I'm configuring the RCC to activate clock for peripherals. However, when I use the SFRs to check registers, it doesn't match what I programmed.
RCC->AHBENR = (uint32_t) 0x000C0004;
When I check the AHBENR,the value is
0x14
I previously had only 0x00000014, so I am not sure if I'm compiling a previous build or why is half of my code being ignored?
In pseudo code, here is what the RCC does. It runs only once:
//Initialises HSE, CSS, HSI
//wait until HSE is ready
//Configure PLL to choose SYSCLK, fix the multiplicator at chosen value
//Fix PREDIV
//Activate PLL
**//Configure clock for peripherals. <- problem here.**
Related
This seems to be a problem that is somewhat common, but I have been unsuccessful with any of the solutions I have found online. Specifically I am trying to transmit a 1024 byte buffer (full 128x64 px image) to a SSD1306 display via I2C/DMA and the HAL generated in cubeIDE. I am using a STML432 nucleo board. I have no problem transmitting the buffer without DMA using HAL_I2C_Mem_Write
Based on other questions I have seen, the problem lies in the fact that the DMA finishes while the I2C bus is still working on the transmit. I just don't know how to remedy this and the examples given usually don't use the HAL (unfortunately, despite my efforts I am not quite competent to correctly apply them to the HAL myself I guess). I have tried using the interrupts for I2c and DMA with no luck, only about the first 254 bytes get transferred (just shy of two rows showing on the screen).
Here is my code for sending the buffer:
static void ssd1306_WriteMData_DMA(const uint8_t *data, uint16_t size)
{
while(HAL_I2C_GetState(&hi2c1) != HAL_I2C_STATE_READY);
HAL_I2C_Mem_Write_DMA(&hi2c1, I2C_ADDR, SSD1306_REG_MDAT, 1, (uint8_t*)data, size);
}
and the code for each interrupt handler:
void I2C1_EV_IRQHandler(void)
{
/* USER CODE BEGIN I2C1_EV_IRQn 0 */
if(I2C1->ISR & I2C_ISR_TCR){
I2C1->CR2 |= (I2C_CR2_STOP);// stop i2c
I2C1->ICR |= (I2C_ICR_STOPCF);// Reset the ICR flag.
// stop DMA
DMA1->IFCR |= DMA_IFCR_CTCIF6;
// clear flag
DMA1_Channel6->CCR &= ~DMA_CCR_EN;
}
/* USER CODE END I2C1_EV_IRQn 0 */
//HAL_I2C_EV_IRQHandler(&hi2c1);
/* USER CODE BEGIN I2C1_EV_IRQn 1 */
/* USER CODE END I2C1_EV_IRQn 1 */
}
void DMA1_Channel6_IRQHandler(void)
{
/* USER CODE BEGIN DMA1_Channel6_IRQn 0 */
// stop DMA
DMA1->IFCR |= DMA_IFCR_CTCIF6;
// clear flag
DMA1_Channel6->CCR &= ~DMA_CCR_EN;
/* USER CODE END DMA1_Channel6_IRQn 0 */
HAL_DMA_IRQHandler(&hdma_i2c1_tx);
/* USER CODE BEGIN DMA1_Channel6_IRQn 1 */
/* USER CODE END DMA1_Channel6_IRQn 1 */
}
I think that is all the pertinent code, let me know if there is something else I am missing. All of the initialization code for the peripherals was done through cubeMX, but I can post that if need be, or the settings. I feel like it is something really simple that I'm missing, but this is a bit over my head to be honest so I don't quite grasp exactly what's going on...
Thanks for any help!
Problem is in your custom DMA1_Channel6_IRQHandler and I2C1_EV_IRQHandler. Those functions will be called right after I2C transfers 255 bytes, which is MAX_NBYTE_SIZE for NBYTES. HAL already have all required interrupt routines inside stm32l4xx_hal_i2c.c:
Sets I2C transfer IRQ handler to I2C_Master_ISR_DMA;
Checks if data size is larger than 255 bytes and uses reload mode.
Sets I2C DMA complete callback to I2C_DMAMasterTransmitCplt;
Starts DMA using HAL_DMA_Start_IT()
Configures I2C registers using I2C_TransferConfig()
HAL driver will handle all I2C+DMA interrupts using I2C_Master_ISR_DMA and I2C_DMAMasterTransmitCplt:
I2C_DMAMasterTransmitCplt will restart DMA for each chunk of 255 (MAX_NBYTE_SIZE) or less bytes.
I2C_Master_ISR_DMA will reset RELOAD/NBYTES registers using I2C_TransferConfig.
For last block of data I2C_AUTOEND_MODE is used.
So all you need is
remove "user code" from DMA1_Channel6_IRQHandler and I2C1_EV_IRQHandler functions
enable I2C1 event interrupt in STM32 Device Configuration Tool
configure DMA with data width byte/byte
perform a single call of HAL_I2C_Mem_Write_DMA(...) to start transfer
check HAL_I2C_STATE_READY before next transfer
See HAL_I2C_Mem_Write_DMA, I2C_Master_ISR_DMA and I2C_DMAMasterTransmitCplt source code in stm32l4xx_hal_i2c.c to understand how it works.
About why DMA finishes while I2C is still working: HAL driver sends I2C data over DMA using 255 byte chunks, stops DMA, starts DMA, clears I2C_CR2 NBYTES/RELOAD, enables DMA. DMA may be run continuously using DMA_CIRCULAR mode, but currently it is not implemented in HAL I2C drivers. Here is example of using I2C with DMA_CIRCULAR mode:
// DMA enabled single time
hi2c1.hdmatx->XferCpltCallback = MY_I2C_DMAMasterTransmitCplt;
HAL_DMA_Start_IT(hi2c1.hdmatx, (uint32_t)&i2cBuffer, (uint32_t)&hi2c1.Instance->TXDR, I2C_BUFFER_SIZE);
MY_I2C_TransferConfig(&hi2c1, (uint16_t)DAC_ADDR, 254, I2C_RELOAD_MODE, I2C_GENERATE_START_WRITE); // in first call using I2C_GENERATE_START_WRITE
uint32_t tmpisr = I2C_IT_TCI;
__HAL_I2C_ENABLE_IT(&hi2c1, tmpisr);
hi2c1.Instance->CR1 |= I2C_CR1_TXDMAEN;
Still need to clear I2C_CR2 NBYTES/RELOAD using MY_I2C_TransferConfig each 254 bytes (I do not use 255 to align interrupt firing to even index in array):
static HAL_StatusTypeDef MY_I2C_Master_ISR_DMA(struct __I2C_HandleTypeDef *hi2c, uint32_t ITFlags, uint32_t ITSources)
{
if (__HAL_I2C_GET_FLAG(&hi2c1, I2C_FLAG_TCR) == SET)
{
MY_I2C_TransferConfig(&hi2c1, (uint16_t)DAC_ADDR, 254, I2C_RELOAD_MODE, I2C_NO_STARTSTOP); // in repeated calls using I2C_NO_STARTSTOP
}
return HAL_OK;
}
With this approach DMA circular buffer size is not limited to 255 bytes:
#define I2C_BUFFER_SIZE 1024
uint8_t i2cBuffer[I2C_BUFFER_SIZE];
Main.c should have MY_I2C_TransferConfig() function, which is copy pasted version of private function HAL_I2C_TransferConfig() from stm32l4xx_hal_i2c.c. On earlier STM32 microcontrollers there is no NBYTES/RELOAD fields and I2C_CR2 does not need to be updated this way.
Using DMA in circular mode allows to achieve highest frame rate, you just need to fill DMA buffers in time using XferHalfCpltCallback and XferCpltCallback callbacks. Frames may be copied from larger buffer by using memcpy() or DMA MEMTOMEM transfer.
You haven't said which STM32 you are using. They have different bit definitions (because the I2C peripherals in the earlier released parts were rubbish) but it looks like you are using one of the later ones.
Basically you can find what you need in the bit definitions for the I2C registers in the reference manual. If you are setting stop before it has finished you need to look for a BUSY bit that gets cleared or BTF (byte transfer finished) bit that gets set when it is time for you to send stop.
I'm trying to toggle an LED at PC13 by toggling PC14, the problem is that the interrupt handler is kept being called without toggling PC14 and the the pending interrupt is not cleared using EXTI->PR register, nor cleared manually using the debugger. I tried also clearing it in NVIC->ICPR, I'm not sure why there are two registers for clearing the same interrupt.
here is my code
and you can find the header in
https://github.com/AymenSekhri/tinyHAL-STM32f103/tree/master/STM32F103-HAL/tinyHAL
/*
* Description:
* Toggle LED at C13 whenever C14 goes from HIGH to LOW.
*
*/
#include "tinyHAL/stm32f103_hal.h"
int main(){
//Enable AFIO clock from RCC
enablePeripheralClock(Peripheral_AFIO);
//Enable and configure C13 & C14
enablePeripheralClock(Peripheral_GPIOC);
configureGPIO(Peripheral_GPIOC, 13, GPIO_MODE_OUT_50MHZ, GPIO_CONF_OUT_PUSHPULL);
configureGPIO(Peripheral_GPIOC, 14, GPIO_MODE_IN, GPIO_CONF_IN_PUSHUP_PULLDOWN);
//Link EXTI14 to C14
AFIO->EXTICR[3] = (AFIO->EXTICR[3] & ~(0xF<<8)) | 2;
//Configure inturrput at EXTI14 falling edge
EXTI->FTSR |= 1<<14;
//Unmask interrupt 40 (EXTI10-15)
EXTI->IMR |= 1<<14;
//Set Priority to interrupt 40 (EXTI10-15)
NVIC->IP[40] |= 0x10;
//Enable interrupt 40 (EXTI10-15)
NVIC->ISER[40>>5] |= (1 << (40&0x1F));
while(1);
}
void EXTI15_10_IRQHandler(void){
toggleGPIOBit(Peripheral_GPIOC, 13);
if (EXTI->PR & (1 << 14)){
EXTI->PR |= (1 << 14);
}
//NVIC->ICPR[40>>5] |= (1 << (40&0x1F));
__COMPILER_BARRIER();
}
The best solution to get rid of the electronic noise at the pin that (over-)triggers your EXTI is to improve the hardware - but this is the software board, not the electronic one.
If you had a TIM channel connected to that pin, I would recommend to use it to filter the signal coming in. But I think that PC14 doesn't have a timer.
The second-best solution (and this is where workarounds have already started!) is to use a timer (the TIM, not its channel), either to establish a periodic time base to sample the pin (by DMA or by an ISR, and feed samples into a software-based filtering...) - or to deactivate the EXTI interrupt in the EXTI ISR, start the timer and re-activate the EXTI interrupt when the timer expired.
Both of these µC-based approaches are clumsy and clearly inferior to developing a good hardware. This doesn't say that with a "good" hardware you shouldn't add some debouncing or noise protection inside your software!
As #P__J__ suggest add some denouncing logic. There are two methods for de-bouncing like suing RC filter and using software de-bouncing logic.
Due to noise on the pins ISR is getting executed continously.
You can check one more thing.
Try pulling UP/Down the pin and observe the behaviour. ISR should not get executed if logic level doesn't change on Pin.
Maybe It's because of TAMPER/RTC second output redirected to PC13. I also faced the same problem before when using PC13 as EXTI. Set BKP_RTCCR->ASOE to 1 to force it as alarm output that will never triggered because i dont't set any rtc alarm.
I am trying to implement the following scenario on STM32F103C8 Microcontroller.
On PB11 and PB10 I've LED and Button connected respectively. LED is blinking continuously 500ms, but when button is pressed it blinks with 100ms delay 20 times.
I have also connected UART (PA3-PA2) and Potentiometer on ADC (PA0). My task is to transfer ADC reading to UART in DMA mode.
LED and Button interrupt worked well, but as soon as i have added the code for ADC and USART handling it stopped working.
Could you please advice, where is my mistake in ADC-DMA-UART processing and how can i fix it?
Snippets from Main.c
//Buffer for ADC.
uint16_t buffer[5];
huart2.Instance->CR3 |= USART_CR3_DMAT;
//Transfer ADC reading to Buffer in DMA.
HAL_ADC_Start_DMA(&hadc1, (uint32_t*)buffer, 5);
while (1)
{
//LED blinking
HAL_GPIO_TogglePin(GPIOB, LED_Pin);
HAL_Delay(500);
}
//ADC callback function - When buffer is full transfer to UART.
void HAL_ADC_ConvCpltCallback(ADC_HandleTypeDef* hadc) {
HAL_DMA_Start_IT(&hdma_usart2_tx, (uint32_t)buffer, (uint32_t)&huart2.Instance->DR, sizeof(buffer));
}
//Interrupt handler for Button.
void EXTI15_10_IRQHandler(void) {
HAL_GPIO_EXTI_IRQHandler(BT_Pin);
}
//Callback function for Button.
void HAL_GPIO_EXTI_Callback(uint16_t GPIO_Pin){
if(GPIO_Pin == BT_Pin){
for(volatile int i=20; i>0; i--){
HAL_GPIO_TogglePin(GPIOB, LED_Pin);
HAL_Delay(100);
}
}
The most likely reason to me is that the ADC interrupt handler (including ST library functions and the callback you presented) is triggered too frequently, so that the ISR of the EXTI triggered by the push button is suppressed (permanently or nearly permanently).
This can happen even more easily if you selected a minimal sample time and continuous conversion mode (because sampling and conversion then happen as often as it goes, and the IRQ that triggers your conversion-complete callback (HAL_ADC_ConvCmpltCallback()) might run all the time.
In order to verify/falsify my assumption, please inspect
your interrupt priorities for ADC and EXTI (and others you may have on the system)
what happens if you select a longer ADC sampling period, or if you slow down the clock source of the ADC (without slowing down the CPU clock, of course).
If this didn't fix your problem, you may be able post another, refined question.
I'm using a STM32L432 device with FreeRTOS and STM32CubeMX.
I try to implement a M2M-Communication via USART based on an ASCII protocol. The protocol sequences can differ in length but have a maximum length and a defined end character ('\r' / 0x0D).
So I thought about collecting all RX-USART data with DMA (like a FIFO) and using the address match isr based on the USART_ICR_CMCF flag to determine an end character.
Initialize USART1 and enable address match isr
void HAL_UART_MspInit(UART_HandleTypeDef* uartHandle) {
GPIO_InitTypeDef GPIO_InitStruct = {0};
if(uartHandle->Instance==USART1) {
/* USART1 clock enable */
__HAL_RCC_USART1_CLK_ENABLE();
__HAL_RCC_GPIOA_CLK_ENABLE();
GPIO_InitStruct.Pin = GPIO_PIN_9|GPIO_PIN_10;
GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
GPIO_InitStruct.Pull = GPIO_NOPULL;
GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_VERY_HIGH;
GPIO_InitStruct.Alternate = GPIO_AF7_USART1;
HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
/* USART1 interrupt Init */
HAL_NVIC_SetPriority(USART1_IRQn, 5, 0);
HAL_NVIC_EnableIRQ(USART1_IRQn);
/* USER CODE BEGIN USART1_MspInit 1 */
USART1->CR2 |= 0x0D000000; // \r 0x0D
__HAL_UART_ENABLE_IT(&huart1,UART_IT_CM);
}
}
USART1 isr handler
void USART1_IRQHandler(void) {
if (USART1->ISR & USART_ISR_CMF) {
data = USART1->RDR;
SET_BIT(USART1->ICR,USART_ICR_CMCF);
}
HAL_UART_IRQHandler(&huart1);
}
Right now, the address match isr works fine, but I don't have a idea how to implement the DMA / FIFO support.
BTW:
I was very surprised, that the device doesn't support a USART HW FIFO. Is my idea to use DMA to reproduce the FIFO commonly used?
The point of DMA is to not involve the CPU in every byte being transferred. If your ISR is being called for every byte then CPU gets involved so simultaneously enabling DMA, if at all that is possible, won't yield any performance benefits. Get rid of any one of the two - per byte interrupts or the DMA. If you most definitely want to check for a particular character as it arrives then DMA would not help.
Another popular approach to detect end of input when using arbitrary length input along with DMA is to use the USART idle interrupt. This interrupt is triggered when one byte time (time required to transfer one byte at current baud rate) elapses without any transfer. In this interrupt you can transfer the DMA buffer contents to another memory location then reinitialize DMA for future input and leave. Or you can process the input then and there. You can do whatever you want in the Idle ISR as long as the ISR completes execution quickly.
If your input has large continuous runs of data then the idle interrupt would trigger after a long time and you might have overwritten your buffer by then. You can use other DMA interrupts like Half Complete and Full Complete to handle this. So that can be taken care of too. I personally found this method to be buggy during stress testing. But there is no reason for it to be so, I didn't get enough time to debug it when I tried to use it but you will find articles online about this technique.
I'm using STM32L152RB board and I'm trying to configure system clock to use PLL clock but the RCC_FLAG_PLLRDY flag is getting set so the program is stuck in while loop. please let what I'm doing wrong
EnableHSI();
RCC_PLLConfig(RCC_PLLSource_HSI,RCC_PLLMul_3,RCC_PLLDiv_2);
RCC_PLLCmd(ENABLE);
while(RCC_GetFlagStatus(RCC_FLAG_PLLRDY) == RESET);
RCC_SYSCLKConfig( RCC_SYSCLKSource_PLLCLK);
t=GetSystemClockSource();
Take a look in the reference manual for "Relation between CPU clock frequency and Flash memory read time". It says what for the CPU speed higher than 16MHz you should set flash latency for 1WS (wait state).
Something like this before setting PLL as clock source:
FLASH->ACR = FLASH_ACR_ACC64; // 64-bit access
FLASH->ACR |= FLASH_ACR_LATENCY; // one wait state
FLASH->ACR |= FLASH_ACR_PRFTEN; // prefetch enable