Can anyone please let me know how to upgrade the Datapower firmware version XI52 7.2.0 to 7.7 IDG. When I'm trying to ugrade the firmware I have encountered an error while booting the image as "Product incompatibility:firmware is intended to IDG".
Thanks!
You need to find the correct firmware image and as you write XI52 I assume you have an appliance (hardware) and you can't run IDG firmware in a XI52.
.scrypt3 files are for hardware while .scrypt4 are virtual.
The 7.7 version has been renamed into 2018 so you should grab DataPower-2018.4.1.9-LTS-XI52-2426-7199
Related
We are trying to install a CentOS-based Openfiler distribution on Dell R630 server with PERC H330 mini RAID controller but unfortunately, the installation can't find a hard disk to install the OS.
Any ideas on how to solve that?
The Linux distribution doesn't contain the necessary driver packages. It might be possible to create an an device driver media, like an USB stick, which does contain the RPM installation packages. More information you will find in the Driver Installation section of the handbook.
I have a project built with STEP 7 Basic V13. I try to use it with STEP 7 Basic V13 SP1 upgrade. But after the load with TIA, when I want to do the connection, I get the error "device not reachable". Sometimes, this error becomes "incompatible device". I am not sure what is happening with the configuration.
Please check if the firmware of the selected 1214 CPU matches the one you're using.
Update 1:
Hi friends, could you please recommend me a powered USB hub in Australia(preferred in Melbourne)? I guess my problem is caused by the insufficient power supply.
Hi friends,
I have a FEZ Hydra Basic kit. I got it in 2012 (might be in Sep).
Today I downloaded the latest SDKs, drivers and everything(NETMF and Gadgeteer Package 2014 R1). (.NET Micro Framework 4.3 and the firmware I have on my laptop is 4.2.6.2)
But the firmware on my deivce is 4.1.x.x(I was lucky to saw the device's firmware version just once and I followed the instruction on the software FEZ Config, but failed with errors).
After that, I cannot get the Device's firmware version any more.
I found changing USB ports sometimes help. I have 4 USB ports, some of them can connected to the device, others are not.
So I have no idea to update the firmware in other way.
Could someone please help me to figure out how to find a way to update my firmware?
In the attached image, it shows: the FEZ Config detected the FEZ Hydra and was trying to get the device's firmware version, but it failed to do so and followed by an error message say: Failure - Device is not connected or not responding.
As I mentioned above, I was lucky to see the FEZ Config successfully got the device's version only once.
So my guess is - is it because the output power is not strong enough to support the operation, so I have to use something like a USB hub which has a strong and stable power?(I saw someone mentioned this and cannot find the comments any more).
Bt the way, all USB ports I mentioned above are directly on my laptop which means they get power directly from motherboard, so they should have strong and stable power to support my operations.
I have been stuck at this issue for the whole day, I really hope some friends can help me out.
Thank you very much in advance.
I've had like the same issue. While updating the firmware it threw me that message and I could not reach my Gadgeteer *Fez Hydra at all. I managed to solve it by attaching an external power supply to it. I use the USB Client DP (Dual Power) 1.3. This way you do need the power over USB part and you can safely update the firmware.
USB Client: https://www.ghielectronics.com/catalog/product/280
edit: If that doesn't solve your isse you might want to reset the Loader first. Which is given as a tip on the GHI website before updating the firmware.
I have installed Eucalyptus Cloud in a Box (Bundled with CentOS 6.4 64 bit)on an HP Probook 430 G1 laptop with the following processor specifications
Intel i7 4500u
Before Install I get the message "Unsupported Hardware of combination thereof detected".
Inspite of this I can still install Eucalyptus just fine.
However, after the first reboot and subsequent reboots I see a message
Detected CPU model 6 family 69
UNSUPPORTED HARDWARE device: Intel CPU Model
After this the machine does not go beyond the first loading screen.
1).Is this a problem with the new fourth generation Haswell architecture ?
2).And is there any solution to this apart from using another machine ?
3).What does CPU model 6 family 69 mean ?
4).Is there any way to know which specific hardware is unsupported ?
Below is the link that shows the supported hardware of Red Hat
https://hardware.redhat.com/laptop/Hewlett%20Packard/&quicksearch=
Thank you in advance. Any help will be greatly appreciated
Yes, I believe "Model 6 Family 69" is a 4th generation Haswell i7.
You should be able to add "unsupported_hardware" to your kickstart file, if that's when it's occurring.
I don't know, but here's Intel's information page for what I think is a typical 4th gen processor: http://ark.intel.com/products/76087/Intel-Core-i7-4750HQ-Processor-6M-Cache-up-to-3_20-GHz
You could look at the kernel source for the kernel you're using. Might be in arch/x86/kernel/cpu somewhere.
The "Feature" explained
http://fedoraproject.org/wiki/Anaconda/Features/WarnTaintedHardware
This says it should only affect the installer, so the "subsequent reboots" behavior you describe should not happen unless you're running the installer on every boot.
And a recent feature added to kickstart to allow it to boot unattended:
https://access.redhat.com/site/documentation/en-US/Red_Hat_Enterprise_Linux/6/html-single/6.4_Technical_Notes/
BZ#824963
A kickstart installation on unsupported hardware resulted in a dialog box asking for confirmation before proceeding with the installation process. As a consequence, it was not possible to perform a kickstart installation on unsupported hardware without any user input. To fix this bug, a new unsupported_hardware kickstart command has been added, which skips the interactive dialog warning when installing a system on unsupported hardware without user input.
I can't get to connect my Nexus 7.2 (2nd gen or 2013 or FHD) to Eclispe. I followed all the topics available (even those about Nexus 7.1 first gen.) but the drivers provided by Google or Nexus seem to not work... Impossible to see my new Nexus 7.1 in Eclipse...
I was wondering if I was the only one to experience this problem ? or if someone has found a solution to that problem.
Thanks !
I had this problem but it was solved after I installed the correct drivers through Device Manager (My Nexus 7 showed a warning icon in Device Manager prior). I downloaded the drivers manually.
Also make sure you have the USB Driver here: http://developer.android.com/sdk/win-usb.html
And just in case you weren't aware, you need to have Developer Mode enabled on your Nexus 7.
Well, the answer for me is probably that it doesn't work with Windows 7 Familiale (Home) Premium but it works with Windows 7 Enterprise.