I have a problem with getting GSM connection to work.
Currently used:
Advantech UNO-2272G device
Ubuntu 18.04
NetworkManager/nmcli package
The card works when put in a mobile phone.
*Note: following screenshots are made over SSH and remotely, as the device is currently plugged in ethernet until this issue is resolved.
This is current state of "nmcli" command:
nmcli print
The system connection for GSM is called "radi". My guess is that somehow the interface of that connection is trying to work with the other interface (underlined in red), which in turn is trying to get its DNS conf from router (to which it currently is connected with ethernet, but nothing changes if device is plugged out from router and NetworkManager and network is restarted, it still tries to get to router for its DNS).
This is current state of "ip addr" command:
ip addr
This is current state of /etc/network/interfaces file:
interfaces
This is current state of /etc/NetworkManager/system-connections/radi file:
systemconnection
So, the question is, what am I missing here? Is it the interface issue as written above, or something else entirely?
Disclaimer: I am not that proficient in the stuff presented here, most if not all of it was configured following guidelines on the internet.
Hey I'm not expert in this but I do have a different cellular modem connected to a linux system (RPI) and working with NetworkManager (and ModemManager). My modem was connected by a serial UART port (ttyACM0) so that seems similar to what you have done.
When I configured my cellular connection profile in NM I had to setup the ppp section of the connection profile on top of the gsm part. I also went into my ppp options (on the host) and configured those to match a chat script that came from my modem manufacturer. WHen NetworkManager runs a ppp interface it expects the ppp options for the pppd (daemon) to be configured properly.
Here is the ppp section of my NetworkManager cellular connection settings file. Most are defaults and in my case I only added the baud rate for my modem (since it was connected to a UART).
ppp.noauth: yes
ppp.refuse-eap: no
ppp.refuse-pap: no
ppp.refuse-chap: no
ppp.refuse-mschap: no
ppp.refuse-mschapv2: no
ppp.nobsdcomp: no
ppp.nodeflate: no
ppp.no-vj-comp: no
ppp.require-mppe: no
ppp.require-mppe-128: no
ppp.mppe-stateful: no
ppp.crtscts: no
ppp.baud: 115200
ppp.mru: 0
ppp.mtu: auto
ppp.lcp-echo-failure: 0
ppp.lcp-echo-interval: 0
If this is not helpful then have a look at this thread on NM and routing. In their case eth0 was a local network interface and eth1 was their cellular interface
Now to save you 10 hours of troubleshooting - note that the route
metric is independent of the DNS priority! So if you still have
connectivity issues, make sure it's not a DNS resolution issue (eg.
your DHCP server is providing a dummy resolution service). If it is,
then increase the ipv4.dns-priority of your eth0 connection to make it
lower priority, and/or make sure the ipv4.dns-search of your eth1 is
set to "~" to make it the go-to option.
The installation is in a holidays house (so no permanent internet access)
I have a 4g-Routerm (ROUTER-1 = huawei B525-b23) that enable the internet access. I switch it on one day a week.
I have another router (ROUTER-2 = GL-MT300N-V2).
ROUTER-2 is always plugged on electricity.
On ROUTER-2 is connected through ethernet port a Raspberry-Pi3 (with Home Assistant on it).
On ROUTER-2 is connected through WIFI a Camera IP
ROUTER-1 and ROUTER-2 are connected together through ethernet.
When ROUTER-1 is not plug to electricity, none have acces to internet, but it's not an issue.
The camera save picture on the Rapbery Pi3, the Home Assistat is recording some sensor data.
When I switch on the electricity on the ROUTER-1, everyone have access to internet.
What I want is to have remote Access to my router-2 and my Rasberry and my Camera when ROUTER-1 is online
How should I do ?
Hi I can think of two solutions for this setup but both involve buying a second hand cheap router.
I think the use of a single router would make this setup a lot easier. Any router would work that supports:a USB 4g Modem to be attached to it, and has support for setting up a openvpn server and you need to be OK with leaving the Internet on all the time just make sure you dont have any services running that use up bandwidth and you should be ok. You can can connect both raspberry pi and IP camera to that router. Setup Openvpn server open the UDP port required and download the certificates, You should be able to vpn into your network and manage it through SSH or something remotely.
The second option is tailored to you but still requires swapping the 4G Modem with another one that supports these things: Wake on LAN, openvpn server, supports ssh into it over LAN and either has 4G support through a sim card slot or a usb port with modem support.
You can then have it setup so this new Router-1 is switched off with wake on lan configured on it and the raspberry pi to send the magic packet. You can use something like this to get an idea of how WoL https://www.lifewire.com/wake-on-lan-4149800. You can use cron on your raspberry pi to send WoL signal to Router 1 once a week which would eventually give you internet access once the router is up. You have to setup a vpn server on it and forward the required port and download the certificates. When your scheduled WoL cron runs make sure you are able to connect through vpn then access network resources you wish, at the end when you are done you can ssh into the router-1 and turn it off.
I hope this helps. I had a look at the router models you are using and it doesnt leave you with many options. You can get cheap second hand routers online that support everything that is required.
I have a raspberry pi 3 connected to my PC (Windows 7) via ethernet using DHCP server and VNC viewer and it works perfectly.
The pc is connected to a WIFI.
I want to access to internet from my raspberry pi, I tried the ICS sharing but it didn't work:
I shared the wifi connection:here
changed the ip address: here
after sharing the wifi connection, I am unable to access internet from both the pc and rasp even though they are in the same ip address.
On PC,On the Rasp
Can you please help me to find a solution?
Thank you.
You have to create a network bridge.
Select the two networks, right click and select bridge connections.
I'd use static IP address on your PI and your PC's ethernet
I configured hostapd to make an Access Point Wi-Fi network on my raspberry pi... everything works fine. It acts like a router.
Can i bind client devices via WPS? For example phones, ESP8266 that support WPS connections?
I implemented a web service for an Android application. The web service is running on my local host (192.168.1.2). Using the Android emulator I succeeded to connect to web service. The I tried to connect my Android device using debugging mode to web service but it didn't work. So my question is if it is possible to connect an Android device to this web service that is running on my local host (192.168.1.2) without using a real IP ?
It's much simpler way supported by google!
Connect your phone via usb to computer and enable usb debugging
On your computer open Chrome browser and type exactly this address: chrome://inspect/#devices
Now you can link your computer port to your device port by port forwarding button. On my computer I have service on address localhost:61437 and I just linked it to device's 8081 port. Remeber to check 'Enable port forwarding' checkbox
screen from service on my computer ( localhost:61437 )
screen from my mobile browser with the same service ( localhost:8081). And that's it. Also you use this service address in your application
Did you already solve your problem? I also got a problem like you. These are the steps that I already done:
unplug lan cable or turn off any other internet connection from your pc.
connect your android mobile to your pc using usb.
turn on usb tethering
back to your pc. check your ip. mine is 192.168.42.37
check your webservice app in your pc. let's say http://192.168.42.37/webserviceapp
back to your android mobile. try this url http://192.168.42.37/webserviceapp
Now you can access your webservice app in your pc from your mobile phone.
Well your localhost is 127.0.0.1 (or ::1) and your LAN IP is 192.168.1.2. Each pc/device that are connected under your LAN could reach your webservice on IP 192.168.1.2
Your Android device must be so connected under the same LAN maybe through Wifi connection so it will be able to talk with 192.168.1.2.
If you can't connect your Android device under the same LAN eg you have just a 3g connection you need to play with your router/firewall to redirect all incoming traffic (maybe just the http traffic) from your public ip to you private ip (192.168.1.2)
Hope this help
I'll throw in my process, since nothing on SO worked for me. Here are the steps I took to connect my physical android device to the web service running on my laptop (connected to the phone) on localhost:
Enable USB debugging on your Android device
Run your web service on your machine. My web service runs on localhost, port 3000 in development: http://localhost:3000/api/...
Run ifconfig (Unix), or ipconfig (Windows)
Find your machine's inet address on your LAN interface. Mine is 10.0.0.121 for interface wlan0. Externally, it is 68.43.XX.XXX, which is not the address that you want to use.
Use the LAN IP since you are connecting to your service on LAN, otherwise you might get an econnrefused (connection refused) error due to firewall rules
Build your http URL with that IP address, and the port that your web service is running on. For me, it's http://10.0.0.121:3000/api/...
When you launch your app, you should connections to your local web service in logs, Wireshark, etc, and you should see the desired activity/data in your Android application.
I had the same issues, researched a lot then found out that you have to explicitly make changes in your firewall settings. Your firewall is blocking your code to be accessed from external source. So, all you need to do is, go to firewall settings, add port 80 (in my case since, I am using Apache http Server) for inbound and outbound. Now, you can test it on your phone's browser http://192.16..**:80/
I've done that on a Mac using GasMask and Charles Proxy Server. Your phone and your computer have to be on the same network.
say the webservice url you want to access is at http://api.xyz.com, you first use GasMask to point that url to your localhost, then use Charles to set up a proxy server. Then you go to the settings on your phone, go into Wi-Fi, long-press the network you are connected to, choose Modify Network, and enter the proxy settings Charles gave you.
In my case, nothing of these solutions works because Windows firewall blocks it, but putting a rule on the firewall hasn't effect.
The problem in my case is that my laptop is connected with Wifi and Windows had the Wifi connection like a Public network. I must to change the network connection to Private network. http://www.comofuncionatodo.net/tecnologia/informatica/como-cambiar-de-red-publica-a-red-privada-en-windows-10/
I agree with the other answers as good approaches if you don't want to expose your DEV webservice on the internet. However, it's much easier if you do just expose the webservice. There's a number of free DNS services, but I've found no-ip to be the easiest to set up. I use it for exactly the purpose that you asked about; so I can test with my DEV webservice on a real device.
If you choose to go with no-ip (I have no affiliation with that company, it's just the one I've used and am familiar with), you can get a free publicly accessible URL like http://MyExampleWebServer.no-ip-org, and no-ip has a utility you can install so even if you're behind a dynamic IP, it will always keep the correct external IP associated with that URL. If you're working from your house, then you'd just need to make sure you port forward traffic from port 80 to your internal 192.x.x.x IP address (or whatever port you use; maybe 443 for ssl).
It's as easy as that, and now you can hit that webservice from any device that can access the internet.
I haven't worked with it, but I believe dyndns also offers a similar service.
This solution is for GAE development server in Eclipse
Step 1: Get the LAN IP
Goto your Windows Command Console (Press Win+R, then type "cmd"). In the console, enter "ipconfig". You will see a list of display. Under Wireless LAN adapter Wi-Fi, get the IPv4 Address. It will be something 192.168.x.x
LAN IP : 192.168.x.x
Step 2:
Go to Eclipse, Open the Configured server
Under Properties of GAE Development Server -> Local Interface address to bind to, enter the LAN IP address, and save.
Step 3:
Now you can access the GAE server by
http://192.168.x.x:8888/
8888 - Refers to the Port Number, as mentioned in the GAE development server
In order to access local web services using their own server hosts rather than IP addresses with ports, do these following steps:
Make sure your Android device and your local machine are on the same network.
Install SquidMan on your Mac, Linux, or any other Proxy Server.
Configure the proxy server's HTTPPort (ex. 5555) and clients (ex. 192.168.0.0/24) to your own network mask, and run the proxy server.
You are either using the web services in:
a. A web browser: Configure the proxy settings of your Android device from Modify WiFi networks.
b. Android application:
Set up the Proxy for your HTTP client. If you are using Volley, check this out: Volley Behind a Proxy server.
You can now connect to it by using whatever URL you are using on your host to connect to the web service (ex. http://my-local-machine.com)
Hint: If you got 4xx response codes, make sure your web service allows connections from other non-local-hosts.
If you are referring your localhost on your system from the Android emulator then you have to use
http://10.0.2.2:8080/
Because Android emulator runs inside a Virtual Machine(QEMU) therefore here 127.0.0.1 or localhost will be emulator's own loopback address.