PWM input capture and repeat. STM32F4 - stm32

Question

guys.
I generated PWM signal with timer TIM1.
I want get this PWM from TIM1 with timer TIM2 and repeat it on the some GPIO pin.
I used Standart Peripheral Library.
PWM has generated on pin PA8 with timer TIM1 successfully, but i can't receive this PWM signal from PA0 pin with TIM2.
(PA8 и PA0 i connected with cable.)
Help me, please.
type here
#include "stm32f4xx.h"
#include "stm32f4xx_gpio.h"
#include "stm32f4xx_rcc.h"
#include "stm32f4xx_tim.h"
#include "misc.h"
#include <stdio.h>
GPIO_InitTypeDef GPIO_InitStruct;
TIM_TimeBaseInitTypeDef TIM1_TimeBaseStruct;
TIM_OCInitTypeDef TIM1_OCInitStruct;
TIM_ICInitTypeDef TIM_ICInitStruct;
volatile uint16_t capture1 = 0, capture2 = 0;
volatile uint8_t capture_is_first = 1, capture_is_ready = 0;
const uint32_t myPeriod = 61538 - 1;
const uint32_t myPrescaler = 1 - 1;
const uint32_t myPulse = 5000;
int main(void)
{
RCC_APB2PeriphClockCmd(RCC_APB2Periph_TIM1, ENABLE);
RCC_APB1PeriphClockCmd(RCC_APB1Periph_TIM2, ENABLE);
// Generate PWM on PA8
RCC_AHB1PeriphClockCmd(RCC_AHB1Periph_GPIOA, ENABLE);
GPIO_InitStruct.GPIO_Pin = GPIO_Pin_8;
GPIO_InitStruct.GPIO_Mode = GPIO_Mode_AF;
GPIO_InitStruct.GPIO_OType = GPIO_OType_PP;
GPIO_InitStruct.GPIO_Speed = GPIO_Speed_100MHz;
GPIO_InitStruct.GPIO_PuPd = GPIO_PuPd_UP;
GPIO_Init(GPIOA, &GPIO_InitStruct);
// Input capture PWM on PA0
GPIO_InitStruct.GPIO_Pin = GPIO_Pin_0;
GPIO_InitStruct.GPIO_Mode = GPIO_Mode_IN;
GPIO_InitStruct.GPIO_OType = GPIO_OType_PP;
GPIO_InitStruct.GPIO_Speed = GPIO_Speed_100MHz;
GPIO_InitStruct.GPIO_PuPd = GPIO_PuPd_UP;
GPIO_Init(GPIOA, &GPIO_InitStruct);
GPIO_PinAFConfig(GPIOA, GPIO_PinSource8, GPIO_AF_TIM1);
TIM1_TimeBaseStruct.TIM_Period = myPeriod;
TIM1_TimeBaseStruct.TIM_Prescaler = myPrescaler;
TIM1_TimeBaseStruct.TIM_CounterMode = TIM_CounterMode_Up;
TIM_TimeBaseInit(TIM1, &TIM1_TimeBaseStruct);
TIM1_OCInitStruct.TIM_OCMode = TIM_OCMode_PWM1;
TIM1_OCInitStruct.TIM_OutputState = TIM_OutputState_Enable;
TIM1_OCInitStruct.TIM_Pulse = myPulse;
TIM1_OCInitStruct.TIM_OCPolarity = TIM_OCPolarity_High;
TIM1_OCInitStruct.TIM_OCNPolarity = TIM_OutputState_Disable;
TIM1_OCInitStruct.TIM_OCIdleState = TIM_OCIdleState_Reset;
TIM_OC1Init(TIM1, &TIM1_OCInitStruct);
TIM_OC1PreloadConfig(TIM1, TIM_OCPreload_Enable);
TIM_ARRPreloadConfig(TIM1, ENABLE);
TIM_CtrlPWMOutputs(TIM1, ENABLE);
TIM_Cmd(TIM1, ENABLE);
TIM_TimeBaseInitTypeDef timer_base;
TIM_TimeBaseStructInit(&timer_base);
timer_base.TIM_Prescaler = 24000 - 1;
TIM_ICInitTypeDef timer_ic;
timer_ic.TIM_Channel = TIM_Channel_1;
timer_ic.TIM_ICPolarity = TIM_ICPolarity_Rising;
timer_ic.TIM_ICSelection = TIM_ICSelection_DirectTI;
timer_ic.TIM_ICPrescaler = TIM_ICPSC_DIV1;
timer_ic.TIM_ICFilter = 0;
TIM_ICInit(TIM2, &timer_ic);
TIM_ITConfig(TIM2, TIM_IT_CC1, ENABLE);
NVIC_EnableIRQ(TIM2_IRQn);
/* Включаем таймер */
TIM_Cmd(TIM2, ENABLE);
while (1)
{
}
} // main
void TIM2_IRQHandler(void)
{
int i = 0;
i++;
printf("I'm TIM2 IRQ Handler.");
if (TIM_GetITStatus(TIM2, TIM_IT_CC1) != RESET)
{
TIM_ClearITPendingBit(TIM2, TIM_IT_CC1);
capture1 = capture2;
capture2 = TIM_GetCapture1(TIM2);
if (!capture_is_first)
capture_is_ready = 1;
capture_is_first = 0;
if (TIM_GetFlagStatus(TIM2, TIM_FLAG_CC1OF) != RESET)
{
TIM_ClearFlag(TIM2, TIM_FLAG_CC1OF);
// ...
}
}
}
I wrote the receive (input capture) PWM signal code using examples from the Internet, but i can't debug this. Help please. I'm new to embedded dev.