For specific reasons i want to change the Y-axis location from left to right.
so if anyone can help me with the way.
thanks
I search for a long time to set the Y-axis in the right side but OpenModelica does not have that feature.
Related
Is it possible to zoom on individual series in Echarts? By that I mean selecting a series and then applying vertical zoom on that series while the other series remain unchanged.
I have looked at the examples and documentation, but can´t find it.
Yes! It is possible and supported. The way I did it was by setting zoomOnMouseWheel on idividual series through setOption.
Selecting a series by clicking on it seems a little brittle though. The selections don´t always seem to go through. I used the selectchanged event.
As of right now, if I'm floating the chart, the legend will not float with it. I would like to anchor that legend along side(or maybe even inside) the chart. This way when Im draging my chart into positon, I won't have to do the same with the legend. Is there a way to do this? Thanks in advance.
Each object on the dashboard is independent, and only relevant to the top left corner of the dashboard when floating. You can create containers and move the entire container as per this article:
https://help.tableau.com/current/pro/desktop/en-s/dashboards_organize_floatingandtiled.htm
I know anchoring to an object has been an asked for feature in the past going back as far as 2016, that I could find, but I do not know the current in progress status.
I use the Leaflet plug-in "Leaflet.ImageOverlay.Rotated.js" to use its L.imageOverlay.rotated(...) thing in order to overlay certain map pieces in various places on top of the normal map.
It does this by taking an image and having me tell it its top-left, top-right and bottom-left coordinates to figure out how to rotate, tilt and stretch/squeeze it properly.
It took me a very long time to figure these coordinates out by hand. For this reason, I'm looking for some sort of "geopositioning mode", perhaps enabled by this extension, which would simply let me click three times on the map to tell it where these points go. That would be so simple for the developers to do and would help so much. It's such an obvious thing to do that I strongly suspect it's already implemented and ready.
Is there such a "mode"? If not, how am I expected to find the positions without spending so much time and trial-and-error as I did for the first overlay map image?
Added: I should also clarify that the image should be shown in this mode so that you can re-adjust the points and watch in real time as the image bends/warps, to get it just right.
you can develop a modul for this problem.
find minimum 4 point on raster map.
click on tilemap for 4 points
than find different slope and distance same 2 points.
maybe you must rotate and use affine transformation.
How to change the vanishing points (P1,P2,P3) in the perspective in MATLAB 3D figures?
Below there is a scheme of explanation what I mean:
Thanks in advance for your help.
If you want to control the perspective appearance in a plot, you'll want to first change the Projection property of the axes to perspective. Then you can change the various camera properties of the axes to get the view you want. The important ones for adjusting how the perspective looks are the CameraViewAngle and CameraPosition.
I have found that a "realistic" perspective view can be achieved using a CameraViewAngle of about 30 degrees, mimicking the preferred viewing area of the human eye:
The default CameraViewAngle is about 6.6, so setting it to 30 will cause the view to appear zoomed-out. You will then want to change the CameraPosition so that it is closer to the CameraTarget, thus zooming the view back in. You can use a larger CameraViewAngle if you want a more exaggerated perspective (like a fisheye lens).
I'm looking for a way to hide parts of a graph (namely the axes and plot) on a certain side of an axis (enclosed by the red boxes in the image below). I would like the labels to still be visible and the graph to still be scrollable.
I've tried setting visibleRange but it hides the axes for a fixed range, and doesn't quite work when the graph is scrollable.
Thanks in advance for any help.
Set padding on the plot area frame. See the Plot Gallery example app for sample code.
Just i have an idea, but i am not sure whether this will satisfy you or not.
I have used the axisContstrains property for both X and Y axis.
So the plots inside your boxes are not plotted for me. I hope this will help to this questions.