 bytes from 172.17.42.1: icmp_seq=1 ttl=64 time=0.070 ms
64 bytes from 172.17.42.1: icmp_seq=2 ttl=64 time=0.201 ms
64 bytes from 172.17.42.1: icmp_seq=3 ttl=64 time=0.116 ms
docker run --network="host"
Alternatively you can run a docker container with network settings set to host. Such a container will share the network stack with the docker host and from the container point of view, localhost (or 127.0.0.1) will refer to the docker host.
Be aware that any port opened in your docker container would be opened on the docker host. And this without requiring the -p or -P docker run option.
IP config on my docker host:
[vagrant#docker:~] $ ip addr show eth0
2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP group default qlen 1000
link/ether 08:00:27:98:dc:aa brd ff:ff:ff:ff:ff:ff
inet 10.0.2.15/24 brd 10.0.2.255 scope global eth0
valid_lft forever preferred_lft forever
inet6 fe80::a00:27ff:fe98:dcaa/64 scope link
valid_lft forever preferred_lft forever
and from a docker container in host mode:
[vagrant#docker:~] $ docker run --rm -it --network=host ubuntu:trusty ip addr show eth0
2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP group default qlen 1000
link/ether 08:00:27:98:dc:aa brd ff:ff:ff:ff:ff:ff
inet 10.0.2.15/24 brd 10.0.2.255 scope global eth0
valid_lft forever preferred_lft forever
inet6 fe80::a00:27ff:fe98:dcaa/64 scope link
valid_lft forever preferred_lft forever
As you can see both the docker host and docker container share the exact same network interface and as such have the same IP address.
Connecting to MySQL from containers
bridge mode
To access MySQL running on the docker host from containers in bridge mode, you need to make sure the MySQL service is listening for connections on the 172.17.42.1 IP address.
To do so, make sure you have either bind-address = 172.17.42.1 or bind-address = 0.0.0.0 in your MySQL config file (my.cnf).
If you need to set an environment variable with the IP address of the gateway, you can run the following code in a container :
export DOCKER_HOST_IP=$(route -n | awk '/UG[ \t]/{print $2}')
then in your application, use the DOCKER_HOST_IP environment variable to open the connection to MySQL.
Note: if you use bind-address = 0.0.0.0 your MySQL server will listen for connections on all network interfaces. That means your MySQL server could be reached from the Internet ; make sure to set up firewall rules accordingly.
Note 2: if you use bind-address = 172.17.42.1 your MySQL server won't listen for connections made to 127.0.0.1. Processes running on the docker host that would want to connect to MySQL would have to use the 172.17.42.1 IP address.
host mode
To access MySQL running on the docker host from containers in host mode, you can keep bind-address = 127.0.0.1 in your MySQL configuration and connect to 127.0.0.1 from your containers:
[vagrant#docker:~] $ docker run --rm -it --network=host mysql mysql -h 127.0.0.1 -uroot -p
Enter password:
Welcome to the MySQL monitor. Commands end with ; or \g.
Your MySQL connection id is 36
Server version: 5.5.41-0ubuntu0.14.04.1 (Ubuntu)
Copyright (c) 2000, 2014, Oracle and/or its affiliates. All rights reserved.
Oracle is a registered trademark of Oracle Corporation and/or its affiliates. Other names may be trademarks of their respective owners.
Type 'help;' or '\h' for help. Type '\c' to clear the current input statement.
mysql>
note: Do use mysql -h 127.0.0.1 and not mysql -h localhost; otherwise the MySQL client would try to connect using a unix socket.
For all platforms
Docker v 20.10 and above (since December 14th 2020)
Use your internal IP address or connect to the special DNS name host.docker.internal which will resolve to the internal IP address used by the host.
On Linux, using the Docker command, add --add-host=host.docker.internal:host-gateway to your Docker command to enable this feature.
To enable this in Docker Compose on Linux, add the following lines to the container definition:
extra_hosts:
- "host.docker.internal:host-gateway"
For older macOS and Windows versions of Docker
Docker v 18.03 and above (since March 21st 2018)
Use your internal IP address or connect to the special DNS name host.docker.internal which will resolve to the internal IP address used by the host.
Linux support pending https://github.com/docker/for-linux/issues/264
For older macOS versions of Docker
Docker for Mac v 17.12 to v 18.02
Same as above but use docker.for.mac.host.internal instead.
Docker for Mac v 17.06 to v 17.11
Same as above but use docker.for.mac.localhost instead.
Docker for Mac 17.05 and below
To access host machine from the docker container you must attach an IP alias to your network interface. You can bind whichever IP you want, just make sure you're not using it to anything else.
sudo ifconfig lo0 alias 123.123.123.123/24
Then make sure that you server is listening to the IP mentioned above or 0.0.0.0. If it's listening on localhost 127.0.0.1 it will not accept the connection.
Then just point your docker container to this IP and you can access the host machine!
To test you can run something like curl -X GET 123.123.123.123:3000 inside the container.
The alias will reset on every reboot so create a start-up script if necessary.
Solution and more documentation here: https://docs.docker.com/docker-for-mac/networking/#use-cases-and-workarounds
Use
host.docker.internal
instead of
localhost
I doing a hack similar to above posts of get the local IP to map to a alias name (DNS) in the container. The major problem is to get dynamically with a simple script that works both in Linux and OSX the host IP address. I did this script that works in both environments (even in Linux distribution with "$LANG" != "en_*" configured):
ifconfig | grep -E "([0-9]{1,3}\.){3}[0-9]{1,3}" | grep -v 127.0.0.1 | awk '{ print $2 }' | cut -f2 -d: | head -n1
So, using Docker Compose, the full configuration will be:
Startup script (docker-run.sh):
export DOCKERHOST=$(ifconfig | grep -E "([0-9]{1,3}\.){3}[0-9]{1,3}" | grep -v 127.0.0.1 | awk '{ print $2 }' | cut -f2 -d: | head -n1)
docker-compose -f docker-compose.yml up
docker-compose.yml:
myapp:
build: .
ports:
- "80:80"
extra_hosts:
- "dockerhost:$DOCKERHOST"
Then change http://localhost to http://dockerhost in your code.
For a more advance guide of how to customize the DOCKERHOST script, take a look at this post with a explanation of how it works.
Solution for Linux (kernel >=3.6).
Ok, your localhost server has a default docker interface docker0 with IP address 172.17.0.1. Your container started with default network settings --net="bridge".
Enable route_localnet for docker0 interface:
$ sysctl -w net.ipv4.conf.docker0.route_localnet=1
Add these rules to iptables:
$ iptables -t nat -I PREROUTING -i docker0 -d 172.17.0.1 -p tcp --dport 3306 -j DNAT --to 127.0.0.1:3306
$ iptables -t filter -I INPUT -i docker0 -d 127.0.0.1 -p tcp --dport 3306 -j ACCEPT
Create MySQL user with access from '%' that means - from anyone, excluding localhost:
CREATE USER 'user'#'%' IDENTIFIED BY 'password';
Change in your script the mysql-server address to 172.17.0.1.
From the kernel documentation:
route_localnet - BOOLEAN: Do not consider loopback addresses as martian source or destination while routing. This enables the use of 127/8 for local routing purposes (default FALSE).
This worked for me on an NGINX/PHP-FPM stack without touching any code or networking where the app's just expecting to be able to connect to localhost
Mount mysqld.sock from the host to inside the container.
Find the location of the mysql.sock file on the host running mysql:
netstat -ln | awk '/mysql(.*)?\.sock/ { print $9 }'
Mount that file to where it's expected in the docker:
docker run -v /hostpath/to/mysqld.sock:/containerpath/to/mysqld.sock
Possible locations of mysqld.sock:
/tmp/mysqld.sock
/var/run/mysqld/mysqld.sock
/var/lib/mysql/mysql.sock
/Applications/MAMP/tmp/mysql/mysql.sock # if running via MAMP
Until host.docker.internal is working for every platform, you can use my container acting as a NAT gateway without any manual setup:
https://github.com/qoomon/docker-host
Simplest solution for Mac OSX
Just use the IP address of your Mac. On the Mac run this to get the IP address and use it from within the container:
ifconfig | grep 'inet 192'| awk '{ print $2}'
As long as the server running locally on your Mac or in another docker container is listening to 0.0.0.0, the docker container will be able to reach out at that address.
If you just want to access another docker container that is listening on 0.0.0.0 you can use 172.17.0.1
Very simple and quick, check your host IP with ifconfig (linux) or ipconfig (windows) and then create a docker-compose.yml:
version: '3' # specify docker-compose version
services:
nginx:
build: ./ # specify the directory of the Dockerfile
ports:
- "8080:80" # specify port mapping
extra_hosts:
- "dockerhost:<yourIP>"
This way, your container will be able to access your host. When accessing your DB, remember to use the name you specified before, in this case dockerhost and the port of your host in which the DB is running.
Several solutions come to mind:
Move your dependencies into containers first
Make your other services externally accessible and connect to them with that external IP
Run your containers without network isolation
Avoid connecting over the network, use a socket that is mounted as a volume instead
The reason this doesn't work out of the box is that containers run with their own network namespace by default. That means localhost (or 127.0.0.1 pointing to the loopback interface) is unique per container. Connecting to this will connect to the container itself, and not services running outside of docker or inside of a different docker container.
Option 1: If your dependency can be moved into a container, I would do this first. It makes your application stack portable as others try to run your container on their own environment. And you can still publish the port on your host where other services that have not been migrated can still reach it. You can even publish the port to the localhost interface on your docker host to avoid it being externally accessible with a syntax like: -p 127.0.0.1:3306:3306 for the published port.
Option 2: There are a variety of ways to detect the host IP address from inside of the container, but each have a limited number of scenarios where they work (e.g. requiring Docker for Mac). The most portable option is to inject your host IP into the container with something like an environment variable or configuration file, e.g.:
docker run --rm -e "HOST_IP=$(ip route get 1 | sed -n 's/^.*src \([0-9.]*\) .*$/\1/p')" ...
This does require that your service is listening on that external interface, which could be a security concern. For other methods to get the host IP address from inside of the container, see this post.
Slightly less portable is to use host.docker.internal. This works in current versions of Docker for Windows and Docker for Mac. And in 20.10, the capability has been added to Docker for Linux when you pass a special host entry with:
docker run --add-host host.docker.internal:host-gateway ...
The host-gateway is a special value added in Docker 20.10 that automatically expands to a host IP. For more details see this PR.
Option 3: Running without network isolation, i.e. running with --net host, means your application is running on the host network namespace. This is less isolation for the container, and it means you cannot access other containers over a shared docker network with DNS (instead, you need to use published ports to access other containerized applications). But for applications that need to access other services on the host that are only listening on 127.0.0.1 on the host, this can be the easiest option.
Option 4: Various services also allow access over a filesystem based socket. This socket can be mounted into the container as a bind mounted volume, allowing you to access the host service without going over the network. For access to the docker engine, you often see examples of mounting /var/run/docker.sock into the container (giving that container root access to the host). With mysql, you can try something like -v /var/run/mysqld/mysqld.sock:/var/run/mysqld/mysql.sock and then connect to localhost which mysql converts to using the socket.
Solution for Windows 10
Docker Community Edition 17.06.0-ce-win18 2017-06-28 (stable)
You can use DNS name of the host docker.for.win.localhost, to resolve to the internal IP. (Warning some sources mentioned windows but it should be win)
Overview
I needed to do something similar, that is connect from my Docker container to my localhost, which was running the Azure Storage Emulator and CosmosDB Emulator.
The Azure Storage Emulator by default listens on 127.0.0.1, while you can change the IP its bound too, I was looking for a solution that would work with default settings.
This also works for connecting from my Docker container to SQL Server and IIS, both running locally on my host with default port settings.
For windows,
I have changed the database url in spring configuration: spring.datasource.url=jdbc:postgresql://host.docker.internal:5432/apidb
Then build the image and run. It worked for me.
None of the answers worked for me when using Docker Toolbox on Windows 10 Home, but 10.0.2.2 did, since it uses VirtualBox which exposes the host to the VM on this address.
This is not an answer to the actual question. This is how I solved a similar problem. The solution comes totally from: Define Docker Container Networking so Containers can Communicate. Thanks to Nic Raboy
Leaving this here for others who might want to do REST calls between one container and another. Answers the question: what to use in place of localhost in a docker environment?
Get how your network looks like docker network ls
Create a new network docker network create -d my-net
Start the first container docker run -d -p 5000:5000 --network="my-net" --name "first_container" <MyImage1:v0.1>
Check out network settings for first container docker inspect first_container. "Networks": should have 'my-net'
Start the second container docker run -d -p 6000:6000 --network="my-net" --name "second_container" <MyImage2:v0.1>
Check out network settings for second container docker inspect second_container. "Networks": should have 'my-net'
ssh into your second container docker exec -it second_container sh or docker exec -it second_container bash.
Inside of the second container, you can ping the first container by ping first_container. Also, your code calls such as http://localhost:5000 can be replaced by http://first_container:5000
If you're running with --net=host, localhost should work fine. If you're using default networking, use the static IP 172.17.0.1.
See this - https://stackoverflow.com/a/48547074/14120621
For those on Windows, assuming you're using the bridge network driver, you'll want to specifically bind MySQL to the IP address of the hyper-v network interface.
This is done via the configuration file under the normally hidden C:\ProgramData\MySQL folder.
Binding to 0.0.0.0 will not work. The address needed is shown in the docker configuration as well, and in my case was 10.0.75.1.
Edit: I ended up prototyping out the concept on GitHub. Check out: https://github.com/sivabudh/system-in-a-box
First, my answer is geared towards 2 groups of people: those who use a Mac, and those who use Linux.
The host network mode doesn't work on a Mac. You have to use an IP alias, see: https://stackoverflow.com/a/43541681/2713729
What is a host network mode? See: https://docs.docker.com/engine/reference/run/#/network-settings
Secondly, for those of you who are using Linux (my direct experience was with Ubuntu 14.04 LTS and I'm upgrading to 16.04 LTS in production soon), yes, you can make the service running inside a Docker container connect to localhost services running on the Docker host (eg. your laptop).
How?
The key is when you run the Docker container, you have to run it with the host mode. The command looks like this:
docker run --network="host" -id <Docker image ID>
When you do an ifconfig (you will need to apt-get install net-tools your container for ifconfig to be callable) inside your container, you will see that the network interfaces are the same as the one on Docker host (eg. your laptop).
It's important to note that I'm a Mac user, but I run Ubuntu under Parallels, so using a Mac is not a disadvantage. ;-)
And this is how you connect NGINX container to the MySQL running on a localhost.
For Linux, where you cannot change the interface the localhost service binds to
There are two problems we need to solve
Getting the IP of the host
Making our localhost service available to Docker
The first problem can be solved using qoomon's docker-host image, as given by other answers.
You will need to add this container to the same bridge network as your other container so that you can access it. Open a terminal inside your container and ensure that you can ping dockerhost.
bash-5.0# ping dockerhost
PING dockerhost (172.20.0.2): 56 data bytes
64 bytes from 172.20.0.2: seq=0 ttl=64 time=0.523 ms
Now, the harder problem, making the service accessible to docker.
We can use telnet to check if we can access a port on the host (you may need to install this).
The problem is that our container will only be able to access services that bind to all interfaces, such as SSH:
bash-5.0# telnet dockerhost 22
SSH-2.0-OpenSSH_7.6p1 Ubuntu-4ubuntu0.3
But services bound only to localhost will be inaccessible:
bash-5.0# telnet dockerhost 1025
telnet: can't connect to remote host (172.20.0.2): Connection refused
The proper solution here would be to bind the service to dockers bridge network. However, this answer assumes that it is not possible for you to change this. So we will instead use iptables.
First, we need to find the name of the bridge network that docker is using with ifconfig. If you are using an unnamed bridge, this will just be docker0. However, if you are using a named network you will have a bridge starting with br- that docker will be using instead. Mine is br-5cd80298d6f4.
Once we have the name of this bridge, we need to allow routing from this bridge to localhost. This is disabled by default for security reasons:
sysctl -w net.ipv4.conf.<bridge_name>.route_localnet=1
Now to set up our iptables rule. Since our container can only access ports on the docker bridge network, we are going to pretend that our service is actually bound to a port on this network.
To do this, we will forward all requests to <docker_bridge>:port to localhost:port
iptables -t nat -A PREROUTING -p tcp -i <docker_bridge_name> --dport <service_port> -j DNAT --to-destination 127.0.0.1:<service_port>
For example, for my service on port 1025
iptables -t nat -A PREROUTING -p tcp -i br-5cd80298d6f4 --dport 1025 -j DNAT --to-destination 127.0.0.1:1025
You should now be able to access your service from the container:
bash-5.0# telnet dockerhost 1025
220 127.0.0.1 ESMTP Service Ready
First see this answer for the options that you have to fix this problem. But if you use docker-compose you can add network_mode: host to your service and then use 127.0.0.1 to connect to the local host. This is just one of the options described in the answer above. Below you can find how I modified docker-compose.yml from https://github.com/geerlingguy/php-apache-container.git:
---
version: "3"
services:
php-apache:
+ network_mode: host
image: geerlingguy/php-apache:latest
container_name: php-apache
...
+ indicates the line I added.
[Additional info] This has also worked in version 2.2. and "host" or just 'host' are both worked in docker-compose.
---
version: "2.2"
services:
php-apache:
+ network_mode: "host"
or
+ network_mode: host
...
I disagree with the answer from Thomasleveil.
Making mysql bind to 172.17.42.1 will prevent other programs using the database on the host to reach it. This will only work if all your database users are dockerized.
Making mysql bind to 0.0.0.0 will open the db to outside world, which is not only a very bad thing to do, but also contrary to what the original question author wants to do. He explicitly says "The MySql is running on localhost and not exposing a port to the outside world, so its bound on localhost"
To answer the comment from ivant
"Why not bind mysql to docker0 as well?"
This is not possible. The mysql/mariadb documentation explicitly says it is not possible to bind to several interfaces. You can only bind to 0, 1, or all interfaces.
As a conclusion, I have NOT found any way to reach the (localhost only) database on the host from a docker container. That definitely seems like a very very common pattern, but I don't know how to do it.
Try this:
version: '3.5'
services:
yourservice-here:
container_name: container_name
ports:
- "4000:4000"
extra_hosts: # <---- here
- localhost:192.168.1.202
- or-vitualhost.local:192.168.1.202
To get 192.168.1.202, uses ifconfig
This worked for me. Hope this help!
In 7 years the question was asked, it is either docker has changed, or no one tried this way. So I will include my own answer.
I have found all answers use complex methods. Today, I have needed this, and found 2 very simple ways:
use ipconfig or ifconfig on your host and make note of all IP addresses. At least two of them can be used by the container.
I have a fixed local network address on WiFi LAN Adapter: 192.168.1.101. This could be 10.0.1.101. the result will change depending on your router
I use WSL on windows, and it has its own vEthernet address: 172.19.192.1
use host.docker.internal. Most answers have this or another form of it depending on OS. The name suggests it is now globally used by docker.
A third option is to use WAN address of the machine, or in other words IP given by the service provider. However, this may not work if IP is not static, and requires routing and firewall settings.
You need to know the gateway! My solution with local server was to expose it under 0.0.0.0:8000, then run docker with subnet and run container like:
docker network create --subnet=172.35.0.0/16 --gateway 172.35.0.1 SUBNET35
docker run -d -p 4444:4444 --net SUBNET35 <container-you-want-run-place-here>
So, now you can access your loopback through http://172.35.0.1:8000
Connect to the gateway address.
❯ docker network inspect bridge | grep Gateway
"Gateway": "172.17.0.1"
Make sure the process on the host is listening on this interface or on all interfaces and is started after docker. If using systemd, you can add the below to make sure it is started after docker.
[Unit]
After=docker.service
Example
❯ python -m http.server &> /dev/null &
[1] 149976
❯ docker run --rm python python -c "from urllib.request import urlopen;print(b'Directory listing for' in urlopen('http://172.17.0.1:8000').read())"
True
Here is my solution : it works for my case
set local mysql server to public access by comment
#bind-address = 127.0.0.1
in /etc/mysql/mysql.conf.d
restart mysql server
sudo /etc/init.d/mysql restart
run the following command to open user root access any host
mysql -uroot -proot
GRANT ALL PRIVILEGES ON *.* TO 'root'#'%' IDENTIFIED BY 'root' WITH
GRANT OPTION;
FLUSH PRIVILEGES;
create sh script : run_docker.sh
#!bin/bash
HOSTIP=`ip -4 addr show scope global dev eth0 | grep inet | awk '{print \$2}' | cut -d / -f 1`
docker run -it -d --name web-app \
--add-host=local:${HOSTIP} \
-p 8080:8080 \
-e DATABASE_HOST=${HOSTIP} \
-e DATABASE_PORT=3306 \
-e DATABASE_NAME=demo \
-e DATABASE_USER=root \
-e DATABASE_PASSWORD=root \
sopheamak/springboot_docker_mysql
run with docker-composer
version: '2.1'
services:
tomcatwar:
extra_hosts:
- "local:10.1.2.232"
image: sopheamak/springboot_docker_mysql
ports:
- 8080:8080
environment:
- DATABASE_HOST=local
- DATABASE_USER=root
- DATABASE_PASSWORD=root
- DATABASE_NAME=demo
- DATABASE_PORT=3306
You can get the host ip using alpine image
docker run --rm alpine ip route | awk 'NR==1 {print $3}'
This would be more consistent as you're always using alpine to run the command.
Similar to Mariano's answer you can use same command to set an environment variable
DOCKER_HOST=$(docker run --rm alpine ip route | awk 'NR==1 {print $3}') docker-compose up
you can use net alias for your machine
OSX
sudo ifconfig lo0 alias 123.123.123.123/24 up
LINUX
sudo ifconfig lo:0 123.123.123.123 up
then from the container you can see the machine by 123.123.123.123
The CGroups and Namespaces are playing major role in the Container Ecosystem.
Namespace provide a layer of isolation. Each container runs in a separate namespace and its access is limited to that namespace. The Cgroups controls the resource utilization of each container, whereas Namespace controls what a process can see and access the respective resource.
Here is the basic understanding of the solution approach you could follow,
Use Network Namespace
When a container spawns out of image, a network interface is defined and create. This gives the container unique IP address and interface.
$ docker run -it alpine ifconfig
By changing the namespace to host, cotainers networks does not remain isolated to its interface, the process will have access to host machines network interface.
$ docker run -it --net=host alpine ifconfig
If the process listens on ports, they'll be listened on the host interface and mapped to the container.
Use PID Namespace
By changing the Pid namespace allows a container to interact with other process beyond its normal scope.
This container will run in its own namespace.
$ docker run -it alpine ps aux
By changing the namespace to the host, the container can also see all the other processes running on the system.
$ docker run -it --pid=host alpine ps aux
Sharing Namespace
This is a bad practice to do this in production because you are breaking out of the container security model which might open up for vulnerabilities, and easy access to eavesdropper. This is only for debugging tools and understating the loopholes in container security.
The first container is nginx server. This will create a new network and process namespace. This container will bind itself to port 80 of newly created network interface.
$ docker run -d --name http nginx:alpine
Another container can now reuse this namespace,
$ docker run --net=container:http mohan08p/curl curl -s localhost
Also, this container can see the interface with the processes in a shared container.
$ docker run --pid=container:http alpine ps aux
This will allow you give more privileges to containers without changing or restarting the application. In the similar way you can connect to mysql on host, run and debug your application. But, its not recommend to go by this way. Hope it helps.
Until fix is not merged into master branch, to get host IP just run from inside of the container:
ip -4 route list match 0/0 | cut -d' ' -f3
(as suggested by #Mahoney here).
I solved it by creating a user in MySQL for the container's ip:
$ sudo mysql<br>
mysql> create user 'username'#'172.17.0.2' identified by 'password';<br>
Query OK, 0 rows affected (0.00 sec)
mysql> grant all privileges on database_name.* to 'username'#'172.17.0.2' with grant option;<br>
Query OK, 0 rows affected (0.00 sec)
$ sudo vim /etc/mysql/mysql.conf.d/mysqld.cnf
<br>bind-address = 172.17.0.1
$ sudo systemctl restart mysql.service
Then on container: jdbc:mysql://<b>172.17.0.1</b>:3306/database_name

How to run 2 PostgreSQL servers on localhost?

I am trying to run 2 database server on the same machine(localhost). default port is 5432..Is there a way to change it? I create a second cluster and edited the "postgresql.conf" file to change port to 5434 and restart the server but IPV4 and IPV6 are still showing a connection on port 5432. Anyone can help ?
thanks
I found a way to do it:
Create multiple Postgres instances on same machine
pg_ctl -D full/path/to/myCluster -o -pXXXX start
Where -D folder where the cluster is
Where -o is for command line options to pass to postgres
where -pXXXX is the port number you want to connect. You choose any port not taken by another process

How to connect to windows postgres Database from WSL

I'm running Postgres 11 service on my Windows computer.
How can I connect to this database from WSL?
When I try su - postgres:
postgres#LAPTOP-NQ52TKOG:~$ psql
psql: could not connect to server: No such file or directory
Is the server running locally and accepting
connections on Unix domain socket "/var/run/postgresql/.s.PGSQL.5432"
It's trying to connect to a Postgres in WSL. I don't want to run Ubuntu Postgres using:
sudo /etc/init.d/postgresql start
WSL2 assigns IP address to the Windows host dynamically and the IP addresses can change without even rebooting Windows (see Notes below). So to reliably connect we'll need to:
Allow Windows and Postgres to accept connections from the WSL2 IP address range (not allowed by default)
From WSL2, determine the Windows/Postgresql host's IP address (which is dynamic) when connecting via psql. We'll make this convenient via .bashrc and alias.
Unfortunately I couldn't find the exact specification for the WSL2 IP address range. From several tests/reboots it appears that WSL2 is assigning IP addresses primarily in range of 172.*.*.* but I have occasionally been assigned 192.*.*.* so we'll use these when configuring the firewall and Postgres.
Add Windows Firewall Inbound Port Rule for WSL2 IP Addresses:
Open Windows Defender Firewall with Advanced Security
Click New Rule...
Select Port for rule type
Select TCP and for Specific local ports enter 5432
Select Allow the connection. Connecting from WSL2 won't be secure so don't select the secure option
Select at least Public. Can select Domain and Private as well. I could only connect if Public was selected
Name the rule e.g. Postgres - connect from WSL2 and create it
Right click newly created rule and select Properties then click on the Scope tab
Under Remote IP address, select These IP addresses then click Add... and enter range 172.0.0.1 to 172.254.254.254
Repeat step 9 for IP address range 192.0.0.1 to 192.254.254.254
Click Apply then OK
Make sure rule is enabled
Configure Postgres to Accept Connections from WSL2 IP Addresses
Assuming a default install/setup of Postgresql for Windows the following files are located under C:\Program Files\PostgresSQL\$VERSION\data
Verify that postgresql.conf has following set:
listen_addresses = '*'
This should already be set to '*' so nothing do here.
Update pg_hba.conf to allow connections from WSL2 range e.g. for Postgresl 12:
# TYPE DATABASE USER ADDRESS METHOD
# IPv4 local connections:
host all all 127.0.0.1/32 md5
host all all 172.0.0.0/8 md5
host all all 192.0.0.0/8 md5
For Postgresql 13+ you should use scram-sha-256 as the method.
Restart Postgres for changes to take effect. This can be done either from the Windows Services app or from cmd with Administrator privileges e.g. for Postgresql 12:
net stop postgresql-x64-12
net start postgresql-x64-12
WSL Shell Conveniences
In WSL, add following to your ~/.bashrc or similar:
# Add DNS entry for Windows host
if ! $(cat /etc/hosts | grep -q 'winhost'); then
echo 'Adding DNS entry for Windows host in /etc/hosts'
echo '\n# Windows host - added via ~/.bashhrc' | sudo tee -a /etc/hosts
echo -e "$(grep nameserver /etc/resolv.conf | awk '{print $2, " winhost"}')" | sudo tee -a /etc/hosts
fi
Then reload your .bashrc changes: source ~/.bashrc
Usage
psql -h winhost -p 5432 -U postgres
Notes:
The IP address assigned to the Windows host by WSL2 is not the same as the IP address assigned to your physical Windows machine on your network. WSL2 uses vEthernet connections.
You can inspect the vEthernet connections via Control Panel\Network and Internet\Network Connections
Note that when looking at the IPv4 properties that the IP addresses will appear as if they are statically set but they aren't! Try rebooting and inspecting IPv4 properties again
If one day you're unable to connect to Postgres, check that winhost is in the IP address range per firewall rules. Could be WSL has assigned an IP address that we weren't expecting!
In WSL2 you need to use host IP to connect
to get host IP
grep nameserver /etc/resolv.conf | awk '{print $2}'
then you need to allow TCP 5432 inbound Rules in 'Windows Defender Firewall with Advanced Security'
I made my self PS.you still need to allow TCP 5432 in Firewall
put this in ~/.bashrc
cat /etc/hosts | grep 172.; test $? -eq 0 && $1 || echo -e "$(grep nameserver /etc/resolv.conf | awk '{print $2, " host"}')\n$(cat /etc/hosts)" | sudo tee /etc/hosts
its append host IP to /etc/hosts if not exist before(usually happened when restart wsl or computer)
then
psql -h host -p 5432 -U postgres
Specify your host, port, and username explicitly
For example:
psql -h 127.0.0.1 -p 5432 -U postgres
For me what worked was to follow these steps:
Change pg_hba.conf to listen on all interfaces: host all all 0.0.0.0/0 trust
Open firewall for postgresql
Use one of the hostnames in /etc/hosts that pointed to the ip of my host. This hostname for me was: host.docker.internal
This issue can be fixed in two possible ways
Specify the host and user name explicitly
psql -h localhost -U postgres
Or
Navigate to the runpsql.sh file and run the query
/Library/PostgreSQL/14/scripts/runpsql.sh
Now run the psql query by entering password (if needed)

How do I see if memcached is already running on my chosen port?

I am having some problems with memcached and one idea I am having is that perhaps it is already running on the port I am trying to run it on, started by some other user on our network. Is there a way to tell what memcached ports are currently in use?
To see if it is running you could also try telnetting into the port:
telnet localhost 11211
If this works you will see the following (telling you that the given port is open):
Connected to localhost.
Escape character is '^]'.
Now if memcached IS running you can see some basic stats by issuing the given command:
stats
If this fails you will know that memcached is not running.
Try
netstat -ap | grep TheChosenPort#
and see if anything is listening on those TCP or UDP ports.
netstat
In Linux, check via netstat, e.g.
$ sudo netstat -nap | grep memcached
tcp 0 0 127.0.0.1:11211 0.0.0.0:* LISTEN 5067/memcached
ps
Use ps to filter the processes:
$ ps wuax | grep memcache
497 5067 0.0 1.3 384824 53928 ? Ssl Apr11 1:28 memcached -d -p 11211 -u memcached -m 64 -c 1024 -P /var/run/memcached/memcached.pid -l 127.0.0.1
The port can be found next to -p, e.g. -p 11211. If port hasn't been specified, default is 11211.
Bash
You can send stats command to the given port and see if the memcached responds, e.g.
exec 3<>/dev/tcp/localhost/11211; printf "stats\nquit\n" >&3; cat <&3
Telnet
Use telnet to connect to the host and run stats (as above), e.g.
$ telnet localhost 11211
Trying 127.0.0.1...
Connected to localhost.
Escape character is '^]'.
stats
STAT pid 23669
STAT uptime 433859
Then hit Ctrl-] and Ctrl-D to finish.
Use the following command
ps -U user | grep -v grep | grep memcached
You can check memcached status
service memcached status
You will see a line like this at the bottom:
└─1560 /usr/bin/memcached -vv -m 64 -p 11211 -u memcache -l 127.0.0.1 -P /var/run/memcached/memcached.pid
The -p 11211 is what port it's running on.
If you're asking this question, it sounds like you're running a really old version. If you did this on a recent version, you'd see this:
% ./memcached
failed to listen on TCP port 11211: Address already in use